Bitumen Penetration Grade 80/100 is a standard penetration grade Bitumen usually used as a Paving Grade Bitumen suitable for road construction and for the production of asphalt pavements with superior properties. This grade of Bitumen is mainly used in the manufacture of hot mix asphalt for bases and wearing courses. Penetration Grade Bitumen supplied by ASI GLOBAL TRADE is petroleum grade bitumen, manufactured from fractional / vacuum distillation of crude oil. The Bitumen supplied by ASI GLOBAL TRADE is produced from vacuum residue (short residue) feedstock. Penetration Grade bitumens are specified by the penetration and softening point test. Designation is by penetration range only. The penetration grade bitumens have a thermoplastic property which causes the material to soften at high temperatures and to harden at lower temperatures. This unique temperature/ viscosity relationship is important when determining the performance parameters such as the adhesion, rheology, durability and application temperatures of bitumen. SPECIFICATIONS : CHARACTERISTIC TEST METHOD UNIT MIN. MAX. Specific gravity at 25°C ASTM D70 °C 1.01 1.05 Penetration at 25°C ASTM D5 mm 80 100 Softening Point ASTM D36 °C 42 52 Ductility at 25°C ASTM D113 Cm 100 - Loss on heating ASTM D6 % 0,5 Flash Point ASTM D92 °C 225 Solubility in Trychloroethyelene ASTM D2042 % 99 Performance after RTFOT Method Test to ASTN D1754: - Change in mass (m/m) ASTM2872 % - 0.5 - Retained Penetration 25°C, 100g, 5s (% of original) ASTM D5 % 50 - - Increase in softening point ASTM D36 °C - â?¤8 - Softening point after hardening ASTM D36 °C 45 - LEGAL NOTES The information, and, in particular, the recommendations relating to the application and end-use of ASI GLOBAL TRADE products, are given in good faith based on ASI GLOBAL TRADE current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with ASI GLOBL TRADE recommendations. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchant-ability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written recommendations, or from any other advice offered. The user of the product must test the products suitability for the intended application and purpose. ASI GLOBAL TRADE reserves the right to change the properties of its products. The proprietary rights of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. Users must always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.
Bitumen 60/70 Test method Unit Specification Specific gravity @ 25°C ASTM D70 Kg/cm3 1.01/1.06 Penetration @ 25°C ASTM D5 mm/10 60/70 Softening point °C ASTM D36 °C 49/56 Ductility @25 °C ASTM D113 cm 100 min Loss on heating(wt) % ASTM D6 wt % 0.2 max Drop in penetration after heating % ASTM D5-D6 % 20 max Flashpoint °C ASTM D92 °C 232 min Solubility in Trichloroethylene ASTM D2042 wt % 99 min Spot test A.A.S.H.O.T102 Negative
ASI GLOBAL TRADE guarantees that the Bitumen Grades supplies under its offers is produced in compliance to and is in conformity to Standard AASTHO M20-70 and ASTM D946/D946M and meets the following specification requirements.
Bonny Terminal Light Crude Oil is a high-quality oil with low sulfur and high API gravity. It is produced in Nigeria and exported to refineries around the world. We offer the secured payment terms, with no prepayment required. You can contract directly with the refinery, without any intermediaries. If you are looking for a reliable and cost-effective source of crude oil,
High-quality Russian Base Oil, SN 150 (LVI) SN 150 (blend, VI 95+) SN 350 SN 400 SN 500 BS (23-26cst) BS 150 (28-34cst) VHVI-4 Tatneft (VI 120+, typically around 130-133) VHVI-6, VHVI-8 with VI 114-120
Specifications Test Method Min. Max. Kinematic Viscosity at 100°C ASTM D-445 9.5 11.2 Viscosity Index ASTM D-2270 87 95 Flash Point °C ASTM D-92 208 240 Pour Point °C ASTM D-97 -16 0 Total Acid number mg KOH/g ASTM D-664 - 0.05 Color ASTM D-1500 1.5 2 Auto-ignition temperature ASTM D2155 402 °C PHYSICAL PROPERTIES: APPEARANCE: liquid Bulk density: 7.4 lbs/gal [ASTM D1250] Color: dark Solubility: Insoluble in water Specific gravity: 0.89 at 16ï?°C [ASTM D1298] Molecular weight: 690
Commodity : Bitumen 50- 70 Type : Eastern European Penetration : at 25°C (50-70) Softening Point : at 0°C (46-54) Resistance to Hardening : at 1630c Change of Mass % : Max -0.5 Retained Penetration : Min -50 Softening Point After Hardening : Minimum Deg. C-48 Flash Point Minimum : Deg. C230 Solubility Minimum : %99 Kinematic Viscosity : at 135 Deg. C, Minimum mm2/s 295 Delivery : CIF Paranagua Port Quantity : 200 Metric Ton (MT) Spot for Test Extension 2000 MT Contract for 12 mos.
Bitumen 80/100 Test method Unit Specification Specific gravity @ 25 ASTM D70 Kg/cm3 1.01/1.06 Penetration @ 25 ASTM D5 mm/10 80/100 Softening point ASTM D36 42/50 Ductility @25 ASTM D113 cm 100 min Loss on heating(wt) % ASTM D6 wt % 0.2 max Drop in penetration after heating % ASTM D5-D6 % 20 max Flash point ASTM D92 250 min Solubility is CS2(wt) % ASTM D4 wt % 99.5 min Spot test A.A.S.H.O.T102 Negative
Bitumen 40/50 Test method Unit Specification Specific gravity @ 25°c ASTM D70 Kg/cm3 1.01/1.06 Penetration @ 25°c ASTM D5 mm/10 40/50 Softening point °c ASTM D36 °C 52/60 Ductility @25 °c ASTM D113 cm 100 min Loss on heating(wt) % ASTM D6 wt % 0.2 max Drop in penetration after heating % ASTM D5-D6 % 20 max Flash point °c ASTM D92 °C 250 min Solubility is CS2(wt) % ASTM D4 wt % 99.5 min Spot test A.A.S.H.O.T102 Negative
Bitumen 60/70 Test method Unit Specification Specific gravity @ 25°C ASTM D70 Kg/cm3 1.01/1.06 Penetration @ 25°C ASTM D5 mm/10 60/70 Softening point °C ASTM D36 °C 49/56 Ductility @25 °C ASTM D113 cm 100 min Loss on heating(wt) % ASTM D6 wt % 0.2 max Drop in penetration after heating % ASTM D5-D6 % 20 max Flashpoint °C ASTM D92 °C 232 min Solubility in Trichloroethylene ASTM D2042 wt % 99 min Spot test A.A.S.H.O.T102 Negative
Bitumen 10/20 Test method Unit Specification Specific gravity @ 25°c ASTM D70 Kg/cm3 1.01/1.06 Penetration @ 25°c ASTM D5 Mm/10 10/20 Softening point °c ASTM D36 °C 58/66 Ductility @25 °c ASTM D113 Cm 100 min Loss on heating(wt) % ASTM D6 wt % 0.2 max Drop in penetration after heating % ASTM D5-D6 % 20 max Flashpoint c ASTM D92 °C 250 min Solubility is CS2(wt) % ASTM D4 wt % 99.5 max Spot test A.a.s.h.o.t102 Negative
Bitumen 30/40 Test method Unit Specification Specific gravity @ 25°c ASTM D70 Kg/cm3 1.01/1.06 Penetration @ 25°c ASTM D5 mm/10 30/40 Softening point °c ASTM D36 °C 55/63 Ductility @25 °c ASTM D113 cm 100 min Loss on heating(wt) % ASTM D6 wt % 0.2 max Drop in penetration after heating % ASTM D5-D6 % 20 max Flash point °c ASTM D92 °C 250 min Solubility is CS2(wt) % ASTM D4 wt % 99.5 min Spot test A.A.S.H.O.T102 Negative
Bitumen 120/150 Test method Unit Specification Specific gravity @ 25°C ASTM D70 Kg/m3 1000-1050 Penetration @ 25°C ASTM D5 mm/10 120/150 Softening point °C ASTM D36 °C 38 min Ductility @25 °C ASTM D113 Cm 100 min Loss on heating(wt) % ASTM D6 wt % 0.5 max Drop in penetration after heating % ASTM D5-D6 % 20 max Flashpoint °C ASTM D92 °C 218 min Solubility in Trichloroethylene ASTM D2042 wt % 99 min Spot test â?? Negative
Bitumen 80/100 Test method Unit Specification Specific gravity @ 25°c ASTM D70 Kg/cm3 1.01/1.06 Penetration @ 25°c ASTM D5 mm/10 80/100 Softening point °c ASTM D36 °C 42/50 Ductility @25 °c ASTM D113 cm 100 min Loss on heating(wt) % ASTM D6 wt % 0.2 max Drop in penetration after heating % ASTM D5-D6 % 20 max Flash point °c ASTM D92 °C 250 min Solubility is CS2(wt) % ASTM D4 wt % 99.5 min Spot test A.A.S.H.O.T102 Negative
Dear Sir/Mdm, We would like to offer our BI Product from Tank Cleaning - Sludge Oil. Monthly Supply: 2 Million Liter. If you interest, You can email me Regards Danny
we are the prime intermediary for Eastern SiberiaPacific Ocean oil pipeline , confirm delivery to 100000 mtons to major port. All inquiries welcome.
We supplies different types of paraffin waxes that can be used in Personal Care, Adhesives, Candles, Inks and Coatings, Textiles and Polishes, Wax Compounding and other specialty applications. They function as lubricants, base materials, viscosity modifiers, etc, ensuring excellent performance at a competitive price. We offers a range of fully refined paraffin covering a wide range of melting points from 52°C to 68°C. Our general purpose paraffin waxes cover EPIWAX, Sasolwax, Renox and Woodshield brands. Specialty Blends: We has a comprehensive range of pharmaceutical grade waxes, specially formulated for use in personal care products like lipsticks, creams, lotions, depilatory products and color cosmetics, etc. Our Sasolwax grades display excellent performance, and exhibits consistently high quality products. In terms of standards, Sasolwax products are GMP, ISO and HACCP certified., for your peace of mind. We offer a comprehensive range of pharmaceutical grade paraffin waxes ranging from soft (Sasolwax 4608) to hard paraffin waxes (Sasolwax 5105, Sasolwax 5803 and Sasolwax 6203). Candle: We also supply specially formulated waxes for various targeted applications like wick coating waxes (Sasolwax 8204, Sasolwax 6301, etc) and candle extrusion (Sasolwax 0716, etc). In addition, we provide a unique range of specially formulated waxes, EPIWAX A10, A11 and A12, for use in crystal-effect candles. Additives: We also has a range of specialty wax additive, EPIWAX EM11 and EM12, for the manufacture of mottle-effect candles. For use in gel candles, we recommend Kraton G1650 for a transparent effect.
We supply a wide range of technical, cosmetic and pharmaceutical grade liquid paraffins, for use in the area of personal care, adhesives and polymer modification. N-Paraffin Our EPISOL range of n-paraffins, are fully synthetic, and are produced by a unique technology involving the direct synthesis of CO and H2. Being synthetic, it is ultra-pure, water-white and characterized by the absence of nitrogen compounds, sulphur, aromatics and other impurities. Applications for this product range from the area of metal working to part of hot melt pressure sensitive adhesives (HMPSA) formulation. Overall, our EPISOL range of n-paraffins cover a range of viscosities, are of low toxicity and are readily biodegradable, specially suited for the environmentally conscious producer. White Oils: Sasol Wax’s Merkur and our in house EPOIL brands of pharmaceutical, cosmetic and technical grade white oils are available in various viscosities. These Merkur and EPOIL grades are suitable for use in personal care products, pharmaceutical balms and ointments, etc. Polymerisation Solvents: Our EPOIL range of hydrocarbon oils are highly pure, and can be used as diluents for catalysts in various industrial applications. They are inert and free of catalyst poisons like sulphur compounds, carbonyls, oxygenates, cyclic compounds, etc. Solvent-Solvent Extraction: Our range of EPOIL and EPISOL liquid paraffins are suitable for use as metal extraction diluents, especially in the area of solvent-solvent extraction. Chlorinated Paraffin: EPChem provides chlorinated paraffin products by NCP Chlorchem, which is a South African-based manufacturer. The products have chlorine content ranging from 45-55% under the brand of PLASTICLOR e.g. CP52. It is commonly used in PVC compounding to produce flexible PVC as well as in paints. They act as an effective plasticizer and flame retardant additive in paints.
Crude palm kernel oil.
Mazut M100 Russian origin Mazut M100 miniumum 30 000 mts
