Although technologies over electrical vehicle has been developed for years, we still dont have a perfect thermal management solution over electrical vehicle battery pack. Besides the reasons of battery pack structure, I think thermal interface materials has a great impact on thermal management. The market of thermal gap filler(thermally conductive adhesive) looks very chaotic, many thermal gap filler was called thermal adhesive for structure bond, actually, they are still thermal silicone encapsulant in essence. Moreover, some engineers dont know thermal materials very well and state requirements unclear, resulting a unsatified trial and failed impression on domestic brand. Many manufacturers only concerned to thermal conductivity and laid less attention on other parameters, such as curing time, curing status, bond strength, maintaince. GLPOLY thermal gap filler (thermally conductive adhesive) XK-D25H is epoxy based, high performance and good electrical insulation thermal adhesive which had been improved from traditional epoxy adhesive. Mix ratio is 1:1 by volume, just a few of manufacturers can accomplish it, for example, 3M thermally conductive epoxy adhesive mix ratio is 2:1. It is truth that data can be checked out from website. GLPOLY thermally conductive adhesive (thermal gap filler) XK-D25H features 1) short curing time, draft in 5 minutes and become steady in 12 hours, 2) semi rigid after curing, protect battery modules by dampening vibration, 3) Improved bond strength greater than 3.7Mpa, 4) mix ratio 1:1 by volume, fit for dispensing equipment. One of battery customers tested and compared materials among five suppliers, they checked thermal conductivity, electrical insulation, curing time and bond strength and so on. Two of suppliers were eliminated because of longer curing time that it is unfavourable for process. In the high temperature aging test, GLPOLY thermally conductive adhesive (thermal gap filler) XK-D25H performed normally, the variety of parameters are less than 10%. The competing one failed because of week bond strength, and moreover, its mix ratio is 2:1 which is unfavourable for customers robot system. Besides stable thermal performance, GLPOLY thermally conductive adhesive provides reliable physical ptoperties. 1)filling gaps under low pressure, 2) low stress, 3) strong structure bond. GLPOLY thermal materials has been applied in military equipment because of high performance and reliable properties. Thermal gap filler is on trial in battery pack in four major enterprises. GLPOLY thermal materials help you keep you devices cool and well performed.
Strong products: CaF2/BaF2/MgF2/LiF/Si crystal blanks/rods and their windows/lenses/wafer.
1. Raw materials: ferrosilicon scrap, ferrosilicon powder and binder 2, the production process Sampling and testing raw material ferrosilicon scrap, ferrosilicon powder, in line with the production indicators, the ferrosilicon powder and binder into the mixer and stir evenly, through the conveyor belt into the ball press into a 10-50mm sphere, Output through the conveyor. Sampling and testing the finished silicon iron ball, sent to the second-three test room for testing, the test results meet the customer's requirements and then bagged and ready for shipment. 3. Product index Si: >65%; C: 2.0%; P: 0.05%; S: 0.03%; Al: 3.0%; Fe: 15-20% Size: 10-50mm 90%min, Package : 1 Mt Big Bag 4. Characteristics: The same effect of ferrosilicon and ferrosilicon is the indispensable deoxidizer and alloying agent in the steelmaking process. It can improve the furnace temperature, increase the fluidity of molten iron, effectively discharge slag, and improve pig iron and castings. Toughness and cutting ability. First, the uniform granularity reduces the loss, labor, electricity and transportation of the natural block of ferrosilicon used in steelmaking. Second, the product has uniform particle size, accurate feeding, good deoxidation effect, shortening deoxidation time, saving energy, improving steelmaking efficiency, improving quality, low raw and auxiliary materials consumption, high recovery rate and reducing labor intensity. Third, the melting speed is fast, the division is even, and the power consumption is reduced. 5. Usage: The method of use is exactly the same as that of ferrosilicon.
Si-C alloy is a new alloy of alloys for converters. It can replace ferrosilicon, silicon carbide and carbon reductant, reduce the amount of deoxidizer, and be used in converter smelting deoxidation alloying process. The effect is stable, chemical composition and mechanical properties of steel. The internal control quality is superior to the traditional process. Its characteristics: improve the quality of molten steel, improve product quality, improve product new energy, reduce the amount of alloy added, reduce steelmaking costs, and increase economic efficiency.
liquid methyl silicone resins for coatings This product has excellent heat resistance, electrical insulation, and moisture resistance. It is suitable for H - grade motor, transformer coil, transistor sealing, H - grade glass wire dipping and high-temperature resistant coating, etc. Item Index Appearance Light yellow or red-brown liquid, opalescence is permitted, no mechanical impurity Solid content((150,2h,%) 50±1 Viscosity (4# cup,25, S) no less than 15 Drying Time(200, Copper Sheet, h) No more than2 Mass Loss(400,3h,%) No more than 5
Silicone free thermal pad, silicone free, non-silicone, thermal gap pad Silicone free thermal inter materials are getting more and more attention recently. GLPOLY is at cutting edge of non silicone thermal interface materials development. Thermal solution design shows the tendency of diversification, for example, more amd more engineers tend to design non silicone thermal pad for electric vehicle, because they are only use thermal silicone pad before. One of our customers designed thermal solution with bergquist Gap pad 2200SF, after he inquiried the supplier, he wanted to use silicone free thermal pad from a local supplier because of the long lead time, unfavorable price. Vehicle Control Unit controls the electric engine, gear box and power battery for improving economy, dynamic performance, security and environmental concert. Thus it can be seen, VCU is such a critical element, thermal managent on VCU can not be underestimated. GLPOLY has designed silicone free thermal pad XK-PN30 for thermal management system of electric vehicle which could be perfect alternative to bergquist Gap Pad 2200SF. More and more customers inquiry GLPOLY silicone free thermal pad XK-PN30. GLPOLY can provides a perfect alternative to Gap Pad 2200SF. We offered samples free of charge for testing performance. Thermal conductivity of XK-PN30 is 3.0W/mK, thermal impedance is 0.2in2/W, thermal performance is higher than that of thermal gap pad 2200SF. We are a local manufacturer, we promised a lead time of 15-business days, and 30% off on the gap pad 2200SFs price. Also we can die-cut parts according to customers requirements. With better performance, favorable price as well as shorter lead time, GLPOLY XK-PN30 has gained increasing recognition from EV manufacturers and thermal management engineers. GLPOLY XK-PN30 is a perfect alternative to Bergquist Gap Pad 2200SF.
Oxygen Content:
Lengthï¼?50~250mm Side Length: 156±0.5mm Oxygen Content::
6N Polycrystalline Silicon
Parallel to the surface distance: 125 ± 0.5mm/125 ± 0.5mm/156 ± 0.5mm Other parameters: parameters with solar grade silicon rod Technical approach: solar grade silicon rod by the square root of machine rounded machined products.
Granule 1-4mm 99.99%
FESI ALLOYS SI:65% 68% 70% 72% 75% Ca: 1-1.5% Al: 2%max LUMPS,GRANULARS OR FINE SIZE.
addition cure rtv2 liquid silicone for making mold 1. Description YJS-620 is a two-component 1:1 Mix addition (platinum)cured RTV silicone rubber which cures at room temperature. Because of its considerable fluidity, it is recommended for the duplication of models with many undercuts. This stuff is really thin and easy to pour. 2. Features *high chemical resistance to the aggressive components of some types of resin *High resistance to laceration (this characteristic guarantees high resistance to wear and tear) *High level of accuracy in reproducing very small particulars *High dimensional stability over time and non-deformability *Considerable resistance to high temperatures and to ageing *Excellent non-stick effect *Soft, stretchy, high tear resistance, *Will not shrink in service 3. Technical datasheet Typical general characteristics Inspection Method Value Product data (Catalyzed A+B) YJS-620 Hardness Shore A 20±2 Mix Ratio A:B 1:1/10:1 Color / translucent Pot life 25 °C (77F) 30-40mins Curing time 25 °C (77F) 3-4 hours Mixed viscosity mPa.s 5000±1000 Tear-strength kg/cm 20±2 Tensile-strength M.pa 4.0±1.0 Elongation % 500±50 Shrinkage % â?¤0.1% 3. Common uses *Wax *Urethane (polyurethane) *Plaster Hydrocal, Hydrostone *Polyester casting resin *Low melt metals (mold life can be short) *Cement, Concrete *Epoxy *Soap *Chocolate 4.SHELF LIFE: When stored at or below 32°C (89.6°F) in the original unopened containers, G-8 series Silicone have a usable life of 12 months. 5.Package 1kg/drum; 20kg/drum;25kg/drum;200kg/drum.
1.Product Description YJS-720 two components platinum cured silicone with 1:1 mixing ratio by weight. It is soft food grade silicone, with 20 Shore A hardness, which is suitable used for moulding chocolate & icing sugar, candy, cakes, fondant. 2.Features: A. Amazing fluidity and easy to operate A. Platinum-based, food-grade silicone (environmental friendly, odorless and non-toxic) B. Delicate design available C. Mixing ration: 1:1, easy to mix D. Easy de-molding E. Excellent tension and tear strength F. High performance in duplication G. Shrinkage is almost zero (below 0.1) H. Excellent resistance to weather, temperature, aging, acid and aging-proofing. I. High resistance to high temperature and aging(resist -60 to 250) J. Food safe 3.Technical Data Typical general characteristics Inspection Method Value Product data (Catalyzed A+B) YJS-720 Hardness Shore A 20±2 Mix Ratio A:B 1:1/10:1 Color / translucent Pot life 25 °C (77F) 30-40mins Curing time 25 °C (77F) 3-4 hours Mixed viscosity mPa.s 5000±1000 Tear-strength kg/cm 20±2 Tensile-strength M.pa 4.0±1.0 Elongation % 500±50 Shrinkage % â?¤0.1% 4.Appearance: Part A: a non-toxic and odorless liquid with translucent color and platinum inside Part B: a non-toxic and odorless liquid with translucent color. ATT: We can do any curing time as your requirements. Notice: What is the hardness should I choose Normally 5~55 Shore A will be the best, but it also should according to your size and pattern design. 5.SHELF LIFE: When stored at or below 32°C (89.6°F) in the original unopened containers, G-8 series Silicone have a usable life of 12 months. 6.Package 1kg/drum; 20kg/drum;25kg/drum;200kg/drum.
1. Description YJS-620 is a two-component 1:1 Mix addition (platinum)cured RTV silicone rubber which cures at room temperature. Because of its considerable fluidity, it is recommended for the duplication of models with many undercuts. This stuff is really thin and easy to pour. 2. Features *high chemical resistance to the aggressive components of some types of resin *High resistance to laceration (this characteristic guarantees high resistance to wear and tear) *High level of accuracy in reproducing very small particulars *High dimensional stability over time and non-deformability *Considerable resistance to high temperatures and to ageing *Excellent non-stick effect *Soft, stretchy, high tear resistance, *Will not shrink in service
RTV 2 Liquid Silicone Rubber is a type of Room Temperature Vulcanization Silicone rubber, contains two parts, Part A is silicone rubber, and Part B is cure agent / catalyst, when the part A and part B mix evenly at the ratio of 100:2, the silicone rubber will be cured. RTV 2 Liquid Silicone Rubber can be used for all types of products molds making, such as : Gypsum / plaster. Cement, Artificail Stone, GRC, GFRC, GRC,Tires ,PU ,Resin ,Soap ,Candle etc, for all size from small to few meters .
RTV 2 ( Tin Cured ) Silicone Rubber RTV 2 Liquid Silicone Rubber is a type of Room Temperature Vulcanization Silicone rubber, contains two parts, Part A is silicone rubber, and Part B is cure agent / catalyst, when the part A and part B mix evenly at the ratio of 100:2, the silicone rubber will be cured. RTV 2 Liquid Silicone Rubber can be used for all types of products molds making, such as : Gypsum / plaster. Cement, Artificail Stone, GRC, GFRC, GRC,Tires ,PU ,Resin ,Soap ,Candle etc, for all size from small to few meters .
The conductive elastomer have good conductive, and the products are mainly used in army electronic equipments like spaceflight, aviation, ect. We can produce this products according the drawing supplied by our customers. The materials: silicon with silver/aluminium, silicon with silver/copper, silicon with silver/glass, silicon with nickel/carbon. Durometer:65�5shorea. Volume resistivity:
PRODUCT NAME: Agricultural Silicone Trisiloxano adjuvant TEST ITEM SPECIFICATIONS INSPECTION RESULTS Appearance light amber liquid light amber liquid Viscosity, 25°C,mm2/s 20-61 30 Surface Tension, 25°C,mN/m 20.0-23.0 21.3 Specific Gravity, 25°C, g/cm3 1.001-1.050 1.015 RRESULTS: Up to the standard whatsapp/tel/ 8614707090699 QS-308 spray adjuvant is a super-spreading surfactant based on a trisiloxane ethoxylate. QS-308 spray adjuvant lowers the surface tension of spray solutions, beyond that which is achievable with conventional adjuvants. Typically, QS-308 spray adjuvant (@ 0.1 wt %) gives an aqueous surface tension of
Electronic potting compound silicone Technical guidelines of electronic potting silicon rubber 1, please put part a and part b in separate container and stir evenly before mixing the two part together. 2, weight ratio: part a: part b = 1:1 3, deaeration the mixture under 0.08 m pa for 3 minutes. 4, the temperature influences the curing time of 9355 electronic potting silicon rubber. When in too low temperature, we suggest customers appropriately heat the mixture to accelerate vulcanization. Warm tips of electronic potting silicon rubber: 1.The following material may hinder the curing of the product.So please apply after summary experiment. When necessary, please clean the application areas. Condensation silicone which not completely cured or organic tin compounds Sulfur, sulfide and sulfur rubber materials. Amine compounds as well as contains the amine materials. Pewters solder flux. 2. Should be sealed storage.The mixture should be used up at once, avoid causing waste. 3. Electronic potting silicon rubber belongs to non-dangerous goods, but keep away from mouth and eyes. 4. When electronic potting silicon rubber gets stratified after a period of storage, please mix 9301 evenly before using, it does not affect the performance. 20kgs/drum, 25kgs/drum, 200kgs/drum
