ARG 100 is a hydrolytically stable Silicone polyether surfactant, which can be used in wide range of applications in Paints, Agriculture, PU Foams, Textile, Petroleum Refineries, Detergents, Automotive and Household cleaning products, due to its excellent surface property (surface tension below 22 dynes/cm). SS ARG 166 is used as emulsifier in Textiles and other applications. SS ARG 110 is a Super Wetting and Spreading Agent, which have a low molecular weight nonionic silicone surfactant, developed to improve the wetting, spreading and penetration of agricultural chemicals. It may be used as a formulation ingredient in pesticide products, or as a tank-mix adjuvant for foliar applied chemicals SS ARG 210 All purpose cost effective Spray Adjuvant , which on mixing with insecticides, fungicides, herbicides and other agriculture chemicals increases their penetration, spread and efficiency.
Potassium methyl siliconate (Aquarest WR 100) is an aqueous solution of Potassium methyl Siliconate, Water dilutable. It provides water repellent properties by reaction with atmospheric carbon dioxide. Silane Siloxane Base coat (Aquarest WR 1000) It is suitable for coating painted surfaces too, as this does not impart any color change to the substrate. Forms an excellent weather coat for all types of cement and stone surfaces. Reactive Silicone based (Aquarest 1200) is a solvent soluble fast curing reactive silicone, used for imparting a colorless water repellent surface finish for variety of industries. Reactive Silicone emulsion (Aquarest 1300) is reactive Fluid emulsion water soluble especially designed for treating substrates to impart and improve water repellent properties. Silane based water soluble (Aquarest WR 1100) is a solvent less, water- soluble, Silane Siloxane Emulsion. Dilute solutions of SS WR 1100 serve as general-purpose water repellents for impregnating and priming mineral surfaces. Rust remover and Protective lubricant (SS WRC) is a speciality silicone lubricant for rust loosener and remover, water repellent for metal and also used for protection from corrosion.
SS AF is General purpose Antifoam – Defoamer Emulsion to provide effective antifoaming and defoaming solutions in aqueous systems for variety of industrial applications. SS AF 5730 & 5520 is an excellent Antifoam Emulsion specially designed to control form in high temperature (over boil) and broad pH range ( 4-10) in aqueous systems. SS AF 700 Powdered Antifoam been developed to control the foam generated during process or using Powder Insecticides, Pesticides, Detergents and Fertilizers.
A long chain silicone gum with controlled vinyl level is combined with fumed, precipitated silica as reinforcing filler along with various other materials and additives to create special properties. Once you cure the compounds at high temperature (100~200 ºC) after mixing with catalysts it becomes HTV silicone rubber. The molding process can be compression, extrusion, etc. Main applications: Baby products: Baby nipple, baby bib, etc. Medical products: catheter and negative pressure drainage ball. Kitchen products: bake ware, silicone scoop, etc. Industry product:: Key button, sealing rings and small parts. Electric product: cable accessories, insulator, etc. Sports product: swim cap, goggle, etc.
SS ARG 110 is use as an Adjuvant refers to the use of this product as an additive to a pesticide for the purpose of enhancing the pesticide’s effectiveness for wetting more of the leaf surface (delivering the pesticide to a greater surface area for increased leaf penetration) and thereby providing rain fastness. i.e., herbicides are not washed off by rainfall because they have penetrated into the plant surface. Enhances the performance of agricultural chemicals, especially water-soluble broadleaf herbicides, insecticides, fungicides and plant growth regulators
1. 1:1 addition type, good adhesive strength and self-healing 2. High elongation, excellent flexibility for mechanical stress relieving 3. Low oil penetration after cured, good anti-poisoning property 4. Good dielectric in high temperature for high voltage protection 5. Excellent aging resistance and weatherability 6. Excellent waterproof, corrosion prevention, moisture proof and chemical media resistance Used for encapsulation of various modules, semi-conductor, IGBT, automotive ECU module, IC chip, weighing sensor, waterproof connector. PROPERTY STANDARD/UNITS VALUE of SI2709 ---- ---- PART A PART B Material ---- Polysiloxane Hydrogen polysiloxane Color Visual inspection Colorless Liquid Colorless Liquid Viscosity 7;C, cps 800~1000 800~1000 Density 7;C, g/cm3 0.99 0.99 Mixture/mass ratio ---- A:B=100:100 Viscosity of mixture 7;C, cps 800~1000 Operation time 7;C, min 60 Cure condition RTV or HEAT 7;C /6 hour;67;C /30min Cured appearance ---- Colorless transparent gel Needle penetration 1/mm 75 Dielectric strength KV/mm 25 Volume resistance DC500V, ohm-cm 1.0¨¢1015 Loss factor 1 MHz88;0.001 Dielectric constant 1 MHz 2.8 Application temperature7;C -60~260 Part Aa10 KG/Bucket, Part Ba10 KG/ Bucket.
1.Solvent free two component material 2.Transparent both before and after cured 3.Platinum catalyzed curing system 4.No by-products after curing 5.Low viscosity before cured, easy to application 6.Excellent flexibility, free from stress 7.Extremely low oil exudation, good anti-poisoning 8.By adjusting the mix rate of part A and part B, can adjust the gel adhesion 9.It can stick repeatable 10.It can use with polyethylene release liner 11.Pass test of physiological compatibility, poison cell, skin stimulus etc. PROPERTY STANDARD/UNITS VALUE of SI2721 ---- ---- PART A PART B Material ---- Polysiloxane Hydrogen polysiloxane Color Visual inspection Transparent Liquid Transparent Liquid Viscosity 7;C, cps 61;¨¤150161;¨¤150 Density 7;C, g/cm3 0.99 0.99 Mixture/mass ratio ---- A:B=100: (80~120) Viscosity of mixture 7;C, cps 800¨¤150 Operation time 7;C, min ¡ê¾60 Cure condition RTV or HEAT 7;C /6 hour; 67;C /5min Cured appearance ---- Transparent gel Application temperature §C -60~200 Part Aa20 KG/Bucket, Part Ba20 KG/ Bucket; Part Aa200 KG/Drum, Part Ba20 KG/ Drum. Part A is also available in 200 kg metal drums accompanied by the corresponding 200 kg of Part B.
Chemical name : Polydimethylsiloxane CAS No. : 63148-62-9 EINECE : 618-493-1 Apperance : colorless and transparent Physical and chemical features : a.Smoothness & softness & hydrophobicity & good chemical stability & insulation property b.High and low temperature resistance & high flash point. c.Low freezing point (it can be chronically used in the temperature from -50? to +200 ?). d.Small viscosity-temperature coefficicent & big compression ratio & low surface tension. -
5N-6N
Size:28x24.5x4cm Weight:315g Color:pantone code 28x24.5x4
Fesi75-aSi 74.0~80.0Mn 0.4Ca 0.3Cr 0.1P 0.035S 0.02 Package: 1mt jumbo bag Dimensions: 0-10mm, 10-100mm
Si purity: 99.7% min, 99.9%min or 99.99%min Packing: 25kgs/bag Size:pls contact us for more details. 25kgs/woven bag.
Ferro silic: 72%min / 75%min Al: 2%max C: 0.2%max S: 0.02%max P: 0.04%max Size: 10-60mm 90%min Packing in 1 mt bag and then put in containers
1. Used in aluminum: an additive to aluminum alloys, silicon is used to increase the fluidity and tenacity of Aluminum and its alloys, which enjoy good castability and weldability accordingly. 2. Used in organic chemicals: silicon metal is used in manufacturing a number of sorts of silicones, resins, and lubricants. 3. Used in electronic parts: silicon metal is used in producing monocrystalline and polycrystalline silicon of high purity for electronic parts, such as semi conductors, etc. In plastic woven bags of about 10KG,250 KG and 1MT net each.
Applications of RTV-2 manual molding silicone rubber It is mainly applied in manual mold design, PVC plastic mould, cement product mould, low melting-point alloy mould, alloy toy craft, plastic toy, craftwork, gift and stationery, big statue, cultural relic duplication and reproductions; pad printing orientation, electronic appliances vibration resistance, etc. Features of RTV-2 manual molding silicone rubber Low shrinkage,no deformation of the mould, good elasticity, the more moulds duplicated the better, etc.
Si 75%min, al 2.0%max, c 0.2%max, s 0.03%max, p 0.04%max Size: 10-50mm, Packing: in 1 mt big bag
ferro silicon Ferrosilicon Lumps Si:75%/72%min Al:2.0%max C:0.2%max S:0.02%max P:0.04%max. Ferrosilicon Fines Si:75%/72% Al:2.0%max C:0.2%max S:0.02%max P:0.04%max Size:90%min or at buyer's option In 1mt PP woven bag . In 1mt pp woven bag Size:1-3mm,3-10mm,10-50mm,50-100mm 90%min or at buyer's option In 1mt PP woven bag .
Type conductivity - P, N.
Silicon metal 441 Si:99.0%min. Fe:0.4%max. Al:0.4%max. Ca:0.1%max. Size:10-100mm,90%min. In plastic woven bags of 1 mt each.
Silicon metal #3303 Si:99.0%min. Fe:0.3%max. Al:0.3%max. Ca:0.03%max. Size:10-100mm,90%min. In plastic woven bags of 1 mt each.
