I. Introduction
SS-300-NH3 Extractive Laser Analysis System adopts TDLAS Tunable diode laser absorption spectroscope to measure HF concentration. It adopts special heated sampling probe which is able to work in high-temperature and high dust conditions, and hot & wet sampling system with little gas loss caused by gas condensing. Compare in-situ type gas analyzer, the extractive system has the advantages of no requirement of installation conditions, easy maintenance, little pollution to mirror, suitable for dirty sampling point with high dust.
II. Applications field
It is used to monitor NH3 after SNR or SCNR process in the waste incineration plant, power plant and so on.
IV. Features
1.Extractive sampling method
2.Easy calibration and calibration
3.Adopts TLDAS principle, little cross-sensitivity,
4.Laser detector with long lifespan
5.Optional sampling probe calibration function.
6.IP 65 protection class.
7.Adopts hot and wet sampling and gas pretreatment with temperature 190, preventing HCL gas loss by condensation.
8.Sampling probe with purging function.
9.With lens blow up function, to prevent it dewing.
I. Introduction
The SS-700 process VOCs monitoring system is based on the standards of HJ/T80, HJ/T75, HJ/T76 and other related standards, sampling by extraction method, configuration based on advanced gas chromatography, mass spectrometry separation technologies and hydrogen flame Ionization Detectors (FID), photoionization detectors (PID) to measure the composition of volatile organic gases such as total hydrocarbons (THC), non-methane total hydrocarbons (NMHC), aromatic hydrocarbons, esters, etc. According to the composition and detection requirements in the analysis project, it can be configured to meet the requirements of the analysis project and the frequency of analysis. At the same time, the optimization of instrument configuration can be performed to maximize the use of the instrument and ensure the continuity of sample analysis. reliability.
The analysis system fully considers sample gas conditions, dew point and other factors, and specifically designs the pretreatment system to prevent the crystallization of components in sample gas from condensing and changing the concentration of components.
The instrument uses special column combination, center cutting and back blowing technology and hydrogen flame ionization detector (FID) technology for detection. The FID Hydrogen Flame Ionization Detector is a typical mass detector that measures the mass change rate of a component in a GC gas. The response value is proportional to the mass of a component entering the detector per unit of time.
II. Features
1.The system piping is imported clean stainless steel pipe to reduce adsorption;
2.The system adopts full calibration to eliminate the influence of a small amount of adsorption on the measurement.
3.The analytical method is consistent with the calibration method, and it is detected by GC-FID method.
4.The whole process of high-temperature 180 °C with hot sample transmission, high temperature FID detection, to avoid high-boiling VOCs adsorption and condensation, more accurate measurement;
5.Continuously run maintenance-free design, start-up automatic cycle operation, real online analysis;
6.The whole flow path insulation design is 180°C, no water vapor condensation, to avoid corrosion degradation of parts, suitable for high temperature / high humidity / corrosive conditions;
7.Non-methane total hydrocarbons and simultaneous monitoring of benzene, toluene, xylene and other components
III. Application fields
It is used for on-line monitoring of organized organic waste gas emissions from chemical, printing, pharmaceutical, rubber, spray coating, electronic semiconductor, synthetic leather, organic waste gas recovery.
I. Introduction
SS-2000-HG mercury emission monitoring system for flue gas is a combination of the world's advanced online analytical technology and China's environmental protection monitoring technology. It is based on the company's many years of accumulated experience in the field of gas analysis and adopts multi optical path UV atomic absorption method. The system consists of a sampling unit with heat trace, a valence converter, and an analysis and processing unit. It can realize continuous on-line automatic and accurate measurement of mercury from fixed sources of flue gas. The system uses Cold Vapor Atomic Absorption Spectrometry (CVAAS), which is the most mature and stable analytical method among many mercury analysis methods. This method can only analyze the elemental mercury (Hg0) in the vapor state. CVAAS is based on the principle of selective absorption of ultraviolet light with a wavelength of 253.7 nm using mercury vapor. The low-pressure mercury lamp emits ultraviolet light through a gas chamber filled with sample gas and directly monitors the transmitted light intensity with an optoelectronic receiver to calculate the absorbance. Within a certain concentration range, the mercury concentration is proportional to the absorbance, which is in accordance with Beer-Lambert law. At the same time, oxygen, temperature, pressure, flow rate, humidity and other parameters can be monitored. Charts are generated through the data acquisition and processing system, and data remote transmission interfaces are reserved. The monitoring data can be transmitted to all levels of environmental protection according to the HJ/T212 national standard communication protocol. department.
1. Introduction
SPF223 sampling probe used in the systems for gas sampling, filtration and heating function, can effectively prevent the condensation of gas samples collected, unique structural design allows for a sampling system is more reliable, more small gas loss rate to ensure system stability and true
2. Features
The device and the part of the sample contact are all made of 316L stainless steel material processing, high temperature resistance, strong corrosion resistance. With rain cover can do outdoor work environment.
Adopting the isothermal heating body, in the design of compact structure, stable heating temperature.
Filter element is made of sintering titanium alloy which has big filter area, high accuracy, small air lock, and can be replaced from the device pulled out completely, simple operation, without tools, greatly shorten the maintenance time, and reduce the labor intensity.
Optionally providing a reusable purging / calibration port.
Operation is simple, with low temperature alarm.
The filter replacement without tools.
The switch is convenient, with locked cover.
High efficiency filter cleaning system.
3. Specifications
Maximum sampling temperature: 300
Maximum working pressure: 6BAR
Sampling chamber heating temperature: 140 (factory set, adjustable temperature)
Power supply: 220VAC 50/60Hz max 500W
Environment temperature: -20~80
Maximum dust load: 100g/m3
Filter accuracy: 5μm (other precision optional, 1-10 m)
Filter size: 150*35mm
Purging gas interface: OD8/6mm connector
Sample gas outlet: OD8/6mm connector
The sampling pipe containing: 25 * 1200mmlength is optional
Flange size: DN65PN6
The installation of accessories: installation flange & fixing bolts & flange sealed pad
1. Introduction
Sampling heated tube is one important part of the environment protection monitoring system, widely used for SCNR, SNR, waste incineration and other emission sampling.
2.Specifications
Gas pipe material: PVDF, PTFE, 316L, PFA
Black knit anti-scratch layer
Air tube size: OD8/6mm,OD6/4mm (optional)
Power consumption: 10-100W/M (depending on heating tempeature)
Power supply: 220VAC 50HZ
Sample gas heated temperature50~220
No breakpoint and cold point all the way
Using temperature controller to control heating temperature precisely
Excellent heat preservation effect
Heated tube external diamete: OD38±2mmOD42±2mm
Minimum bending: 0.5m
Lowest working temperature: -20
Minimum installation distance: vertical 2m, horizonal 4m.
2156 Scientific Instruments Suppliers
Short on time? Let Scientific Instruments sellers contact you.
1. Introduction
ECM1/2 series gas condenser is used in the sample gas pretreatment system to remove moisture from the sample. Precise measurement of gas composition means sample gas under dew point can be stable even under bad environment. ECM condenser is to improve measurement precision and life span.
2. Features
Perfect design, only one component: compressor
Two-loop system
Two-loop heating exchanger
Constant temperature adjusting system with patent
With temperature display
Temperature alarm
Dew point stability: 0.2
Environment protection refrigeration without Freon
3. Specifications
1.Ambient Temp045 6.Dew point Temp4Factory set
2.Temp Control Accuracy±0.27.Power supply220VAC 50/60Hz
3.Gas Inlet Temp80 8.Voltage300V, fuse10A
4.Gas flow rate300L/h 9.IP gradeIP20
5Warming-up Time15 min 10.Installationwall mounted or 19?�rack
I. Introduction
SS-UV-300 flue gas analyzer (low emission monitoring) based on years of experience in research and development of flue gas analyzer, combined with the field practice of nearly ten thousand successful application cases. A number of techniques of the flue gas analyzer (standard form) are upgraded (many times return room to increase gas absorption optical path, and higher accuracy of spectrometer, convection heat transfer core module temperature control, etc.).
The analyzer is based on DOAS and chemometric algorithms (PLS), able to measure concentration of gases including SO2, NO2, NO, O2, NH3, Cl2, O3, H2S, CH3I, etc. It has features of high measure accuracy, outstanding reliability, fast response time and wide applicable scope. All indexes reach or exceed those of domestic & foreign similar products, and fully qualify measurement technology index of low emission monitoring occasions.
II. Application fields
It mainly used for industrial boilers, industrial furnaces emissions monitoring in power plant, iron & steel factory, cement plant and son.
III. Specifications
Model Standard Low Emission Ultra-low Emission
Range 0-300-3000ppm 0-100-300ppm 0-20-100ppm
Linearity ±1.5%F.S.
Repeatability ±0.5%F.S.
Zero Drift ±2%F.S/7d
Span Drift ±2%F.S/7d
Response time(T90) 10S 30S 30S
Working Temp -10-+40
Preheating time No preheating Approx.10 min
Sample Gas Interface 6
Sample Gas Flow 0.5-2L/minFluctuation
I. Introduction
The analyzer is based on NDIR (Non-dispersive Infrared) technology able to measure concentration of gases including CO,CH4,CO2,SO2,NO etc. It has features of high measure accuracy, outstanding reliability, fast response time and wide applicable scope. All indexes reach or exceed those of domestic & foreign similar products, and fully qualify measurement technology index of low emission monitoring occasions.
II. Application fields
It mainly used for industrial boilers, industrial furnaces emissions monitoring in power plant, iron & steel factory, cement plant and son.
SMT spare parts X 8mm Dual Smart Feeder 00141269-03 for siemens smt pick and place machine
SMT spare parts X 8mm Dual Smart Feeder Product Details:
Siemens/ASM Siplace X 4mm feeder 00141268
Siemens/ASM Siplace X 8mm feeder 00141270 00141290 00141370 00141390
Siemens/ASM Siplace X 2x8mm feeder 00141269 00141289
Siemens/ASM Siplace X 12mm 00141271 00141291 00141371 00141391
Siemens/ASM Siplace X 16mm 00141272 00141292 00141372 00141392
Siemens/ASM Siplace X 24mm 00141273 00141293
Siemens/ASM Siplace X 32mm 00141274 00141294
Siemens/ASM Siplace X 44mm 00141275 00141295
Siemens/ASM Siplace X 56mm 00141276 00141296
Siemens/ASM Siplace X 72mm 00141277 00141297
Siemens/ASM Siplace X 88mm 00141278 00141298ABOUT US
GOLDLAND ELECTRONIC TECHNOLOGY CO., LTD focus on global Surface Mount electronic assembly sector for 10 years. We mainly provide competitive price and high quality products for various brands of SMT equipments, SMT feeders, SMT nozzles, SMT feeder spare parts, AI equipments, AI spare parts and other related products. The brands is: FUJI, KEM, PANASERT, YAMAHA, JUKI, Hitachi, Universal, Siemens, I-pulse, Assembleon, DYNAPERT, TDK and so on
Explore is the newest generation hand held xrf analyzer, it is the best hand held XRF analyzer with many features that you cant find in the markets and other brands
The features of Explores are as below:
1. Best SDD detector in the world:it equiped with the best SDD detector-fast SDD detector, that enable to analyze light elements directly without helium asist from Mg U
2. more powerful data library:it can test rare earth elements and enable to test 34 elements simultantaneously
3. more safety design, there is insurance lock key to gurantee the safety for operator and invoid mis operate
4. non power off design, the analyzer works 5 minutes even you take the battery off the analyzer, which offer you enough time to change battery and finish testing once the battery power off
5. 3 color light system: there are green, red and yellow light system to show you the working status of the analyzer
6. operator and expert mode system easy to switch
7, 3 seconds fast scan for metal alloy and stainless steel
Size (open) L110cm*W240cm*H44cm
Equipped with drone self-stabilizing system Yes
Equipped with runaway safeguard Yes
Equipped with GPS system Yes
Max. Speed 100 km/h
Drone Payload 8KG
Endurance time without load 22-23 mins
Endurance time with load 15-18 mins
Max. suspension stop time 30 mins
Battery capacity 16000 mAh
Battery life Charge/discharge 200-300 times
Max. remote control distance 1 km
Max. flying height 2 km
Application Hanging powerlines,bridge ropeways
Wind loading rate Level 6
Flying height 0-20m
The function of electricity wire installing drone:
1. The drone has accurate GPS positioning, and precise to ±1m in landscape orientation, and ±0.5m in portrait;
2. When the drone canâ??t get the remote control signal, it will enter into automatic protection mode which will let it be in suspension stop immediately. When there is no signal more than 20 seconds, the drone will return and land at the take-off place based on the GPS navigation system;
3. You can control the drone fly to any direction you want, no matter which direction the head towards to at this moment;
4. Under the straight mode, the drone will fly forward in a straight line;
5. The drone, with the function to fix the place for going back, can return to the take-off point automatically after the task is finished;
6. With protection function for low voltage. Once the voltage is lower the preseted, the lights will flicker to remind.
Advantages:
1. Made of carbon fiber material in aviation field, with reasonable design in aircraft and excellent performance in anti-impact; Foot stand is easy to retract;
2. Special design for high beam, and easy to be tracked;
3. With voltage indication function, more convenient for user;
4. Equipped with sealing motor, dustproof and waterproof;
Size (open) L110cm*W240cm*H44cm
Equipped with drone self-stabilizing system Yes
Equipped with runaway safeguard Yes
Equipped with GPS system Yes
Max. Speed 100 km/h
Drone Payload 8KG
Endurance time without load 22-23 mins
Endurance time with load 15-18 mins
Max. suspension stop time 30 mins
Battery capacity 16000 mAh
Battery life Charge/discharge 200-300 times
Max. remote control distance 1 km
Max. flying height 2 km
Application Hanging powerlines,bridge ropeways
Wind loading rate Level 6
Flying height 0-20m
The function of electricity wire installing drone:
1. The drone has accurate GPS positioning, and precise to ±1m in landscape orientation, and ±0.5m in portrait;
2. When the drone canâ??t get the remote control signal, it will enter into automatic protection mode which will let it be in suspension stop immediately. When there is no signal more than 20 seconds, the drone will return and land at the take-off place based on the GPS navigation system;
3. You can control the drone fly to any direction you want, no matter which direction the head towards to at this moment;
4. Under the straight mode, the drone will fly forward in a straight line;
5. The drone, with the function to fix the place for going back, can return to the take-off point automatically after the task is finished;
6. With protection function for low voltage. Once the voltage is lower the preseted, the lights will flicker to remind.
Advantages:
1. Made of carbon fiber material in aviation field, with reasonable design in aircraft and excellent performance in anti-impact; Foot stand is easy to retract;
2. Special design for high beam, and easy to be tracked;
3. With voltage indication function, more convenient for user;
4. Equipped with sealing motor, dustproof and waterproof;
5.Lifelong after-sale, more professional.
Features
* Nice appearance and innovative design
* LED illuminator around lens
* Imported lens with plated layer
* 5.0 Mega pixels high resolution Korea sensor * Special DSP image processor, Optical Image Stabilizer
* Single/Dual lamp control.
* Single capture button and digital pause capture.
* Adjustable focus to give clear image.
* Auto white balance and contrast adjustment, Color Temperature Filter
* Dual image compare function
* 3D-Negative capture mode
* Compatible with iris lens, hair lens and skin lens.
* Deliver clear and accurate images.
* Easy to operate.
* Maximum resolution: 2560x1920
Since 2011, Orientjohn has been a leader in the design, manufacturing, and customization of telescoping poles. With over a decade of experience, we combine innovative design, advanced production techniques, and rigorous quality standards to deliver reliable solutions for demanding applications. Our Heavy Duty Telescoping Pole is engineered to meet the toughest requirements, offering durability, versatility, and ease of use for various industries and professionals.
Fruit Picker Telescopic Pole by Orientjohn
Established in June 2011, Orientjohn specializes in the design, development, and production of telescopic poles. With over a decade of expertise, more than 10 proprietary patents, and cutting-edge manufacturing capabilities, we deliver high-quality products and customized Telescopic Tool solutions that meet the unique demands of various industries.
Our semi-automated production lines ensure an annual capacity of over 1 million poles, combining efficiency with exceptional quality control to meet the growing demands of global markets.
Product Features: Fruit Picker Telescopic Pole
The Fruit Picker Telescopic Pole is engineered for efficient and safe fruit harvesting, providing a practical solution to common challenges faced in agriculture and gardening.
Product descriptions from the supplier
Overview
Metallurgical Microscope
Specifications
Model
JX-200E
Optical system
Finite color corrected optical system
Viewing head
Gemel trinocular,45 °inclined,Diopter adjustment ±5 for each side,Interpupillary distance adjustable between:54-75mm,refract rate,binocular : trinocular =80%:20%
Eyepiece
High eyepoint wide field plan eyepiece PL10X/18mm
High eyepoint wide field eyepiece WF15X/13
High eyepoint wide field eyepiece WF20X/10mm
Objective
LWD plan achromatic metallurgical objective 5X,10X,20X,50X,100X
Nosepiece
Reversed quadruple nosepiece
Reversed quintuple nosepiece
Focusing
Low position coaxial coarse and fine adjustment. With tightness adjustment. Coarse adjustment range 38 mm;precision of fine adjustment:2um
stage
Three-ply mechanical stage,area 180mmX155mm,right hand low position control,Moving range:75mm 40mm; Metal stage plate,center hole dia.�?12mm
Illumination
Reflection Koehler illumination with iris diaphragm and center able field diaphragm , wide-range voltage 90-240V ,6V/30W halogen bulb(single 3W LED option), with continuous intensity
Polarizing kit
Polarizer and the analyzer can be removed from the optical path, the analyzer can be rotated 360 .
