Dithiodicaprolactam, N,N’-Dicaprolactamdisulphide.
Data sheet attached.
Data sheet attached.
Tetramethylthiuram disulfide.
Tetrabenzylthiuram disulfide.
Data sheet attached.
Mercure DCBS.
N-tert-butyl-2-benzothiazolesulfenamide.
Zinc diethyldithiocarbamate.
Zinc dibutyldithiocarbamate.
This vertical rubber cutter is mainly used to cut the natural rubber, synthetic rubber, and other plastics materials, especially it is suitable to be installed near the rubber mixer to cut small piece of rubber. This vertical rubber cutter mainly consists of rubber knife, frame, cylinder, base, auxiliary table, hydraulic system, and electric system. The nylon plate is installed on the base under the cutting knife for protecting the edge of the cutting knife. When cutting the raw rubber, put the raw rubber under the rubber knife, then press the start button, the knife can cut the rubber. Two limit switches are installed on the frame to control the reversal valve to change the movement direction of the rubber knife, at the same time it protects the cover of the cylinder. Wooden case for usual size
Mould size: length 215mm with 3 cavity; Heating capcity:1000w each mouldating can finish within 20min. Length:1020mm Height:1900mm Width: 960mm.
Primary parameter of which as following:tansferring volume:150cc/180cc;transferring strength :27tons; Transferring manner: from bottom to top; heating platen size:300300 and 300400; heating platen material :45steel.This type of machine is very good , primary advantage of which as following: heating temp.Is very uniform; transferring speed and volume can be easily controlled and cycle running is soomth;structure of machine is very compact , simple and pretty and by which people can operate easily and safely. Length:1550mm, height:2620mm, width:620mm.
Waste tyre oil refining plant 1. High oil yield 2. Unique exhaust removal system 3. En-friendly.
Number Items Introduction 1 Model JZB-5 JZB-8 JZB-10 2 Raw material Waste plastic and rubber Waste plastic and rubber Waste plastic and rubber 3 Structural form Horizontal Horizontal Horizontal 4 Capacity/day About 5 tons About 8 tons About 10 tons 5 Pressure Atmospheric Atmospheric Atmospheric 6 Rotate speed of the reactor 0.4R/min 0.4R/min 0.4R/min 7 Cooling form Water Water Water 8 Heating form Direct Direct Direct 9 Installation mode Base Base Base 10 Noise db(A) 85 85 85 11 Working mode Intermittent Intermittent Intermittent 12 Size of reactor 2200¡Á6000 2200¡Á6600 2600¡Á6600 13 Volumeof reactor 16 m3 19 m3 23m3 14 Weight of reator About 5 tons About 5.5 tons About 6 tons 15 Production cycle 12 days 12 days 12 days 16 Installation cycle 12 days 12 days 12 days.
ITEM CONTENT 1 MODEL PYROLYSIS PLANT LY-15 (CONTINUOUS) LY-18 (CONTINUOUS) LY-20 (CONTINUOUS) LY-22 (CONTINUOUS) 2 RAW MATERIAL waste plastic, waste rubber waste plastic, waste rubber waste plastic, waste rubber waste plastic, waste rubber 3 STRUCTURE Horizontal rotation Horizontal rotation Horizontal rotation Horizontal rotation 4 16-HOUR HANDING CAPACITY/PER BATCVH 3-4 tons of raw material 5-6 tons of raw material 6-8tons of raw material 8-10 tons of raw material 5 16-HOUR OIL PRODUCTION 1.2-1.6 tons of fuel oil 2-2.4 tons of fuel oil 2.4-3.2 tons of fuel oil 3.2-4 tons of fuel oil 6 WORKING PRESSURE Room pressure Room pressure Room pressure Room pressure 7 HOST SPEED 0.4r/m 0.4r/m 0.4r/m 0.4r/m 8 POWER 3.0KW 4.0KW 4.0KW 5.5KW 9 COOLING Water cooling Water cooling Water cooling Water cooling 10 COOLING WATER CONSUMPTION 3 4 6 8 11 TRANSMISSION Internal gears Internal gears Internal gears Gears 12 HEATING MODE Directly heating Directly heating Directly heating Directly heating 13 INSTALLATION(T/H) Have basis Have basis Have basis Have basis 14 NOISE DB(A) ¡Ü85 ¡Ü85 ¡Ü85 ¡Ü85 15 HOST DIMENSIONS 1500x6000 1800x6000 2000x6000 2200x6600 16 WORKING FORM Continuous operation Continuous operation Continuous operation Continuous operation 17 HOST WEIGHT (T) 15 17 19 22 18 EQUIPMENT MANUFACTURING CYCLE 20 days 20 days 20 days 20 days.
Targets of chemical - SVR 3l management of rubber by TCVN 3769:2004. 1. Concentrations of contaminants retained on the 45m sieve,% m / m, not more than: 0.03 2. Ash,% m / m, not more than: 0.50 3. Nitrogen content,% m / m, not more than: .60 4. Volatiles content,% m / m, not more than: 0.80 5. Early plasticity (Po), not less than: 35 6. Maintain the viscosity index (PRI), not less than: 60 7. Lovibond color index, the form, not more than: 6 8. Mooney viscosity ML (1 '+ 4') 1000C. 33, 33kg/loose bale/ load on 20'DC container/20mts.
Targets of chemical - management by the rubber SVR 10 TCVN 3769:2004. 1. Concentrations of contaminants retained on the 45m sieve,% m / m, not more than: 0.08 2. Ash,% m / m, not more than: 0.60 3. Nitrogen content,% m / m, not more than: .60 4. Volatiles content,% m / m, not more than: 0.80 5. Early plasticity (Po), not less than: 30 6. Maintain the viscosity index (PRI), not less than: 50 7. Index Lovibond color, form, not more than: - 8. Mooney viscosity ML (1 '+ 4') 1000C. 33, 33kg/loose bale/load on 20'dc container/20mts.
1. Concentrations of contaminants retained on the 45m sieve,% m / m, not more than: 0.16 2. Ash,% m / m, not more than: 0.80 3. Nitrogen content,% m / m, not more than: .60 4. Volatiles content,% m / m, not more than: 0.80 5. Early plasticity (Po), not less than: 30 6. Maintain the viscosity index (PRI), not less than: 40 7. Index Lovibond color, form, not more than: - 8. Mooney viscosity ML (1 '+ 4') 1000C. 33, 33kg/loose bale/load on 20'dc container/20mts.
Acten Turnkey Project offers our customers complete transfer of technical know-how from formulationg design, mixing technique, on-site training to quality control. We are able to help our customers in obtaining the state-of-the-art mixer and know-how, to supply quality masterbatch for the industry. We have discovered a need to offer our customers an alternative to manufacturing Masterbatch by supplying pre-formulated and pre-mixed Masterbatch, tailored according to cost and performance. In order to achieve this, we have engaged the services of specialist custom compounder in Malaysia renowned for supplying the new tyre industry. The complete plant equipments include: 1. Feed Stock Hydraulic Cutter 2. Kneader (with different capacity) 3. Roll Mill (with various sizes and usage) 4. Batch-off Machine 5. Rotary Cutter.
