ESBR is the most manufactured synthetic rubber in the world. It's shape is irregular because of the fact that there is no crystallization. Emulsion Styrene Butadiene Rubber is the most widely used rubber in the world, representing about % 40 of the synthetic rubber market which is a result of its excellent balance of properties and cost performance. ESBR has good mechanical properties, abrasion and tear resistance, being largely used in tire, retread, footwear soles, hoses, tubes, cables, conveyor belts and a great variety of moulded, calendered and extruded rubber goods. Oil Extended and Non Oil types of ESBR in the shapes of Prime, Near to Prime and Off Grades can be supplied. Near to Prime and Off Grade materials have more different properties than thier prime grade's about usually mooney viscosity but the materials have special techinical data sheets. The material's preferability reason is cheaper than their prime grade's. Cold Types Cold Oil Extended Types Main Applications 1500 1712 Tire manufacturing 1502 Automotive 1507 Mechanical Rubber Goods, Footwear & Gaskets
EPDM denotes a terpolymer based on three monomers: ethylene, propylene and a non-conjugated diene; EPDM grades have a residual unsaturation in the side chains and can therefore be cured with sulphur and accelerators. EPM represents a copolymer from ethylene and propylene monomers; EPM is entirely saturated and therefore requires vulcanization by radiation or products that release free radicals, such as organic peroxides. Its heat resistance is distinctly better than that of Natural Rubber, SBR and Butadiene Rubber. The molecules of both EPM and EPDM have a completely saturated hydrocarbon backbone, through which excellent ozone resistance and very good resistance to heat and oxidation are achieved. Oil Extended and Non-Oil types of EPDM in the shapes of Prime, Near to Prime and Off Grades can be supplied
Nitrile Butadiene Rubber which is one of the Synthetic Rubbers is manufactured by emulsion-polymerizing acrylonitrile and butadiene in low temperatures. Mainly NBR`s usage areas are seal and gasket manufacturing, fuel and hydraulic hose manufacturing, conveyor belt manufacturing, worker boat`s manufacturing, rubber rollers manufacturing and shoe soles manufacturing etc. The reasons for preference are; Very good resistance to mineral oils, greases and fuels, Good resistance to aging temperature resistance, High resistance to wear and abrasion, Low permeability to gases, Good dynamic fatigue resistance, Reasonable cost level, Good ozone resistance and conventional molding techniques Bale and powder packing types of NBR in the shapes of Prime, Near to Prime and Off Grades can be supplied.
Latex is a sticky, milky colloid drawn off by making incisions in the bark of the Par rubber tree (Hevea brasiliensis) and collecting the fluid in vessels in a process called tapping. The latex then is refined into rubber ready for commercial processing. In major areas, latex is allowed to coagulate in the collection cup. Concentrated Latex is derived from Field Latex and is processed using centrifuge methods. It contains 60% Dry Rubber Content (DRC). There are two main types of Concentrated Latex available in the market: High Ammonia or Standard Ammonia Concentrate (HA Latex) and Low Ammonia Concentrate (LATZ).
Product: Natural Latex Rubber HA 60% DRC Packing: + 200kg/ Drum, 98 drums = 19.6 tons / 20DC + Flexi-bag: 21MTs VFA: max 0.035 MST: 650 - 1000 (as customer requirement) Color: Milky White
Rubber Tariff Code is. 4001220000 Natural Rubber SGR-10 FOB Price Per Metric Tonne USD 3,075 USD 3.75 per Kilo. 1. One 20 container contains 20,160 Kgs. of Natural Rubber SGR-10 (16 pallets per container) 2. The product is packaged in free wood pallets. (Pallets of 36 bales each weighing 35 Kgs. Total Weight 1260 Kgs. each pallet). 3. Material of Pallets is: Plastic
We Manufacture & Export All Types Of Rubber Compounds, For More Information Please Write To Us At.
Rubber Granulates Size: 2-5mm In big-bags on pallets 100% Whole truck tyre material
Size 130x240 cm. Thickness 15-35 mm.
In our town we can provide every month 60 tons of raw rubber (latex and rubber cup lumps) however, we are not capable collecting all of it and shipping the product since we lack finance or budget. I would like to invite your company to establish a factory here for your rubber needs as a partner. Helping your company to have a sustainable source and also helping my town. Hope you find this offer as an opportunity. Thank you.
Rubber for Automotive industry working on iron, metal, aluminium, magnets
Type : Centrifuged Latex DRC 60%HA Product Code : HS : 4001 Total Solid Content: 61% min Dry Rubber Content : 60% Min Non Rubber Solids: 1.7% max Alkalinity: 0.6% min MST: 650 min VFA: 0.06 max KOH: 0.7 max
KEY FEATURES: 1. High transparence 2. High tensile strength 3. Good rebound property 4. Outstanding resistance to ageing 5. Low shrinkage 6. Non-discoloring 7. Excellent thermal and cold stability APPLICATIONS: The series are suitable for making baby nipples. PACKAGING: It is available in 20kg pails of 200kg drums TYPICAL PROPERTY: Appearance: Transparent; Viscosity (mpas): 650,000~950,000; Hardness: 20~70 Shore A; Tensile Strength: 6.5~8.5 MPa; Tear Strength: 20~35 KN/m; Elongation at break: 330%~800%; Linear shrinkage: 0.1% REMARKS: The product should be closed tightly, protected from light and moisture, the shelf life is 12 months These figures are for reference only, please contact us for detail. 20 KG/drum
KEY FEATURES: 1. High tensile strength 2. Good rebound property 3. Outstanding resistance to ageing 4. Low shrinkage 5. Low yellowing 6. Excellent thermal and cold stability APPLICATION: The series are suitable for making silicone kitchenware. PACKAGING: It is available in 20kg pails of 200kg drums TYPICAL PROPERTY: Appearance: Transparent; Viscosity (mpas): 650,000~950,000; Hardness: 20~70 Shore A; Tensile Strength: 6.5~8.5 MPa; Tear Strength: 20~35 KN/m; Elongation at break: 330%~800%; Linear shrinkage: 0.1% REMARK: The product should be closed tightly, protected from light and moisture, the shelf life is 12 months. These figures are for reference only, please contact us for detail. 20 KG/drum
Rubber EPDM color granules for playgrounds, production of plates, 1-3,5 mm, 0,5-1,5 mm other colors, packing BB or paper octabines
Bright Future Tyre Recycling Factory Lab Test Test Date : 26/02/2018 Type : 320 S No. Standard Requirement Our result 1 Heating loss (also called volatile matter) Max. 1.2% 0.36% 2 Ash Max. 15% 7% 3 Acetone extract Max. 28% 17% 4 Density (also called specific gravity) Max. 1.35 Mg/m3 1.20 Mg/m3 5 Mooney ML100 (1+4) Max. 85 70 6 Tensile strength (curing condition: 145x10min) Min. 6.5 MPa 10.4 MPa 7 Elongation (curing condition: 145x10min) Min 300% 325%
Various ionic forms of styrene butadiene latex emulsifying asphalt modifier Application field Various ionic forms of styrene butadiene latex emulsifying asphalt modifier are mainly used in the adhesive layer of road engineering, sealing layer, modified dilute slurry sealing layer and micro-surface, bridge deck waterproof bonding layer, waterproof coating of building waterproof engineering, waterproof ointment and other aspects. Product features Various ionic forms of butadiene latex emulsifying asphalt modifier, is a stable emulsion synthesized by high polymer material under the condition of low temperature, it is developed according to the properties of modified emulsified asphalt. The temperature sensitivity of asphalt can be significantly improved by emulsion asphalt modified with butadiene latex, low temperature property, adhesion property, crack resistance and aging resistance can be improved. Waterproof rubber spraying quick-setting latex can significantly improve the spraying quick-setting rubber asphalt waterproof coating after curing of heat resistance, bonding strength, low temperature flexibility, tensile properties and the puncture resistance after the coating film, It amends the coating after curing, such as its resistance to puncture and poor elastic recovery.
Special SBR styrene butadiene rubber asphalt modifier for waterproofing New product introduction In order to pushing the industry development, improving product quality, meeting with the demand of customers. HaiFang Rubber Technology developed XYF - ( item no. 095) styrene-butadiene rubber modifier in 2019. It grafted based on the latex and in particles form. In order to guarantee the high content at the same time, compared with normal SBR products, it can be dissolved without using colloid mill and the dissolution time is shorter. As a new kind of environmental protection material. Its main advantages: Lower melting temperature, reducing production cost, greatly reducing the dust while feeding compared with normal SBR powder. Product features 095 Waterproof SBR styrene butadiene rubber asphalt modifier is made by a certain amount of styrene in SBR styrene butadiene latex, initiated and catalyzed reaction, the formation of SBR rubber latex with a certain degree of interposition thermoplastic. The experimental results show that the high temperature properties, tensile properties, tensile strength, bonding strength and anti-aging properties of the materials can be improved obviously by adding it. To meet different customers requirements, 095 modifier was upgraded to two different kinds of products: High and low-temperature property. High temperature performance: Cohesion strength is higher than that of ordinary SBR modifier with strong peeling strength, the softening point is 4-6 higher than ordinary SBR modifier. Recommended for using in non- curing products. Low temperature performance: It is better than the ordinary SBR modifier, low temperature index is 4 lower than the normal SBR modifier, and it has a better viscosity. Recommended using in type adhesive material. Experimental test indicator SBR modifier shape Normal SBR modifier High temperature 095 Low temperature 095 Softening point 88 95 90 -20 Continuous Continuous Continuous Ultimate temperature -26 -26 -32 75 Not flowing Not flowing Not flowing Peel strength (bonding with aluminum sheet) 1.82 2.78 2.08 Peel strength (bonding with water proofing material) 1.25 1.87 1.51 Bonding effect with aluminum sheet Remains on the aluminum sheet Viscosity lasting >2h >2h >2h Quality Index Effective constituent % Fitness 16 meshes % Molecular weight Ten thousand Binding styrene% Moisture % Mooney viscosity 95 95 22-23 22-27 2.0 75 Method of use A certain proportion of styrene butadiene rubber powder should be mixed slowly into the emulsified bitumen at 140 C-150 C. Then raising the temperature to 185 C-195 C for stirring, until the styrene butadiene rubber powder is fully mixed evenly and swollen while stirring about one and a half hour and with no distinct particles.
Solid Odorless Reclaim Rubber Softener for Producing High Tensile Strength Reclaimed Rubber The solid odorless reclaim rubber softener is shinning black. Its odor is low and the specification is high. It is an ideal replacement for coal tar oil in reclaim rubber production. It is used to produce the reclaimed rubber with a tensile strength over 10 Mpa. Specifications: Appearance Solid black Softening Point 60-70 Ash Content 0.50% 18 PAHS sum1000mg/kg
MANUFACTURER : SHANDONG MATERIAL CHINA LTD SPECIFICATION : SYNTHETIC RUBBER NBR @ ACRYLONITRILE BUTADIENE LATEX FOB : MALAYSIA COLOR : NATURAL MILK AUTHORISED DISTRIBUTOR : GAP RESOURCES (M) SDN BHD www.g4tecinvestment.com/glove_dis PRODUCTION : 200 MILLION / METRIC TONNE MOQ : 20 MT / CONTAINER PAYMENT TO : GAP RESOURCES (M) SDN BHD TERM : TELEGRHAPIC TRANSFER @ TT PRE ORDER : MOQ 20 MT @ 1CONTAINER 1. 50% TT - UPON ICPO / PROFORMA INVOICE 2. 50% TT - UPON SGS / BL
