Since 36 Years, we JAY KHODIYAR INDUSTRIES are recognized as a trustworthy manufacturer, Exporter and supplier of cast iron product. In order to manufacture high-quality cast iron our professionals employ advanced machines and utilize quality tested material procured from the authentic vendors. In addition, our clients can avail these cast iron from us at a reasonable price.
U clips , J clips , brackets , hinges , clamps
We also have interest in selling Bulk Ferro Alloys and especially Low/Medium Carbon Silico Manganese and we are already exporting these product/s. We have tied up with a manufacturer bin , Bhutan to sell their products. Products are:- Low Carbon Silico Manganese. Typical Specifications are: Mn: 55 % Minimum Si: 25-28% C: 0.2% Maximum P: 0.15% Maximum Size: 10-150 MM (90%) Medium Carbon Silico Manganese. Typical Specifications are: - Mn: 55%-60% Si: 22%-25% Max C: 0.5% Max Si: 0.05% Max P: 0.2%-0.40% Size: 10-150 MM (90%) For sure, we will be able to meet the requirements, once we get your reply
Alloy 20 is an austenitic nickel-iron-chromium alloy with outstanding corrosion resistance. Alloy 20 Olets provide strong sulfuric acid resistance. This alloy is also resistant to phosphoric acid, nitric acid, and aqueous salt solutions. Alloy 20 Olets are an excellent choice when chloride stress corrosion cracking is a concern since they resist pitting and crevice corrosion. Because the rate of corrosion can substantially increase in chloride ion-containing environments, caution should be exercised. Alloy 20 Olets may provide cost savings while outperforming typical stainless steels when compared to higher nickel-based alloys. Alloy 20 is a super-austenitic stainless steel that was developed for maximum corrosion resistance to sulfuric acid and other extreme environments where regular austenitic grades are ineffective. Hot-working and cold-working are two traditional ways of producing Alloy 20. Itâ??s also vital to determine whether or not the desired corrosion resistance can be achieved in a given environment. Alloy 20 is used in a variety of industries, including chemical processing, petrochemical and refining, marine, pharmaceutical, and food processing. End-use applications include storage tanks, mixing tanks, agitators, pump and valve parts, food processing equipment, fasteners, and fittings. Plastics and synthetic fiber manufacturing Equipment for chemical and petroleum processing, heat exchangers, and process piping
Metal scrap
SPECIFICATIONS: the following Percentage Points: Chemical Composition Carbon - 0.54 to 0.82% Phosphorus - 0.035% max Manganese - 0.60 to 1.05% As. - 0,01max of Mass share Silicone - 0.18 to 0.40% Sulphur - 0.035% max Norms - R-50 GOST-7173-75 / R-65 GOST- 8165-75 The scrap consists of R-50 (51,67 KG/m) R-65 (64,72KG/m) Used Rails shall be considered free of alloys when the residual alloying elements do not exceed Cut to 1.5 meter length (standard) 1. Technical terms: USED RAIL R50-R65 2. Specifications and Chemical Composition: Used Rail: R50 (51.67KG/Meter, GOST 7173-55), Used Rail: R65 (64.72KG/Meter, GOST 8161-75). Size & Weight: Length: 12meter ~ 12.5meter Maximum or less according tobuyerâ??s instruction; Expenses on seller Width: 5.5 inches ; Weight: 64.72Kg. No fishplates or steel pieces or bolts are attached to the used rails. All rails are clean and straight. No pitting. Only atmospheric rust No heavy rust. It is mandatory that Rails must be cut into length 1.5 meter(max.) before shipment.
The Tire derived Steel or Tire Wire Scrap is a light melting scrap obtained during the shredding and granulation process of used tires. Generally 10% - 20% of the weight of an old passenger car tyre usually consists of steel. An average shredding plant produces about 100-200 MT of steel tyre wire and its quality can vary according to technology, storing and management systems adopted by the producing plants. We can provide tire wire scrap that still contains up to 20% rubber/fiber. This percentage is detected by manual separation test. The material can be loaded loose in 40 HC container. For further details, please feel free to contact us.
We offer a wide plethora of Zinc in many forms including LME registered and non registered Special High Grade Ingots and Jumbos, cathodes, dust, foil, granules, powder, pieces, anodize activated powder, shot, and a mossy form. Zinc is a bluish-white, lustrous metal. It is brittle at ambient temperatures but is malleable at 100 to 150°C. It is a reasonable conductor of electricity, and burns in air at high red heat with evolution of white clouds of the oxide. Plating thin layers of zinc on to iron or steel is known as galvanizing and helps to protect the iron from corrosion.
We are able to supply Tin in many forms including LME registered and non registered, ingots, slabs, bars, foil, granules, powder, anodized activated powder, shot, wire, sticks, ingots, and “mossy tin”. Tin is a silvery-white metal, is malleable, somewhat ductile, and has a highly crystalline structure. The element has two colours, with a cubic structure which changes at allotropic forms. On warming it is grey, the ordinary form of the metal. When Tin is cooled below 13.2°C, it changes slowly from white to grey or tetragonal structure. This change is affected by impurities such as Aluminium and Zinc, and can be prevented by small additions of Antimony or Bismuth.
We put forward a high quality of assortment of Nickel which is available in many forms including LME registered and non registered cathodes, cut cathodes, briquettes, pellets, disks, shots, granules, foil, powder, flakes, sheet, wire, mesh, spheres, “evaporation slugs”, and rods. Nickel is a silvery white metal that takes on a high polish. It is hard, malleable, ductile, somewhat ferromagnetic, and a fair conductor of heat and electricity
We are engaged in making Lead available in several forms including LME registered and non registered 99.97% and 99.99% as well as secondary ingots, foil, granules, powder, rod, shot, sheet, and wire. Lead is a bluish-white lustrous metal. It is very soft, highly malleable, ductile, and a relatively poor conductor of electricity. It is very resistant to corrosion but tarnishes upon exposure to air. Alloys include pewter and solder.
We hold immense expertise in making available Copper in many forms including LME registered and non registered cathodes, billets, rods, cakes, bars, foil, sheet, granules, plates, powder, shot, turnings, wire, insulated wire, mesh and “evaporation slugs”. Copper is one of the most important metals. Copper is reddish with a bright metallic lustre. It is malleable, ductile, and a good conductor of heat and electricity (second only to silver in electrical conductivity). Its alloys, brass and bronze, are very important. Monel and gun metals also contain copper. The most important compounds are the oxide and the sulphate, (blue vitriol
A unique product of Aluminum briquettes made from aluminum turning Aluminum contain 90% above.
Lead slag produced from rotary furnace lead percentage is 20 to 25%
mporter & Supplier of Nickel Sludge. Our product range also comprises of Copper Ore, Tin Ore, TIn Sludge, Cobalt etc. The raw materials are available in powder form, to the exact chemical and physical (Mesh Size) specifications of the welding electrodes industry. Nickel Sludge Product Code : Nickel Nickel Percentage : 15% to 20% Payment Terms : T/T (Bank Transfer), Western Union, Other Minimum Order Quantity : 25 Metric Ton Production Capacity : 100mt Delivery Time : immidiate Packaging Details : as per costumer requirement
Aluminium dross available 30% Recovery and 98% purity with 5 to 10% pure metal.
We have established immense expertise in dispatching Aluminum Extrusions. We have Aluminum Extrusion 6063 that is without any attachments.
Waste Specification: European Classification: E46 EWC Code: 19.01.02 Basel Code: B10 10 The material is loose steel scrap processed through an incinerating plant for domestic waste followed by magnetic separation, fragmentized into pieces and consisting partly of tin coated steel cans. At a visual inspection, the material is fragmentized, with iron and steel parts, resulting partly cut or in shredded form. The stock appears heterogeneous and contains all kind of cut or dismantled steel parts such as sheets, bars, frames, wires, bolts and other iron/steel household residues. The incinerated scrap is eventually oxidized, due to the thermal and cooling treatments, that the material has been submitted to. The burnt scrap also contains minor slag parts, ash and iron oxide, due to the recovery process. Such components are inherent and adhere to the scrap surface. The total impurities, can be sorted, but not fully removed. The consignment does not contain any type of arms, ammunition, mines, shells, cartridges, radioactive contaminated, or any other explosive material in any form either used or otherwise. The collected stock, is stored in open air, on cemented flooring. Due to the scrap dimensions and the material conditions, this particular scrap, should be carefully evaluated first, by the end users, to confirm its adequate recovery ratio and its suitability to be re-melted in the electric arc furnace. Please feel free to contact us for further details
Plate Iron Scrap is a material that a visual inspection appears of regular shape. This by-product is formed after slag processing in electrometallurgical furnaces. Its chemical composition is homogeneous and stable with about Fe 90% and P around 1.4%, S 0.8% and C 1.4%. The max weight of each pieces is up to 1 ton. The material can be loaded loose in 20 heavy duty container. For further details feel free to contact us.
The Aluminium Incinerated scrap is the by-product derived from the reprocessing IBA Incinerator bottom ash). It can be classified as follows: Basel code B1010. EW Code: 17 04 02. With a low melting point at 660'C, on visual inspection, aluminium can be found as melted and re-solidified particles or rocks. This happens to aluminium foil that is converted into small droplets during the incineration process. Some larger and thicker aluminium packaging items can still be partially recognised as they retain their shape. The heterogeneous nature of the processed material is due to the diversified conditions present in the combustion chamber, (some relatively cooler regions in the furnace). The stock can contain all kind of aluminium packing. We can currently provide this material in three different fractions and with different aluminium content: 3-8 mm split in two different qualities: 65% ± 3% Al 85% ± 3% Al 8-16 mm: about 70% ± 3% Al 16-60 mm: about 80% ± 3% Al The material contains minor impurities typically stones, ash, glass. Such components are inherent and adhere to the scrap surface. The total impurities can be sorted, but not fully removed. The collected stock is stored in warehouse on cemented flooring. It can be loaded loose in 20' Feet heavy duty container.
