Medical equipment, hospital equipment, construction equipment, food like jams, saffron, citrus, minerals like clinker, sunglasses and medical glasses, soft and hard contact lenses.Exporting
The main door is made of wrought iron and with 6mm tempered frosted glass rear of teh main wrought iron design + inclusive of lock with 03 keys, eye piece, brush & tower bolts. The door is painted black powder coating and antique copper hand paint. The door will have a frame of 20cm to cover wall. 1400mmx2200mm door packed in wooden cartoon.
Galvanized gi hdg steel coils sheets slits, ppgi ppaz prepainted color coated oils sheets slits, aluzinc coils sheets, crca ms coils sheets, ms hr coils sheets plates, beams, angles, channels, wire rods, gi wire, wire mesh, cold drawn wire epoxy coated wire, pvc coated wire.
With multi-direction air flow supply, automatic swing wind, users can set auxiliary wind gap to send part of air to other place, so as to improve the indoor temperature and the air flow uniformity. System adopts big diameter vortex centrifugal fan to make running silently, and optional anion generator to make pure and fresh indoor air. Ultrathin frame, min-thickness for frame is only 260mm, users can chose installation direction for connection pipe depending on spot situation, the overall dimension for part of unit is only 590x590mm easy installation with low installation cost. Remote control is available, flexible control method. High lift water pump design (750mm); Disposal of condenser water pipes is easy and flexible. Water level switch protection ensures no water leakage, water in the discharge pan can be discharged manually; and the water holder pan is designed with discharge hole, which can discharge the remaining condenser water on time, so as to reduce the possibility for bacteria growth, meanwhile discharging dirt in the regular time reduces clogging probability for water pump. â??Câ?? type heat exchanger can aid terminal air flow and the uniformity for cooling system, the effect for 4-way air-out can be more balanced, and system leak out possibility can be lower. Hydrophile aluminum coil fin can greatly reduce condensation water remaining on the fin, therefore it reduces the windage and the effect for heat exchange is also improved. Available for BMS concentrate intelligent control system. And some more designs for easy installation including built-in water valve (optional) for easy exterior connection installation, hand protection grilling and stainless steel soft pipe connection.
TI UNIT compact roof top chiller units are manufactured in type of air cooled in capacities of 5 to 360T.R. in one to four circuited configurations. In all TI UNIT compact roof-top chiller units the frames and body are from galvanized steel & stainless steel (316l) (option) the chassis made steel channel in appropriate thicknesses and all of units are completely painted in the proper thickness. Evaporators are high efficiency shell and tube heat exchangers, designed based on TEMA. Condenser of compact rooftop chiller unit made of plated coil, designed based on TEMA. Chillers with plate type heat exchangers are available upon request. TI UNIT compact roof top chillers can be designed to operate with R-22, R-407C and R-134a refrigerants. Safety controls installed on all units include high, oil and low pressure cut-outs, compressor safety cut-out, water anti freeze thermostat, water flow switch and evaporator entering water thermostat and compressor operation time logger. The above mentioned are all chosen from the most recognized controls manufactures in the air conditioning industry. Automatic condensing temperature control: A controller, factory installed on each unit automatically stages the condenser fans allowing the unit to start. With this controller the condenser fans start stage by stage. Raw materials such as copper tubes, fittings and valves are supplied by well-respected manufacturers. Electrical safety measures such as three phase controller and circuit breakers are, available on all units. A fault detection system for the whole unit is available upon request. Microprocessor based PLC controller is also available as needed. Suitable accessories make the chillers operable in all seasons according to the application requirements without any problems.
Specifications of Rice baking pot Capacity of 25 kg Iranian rice and 35 kg foreign rice 2.5 mm thick welded baking compartment, polished by 316 AISI Stainless Steel with a polishing surface of at least 0.6 micron Includes pressing floor for reinforcement and ease of discharging of contents (Request for baking tank to be ordered on inquiry) Equipped with European Thermocouple Spark and burner. Includes Stainless steel 304 AISI door, tray and chassis Direct flame by Tubby Stainless Steel 430 AISI burner with low working pressure and European high thermal power. Double-walled door with air insulation, high quality pure silicone Rubber sealing (German Food Grade). Equipped with 4 door clamps 50mm thick ceramic insulation and density 128 with refractory fabric coating to reduce heat dissipation Stainless steel hinges with capability of holding doors in different modes. Equipped with a safety and resistant valve against acids and gases from combustion, include combustion chamber and stainless steel AISI 309 exhaust (fireproof grade) 2 mm thick and formed to enhance maximum combustion chamber Equipped with 2.5-inch AISI 304 Stainless Steel petcock Includes AISI 304 stainless steel frame and chassis Equipped with a pressed strainer for baking rice. There is no need to remove the strainer for rice rinse Includes filter and governor on main gas inlet View of cubic boilers with insulated and reinforced polyurethane foam Capability of using CNG or liquefied LPG Equipped with 4 adjustable legs
In all TI UNIT air handling units the frames are from aluminum profiles while the chassis and body panels are made from galvanized steel sheets in appropriate thicknesses. All units are completely painted in the proper thickness. Blower(S): Double width-double inlet centrifugal fans with forward curved blades are normally used for low pressure drop requirements as opposed to fans with backward curved blades which are for high pressure drop applications. Fans and housings are made of galvanized steel each set off a plus other related components such as shafts are statically and dynamically balanced, shafts are selected from proper material and size. Other power transmission components such as pulleys and belts are also suit ably chosen depending on the required fan speed and electric motor power. Fan(s) and the corresponding electric motor(s) are installed on an independent chassis which is itself installed on the main chassis using vibration dampers in order to eliminate transfer of vibrations to the structure. To further reduce the effects of vibrations, fan outlet (s) are also connected to the structure via flexible material such as canvous. All 380V/3/50Hz electric motors are selected with insulation class of (f) and ingress protection of (IP- 54). Electric motors with ingress protection of (IP- 55) are also available upon request. Coil (S): Cooling and heating coils or either one of the two depending on the Requirement May be installed. Cooling coils are available in two, types of chilled water and direct expansion (D.X.) as per clients requirements. The chilled water coils are constructed of 5/8 O.D copper tubes plate finned (8, 10, 12 or 14 FPI) in aluminum or copper upon request. The D.X. Coils are constructed of 3/8 OD copper tubes also plate finned (10, 12 or 14 FPI) in aluminum or copper as required. The chilled water for cooling coils in to be supplied by a water chiller and in the D.X. coils cooling is provided through the use of refrigerant such as R-22, R-407c or R-134a. Chilled water coils may be requested in 4 or 6 rows and as to the D.X. coils, they are available in 4 or 6 row configurations. Heating coils are available in two types of hot water and steam. The hot water coil similar to chilled water coil is offered in 1 or 2 row configurations. Steam heating coils are constructed of 1/2 seamless steel pipe spiral finned in aluminum or copper. Coils in 1 & 2 -row configurations are available upon request. Mixing box: Fresh and return air streams are mixed in the mixing box .An independent air damper is included for each air stream. Air Dampers are manufactured from aluminum in opposed blade configuration and are air sealed through the use of rubber strip gasket. Damper actuators ma y be easily installed when required. Washable aluminum filter modules 2 inches in thickness are arranged in (V) type configuration inside these boxes. Housing for
