GLsun 40Gb/s QSFP+ PSM 10km Optical Transceiver is a four-channel, pluggable, parallel, fiber-optic QSFP+ transceiver for InfiniBand QDR/DDR/SDR, 10G/8G/4G/2G fiber channel. and SAS Applications. The QSFP full-duplex optical module offers 4 independent transmit and receive channels, each capable of 10.3Gbps operation for an aggregate data rate of 40Gbps 10km using single-mode fiber. These modules are designed to operate over single-mode fiber systems using 1310 nm DFB laser array. An optical fiber ribbon cable with an MPO/MTPTM connector can be plugged into the QSFP module receptacle. QSFP+ PSM LR4 is one kind of parallel transceiver that provides increased port density and total system cost savings. Compatible Cisco Form Factor QSFP+ Max Data Rate 11.2Gbps Wavelength 1310nm Max Cable Distance 10km at Single Mode Fiber Connector Single MPO Transmitter Type DFB Laser Array Extinction Ratio 3.5dB Media SMF Power Consumption
Cisco QSFP-40G-LR4 Optical Transceiver are designed for use in 40 Gigabit Ethernet links over single mode fiber. They are compliant with the QSFP+ MSA, and IEEE 802.3ba 40GBASE- LR4. Digital diagnostics functions are available via an I2C interface, as specified by the QSFP+ MSA. Compatible Cisco Form Factor QSFP+ Max Data Rate 11.3Gbps data rate per wavelength Wavelength 1310nm Max Cable Distance 10km link length Connector Duplex LC Transmitter Type DFB CWDM Extinction Ratio 3.5dB Media SMF Power Consumption
GLsun QSFP-40G-SR4 Optical Transceiver is a four-channel, pluggable, parallel, fiber-optic QSFP+ transceiver for 40-gigabit ethernet applications. This transceiver is a high-performance module for short-range multi-lane data communication and interconnect applications. It integrates four data lanes in each direction with 40 Gbps bandwidth. One version is each lane can operate at 10.5 Gbps up to 100m using OM3 or 300m using OM4 multimode fiber, another version is each lane can operate at 10.5Gbps up to 300m using OM3 or 400m using OM4 multimode fiber. These modules are designed to operate over multimode fiber systems using a nominal wavelength of 850nm. The electrical interface uses a 38 contact edge type connector. The optical interface uses a 12 fiber MTP (MPO) connector. This module incorporates proven circuit and VCSEL technology to provide reliable long life, high performance, and consistent service. Compatible Cisco Form Factor QSFP+ Max Data Rate 10.5Gbps Wavelength 850nm Max Cable Distance 150m on OM4 MMF Connector MTP/MPO Transmitter Type VCSEL 850nm Extinction Ratio 4dB Media MMF Power Consumption < 1.5W Power Supply Voltage 3.3V Operating Case Temperature 0C to +70C (Commercial)
QSFP28-100G-CWDM4-T02 Optical Transceiver integrates the transmit and receive path onto one module. On the transmit side, four lanes of serial data streams are recovered, retimed, and passed on to four laser drivers, which control four CWDM with 1271, 1291, 1311, and 1331 nm center wavelengths. The optical signals are then multiplexed into a single-mode fiber through an industry-standard LC connector. On the receive side, four lanes of optical data streams are optically demultiplexed by an integrated optical demultiplexer. Each data steam is recovered by a PIN photodetector and transimpedance amplifier, retimed, and passed on to an output driver. This module features a hot-pluggable electrical interface, low power consumption, and 2-wire serial interface.
GLsun QSFP28-100G-LR4 Optical Transceiver integrates the transmit and receive path onto one module. On the transmit side, four lanes of serial data streams are recovered, retimed, and passed on to four laser drivers, which control four electric-absorption modulated lasers (DMLs) with 1296, 1300, 1305, and 1309 nm center wavelengths. The optical signals are then multiplexed into a single-mode fiber through an industry-standard LC connector. On the receive side, four lanes of optical data streams are optically demultiplexed by an integrated optical demultiplexer. Each data stream is recovered by a PIN photodetector and transimpedance amplifier, retimed, and passed on to an output driver. This module features a hot-pluggable electrical interface, low power consumption, and 2-wire serial interface. Compatible Cisco Form Factor QSFP28 Max Data Rate 28Gbps data rate per wavelength Wavelength 1310nm Max Cable Distance 10km link length Connector Duplex LC Transmitter Type LAN WDM DML Extinction Ratio 4dB Media SMF Power Consumption
GLsun QSFP-100G-SR4 Optical Transceiver is an integrated transceiver module containing a micro-optic component and semiconductor material, and can implement optical-electrical conversion and electrical-optical conversion. The module is designed as a four-channel, pluggable, parallel, QSFP28 transceiver for 100Gbps fiber-communication. Each channel can operate at 25Gbps up to 70m on OM3 fiber. And the operating wavelength is 850nm. The optical interface uses an 12 fiber MTP(MPO) connector, and the electrical interface uses a 38 contact edge type connector. This product is compliant to 100GBASE-SR4 of IEEE802.3bm standard and SFF-8436 specification, and provides reliable long life, high performance, and consistent service.
Application Applicable for the FTTH project and provide mechanical protection for a fiber management system that includes the functions of splicing, patching, and passive component integration. â? Rated to IP55, suitable for indoor or outdoor application. Features Easy to install and connect. Available for standard SC, or LC-Duplex adapters. Available for 1x4 or 1x8 PLC splitter. The fiber bend radius in the box is more than 30mm. Open ports for easy cable installation. Perfect fiber management - Clear fiber function division and fiberting. Reliable cables fixed device (including outputs). Available for both Wall-mount and Pole-mount.
Name:Serial to Wifi/Ethernet Converter (RS232/485+RJ45) Model:WF-01 WF-01 is a wireless networking router, which is used for project of RS232/RS485 serial equipment to WIFI or Ethernet networking. WF-01 provides a serial port to WIFI function, can be RS-232/485 converted into a TCP/IP serial network interface, RS-232/485 serial port and WIFI/ Ethernet bidirectional data transparent transmission.The serial device can transfer the data to TCP/IP network interface connect to the network for data communication, communication extended the range to serial device greatly! 1.Can use as a Router; 2.Support Hardware AP, HTTPD Client and WEB IO; 3.Suport TCPB Function; 4. Fast Access WiFi; 5.Support hardware flow control (RTS/CTS) RS232 interface, male mouth(needle) consistent with computer pin definition; 6.RS232 RS485 automatic switching; 7.Support Webpage Configuration; 8.RJ45 network connection, support wired Ethernet transmission; 9.Rich status indicator light: Power/Ready/Link/RXD/TXD; 10. Reload button, do not worry incorrect settings(in working status, press the button 3s then it load to default settings and automatic restart); 11. Design with positioning hole, convenient installation; 12.Highest support baud rate 460800 bps; 13.Optional TCP Server/TCP Client/UDP Client/ UDP Server mode, the TCP Server mode can support up to 32 Client connection; 14.Multiple applications for data transmission from wired to wireless.
WIFI Display Receiver--A9 Support Miracast, DLNA, Airplay. These three modes synchronize or project photos, videos, music, office files, etc. from iPhone/Android smartphone/tablet to a large screen. The HD 1080P video output and high-quality audio output of the monitor give you a different audio-visual feast. Easy to use: Plug and play, enjoying media on the big screen. 3 steps: Plug -> Connect -> Mirroring. The connection method varies depending on the phone model. Compact design, ideal for presentations in office or school. At home, you can easily cast small screen to big screen, giving you theater-like enjoyment. Packaging Details: * Color box, gift box, blister packing or any other packing * Standards: Carton * OEM packing is warmly welcome
DAKSH CCTV INDIA PVT LTD - 32 CHANNEL NVR , ALL CH UPTO 8 MP REAL TIME RECORDING , 2 SATA * 6 TB ; P2P , MOBILE APP: SUPER LIVE PLUS NVR Cramped up with storage issues? The Network Video Recorder a hardware with optimized Operating system that processes the image in the camera itself and sends it to a mass storage device which makes storage hassle free.
1.For anti-UAV, forced landing and drive mode are adopted 2.Target at the designated position 3.Manual \ automatic adjustment of strike frequency band and power 4.Flexible customized interference mode, automatic start and stop 5.The electronic map shows the working status and strike area in real time 6.Guided by UAV radar, UAV Radio Monitoring Equipment, Optoelectronic Device and other equipment 7.Equipment self-check, abnormal report 8.Standard interfaces and protocols for secondary development components Product Description: ZY-JKFZ-EIM025P Portable Jammer can launch multi-band electromagnetic wave to counter the interference of UAV, and can quickly make forced landing or drive away low-altitude UAV, so as to realize effective control of "black flight" UAV. This jammer device is portable, easy to operate, easy to disassemble and easy to carry. ZY-JKFZ-4010A can suppress the remote control frequency and image transmission frequency of UAVs and interfere with the navigation signal of UAVs. With high aiming accuracy and long interference distance, it can easily and quickly interfere with the black flying UAVs. Of course we can add the detection alarm function to it according to your requirement. Product Parameters: ZY-JKFZ-EIM025P: Interference intervention distance: 1km; Azimuth coverage (horizontal): 360 Host weight: 5655g; Charger weight: 300g; Telescopic sight weight: 520g; Interference band: 800-950 MHz;1550~1620MHz; 2400~2485MHz; 5720~5870MHz (Other frequency bands can be customized); Interference time: 1s; The time to perform a forced landing or return: 5s; Expand the withdrawal time: 0.2min; Environmental electromagnetic wave permissible radiation intensity: 12V/m; EMC electromagnetic compatibility: Normal; Control interface: Network/serial port; Interference type: Narrow band noise interference, broadband noise interference, frequency sweep noise interference; Power supply: AC220V/50Hz; Working Temperature: -20-55; ZY-JKFZ-4010A: Frequency range: GPS/Glonass 2400MHz 5800MHz; Strike range: 1.5km; Antenna gain: GPS/Glonass > 12dbi 2.4G> 11dbi 5.8G > 12dbi; Signal output rate: GPS/Glonass 2.4G
16-ch Analog Input Module with 2-ch Isolated DI and 1-ch DO * Protocol USB2.0 TCP/IP, MODBUS RTU, MODBUS TCP ASCII Command * Support USB2.0, 10/100 Ethernet, RS-485/232C, CAN (optional) * Fully photo-isolation 3750Vrms * Wide supply voltages (10~30V)
EDAM-9050 12 DI and 6 DO channels Digital I/O Module * Support Modbus/TCP,TCP/IP, UDP, ICMP, ARP * Ethernet 10/100 Based-T Communication * Support 6 Isolated digital output channels (NPN). * Provide Pulsed/delay Output Mode * Support 12 Isolated digital Input Channels * Provide Counter/ Frequency Inputs Mode * Support Dry Contact Inputs * Fully Photo-Isolation 3750Vrms * Status LED indicator
The SIM7600CE is Multi-Band LTE-TDD/LTE-FDD/HSPA+/TD-SCDMA/EVDO and Dual-Band GSM/GPRS/EDGE module solution in a SMT type which supports LTE CAT4up to 150Mbps for downlink data transfer. It has strong extension capability with rich interfaces including UART, USB2.0, SPI, I2C,GPIOetc. With abundant application capability like TCP/UDP/FTP/FTPS/HTTP/HTTPS/SMTP/POP3 and MMS, the module providesmuch flexibility and ease of integration for customer's application. General features * Quad-Band TDD-LTE B38/B39/B40/B41 * Tri-Band FDD-LTE B1/B3/B8 * Dual-Band TD-SCDMA B34/B39 * Dual-Band UMTS/HSDPA/HSPA+ B1/B8 * CDMA 1X/EVDO BC0 * GSM/GPRS/EDGE900/1800 MHz * Control Via AT Commands * Supply voltage range: 3.4V~ 4.2V * Operation temperature: -40�¢??to +85�¢?? * Dimension: 50.80*31*5.35mm * Weight: 5.5g * GNSS gpsOneGen 8B;standalone;assisted,XTRA; Specifications for Data transfer * LTE CAT4-Uplink up to 50Mbps, -Downlink up to 150Mbps * TD-SCDMA-Uplink up to 128Kbps, -Downlink up to 384Kbps * TD-HSDPA/HSUPA -Uplink up to 2.2 Mbps, -Downlink up to 2.8 Mbps * HSPA+ -Uplink up to 5.76Mbps, -Downlink up to 42 Mbps * UMTS-Uplink/Downlink up to 384Kbps * EDGE Class-Uplink/Downlink up to 236.8Kbps * GPRS -Uplink/Downlink up to 85.6Kbps Other features * USB Driver for Microsoft Windows 2000/XP/Vista/Win7/Win8 * USB Driver for Windows CE/Mobile * USB Driver for Linux /Android * RIL supporting for Android/Windows CE/Mobile * Automatic installationfor windows * Linux API SDK * Firmware update via USB * TCP/IP/IPV4/V6 Multi-PDP,MT PDP * FTP/FTPS/HTTP/HTTPS/SMTP/POP3/DNS/MMS * DTMF * MBIM to Win8 * Source code of the PC manager of the device for reference Interfaces * USB2.0 * UART * SIM card * SPI * I2C * Constant current sink * GPIO * ADC * PCM * SDIO
The SIM7500SA is Multi-Band LTE-FDD/HSPA module solution in a LGA type which supports LTE CAT1 up to 10Mbps for downlink data transfer. It has strong extension capability with rich interfaces including UART, USB2.0, I2C, GPIO etc. With abundant application capability like TCP/UDP/FTP/FTPS/HTTP/HTTPS/SMTP/POP3 and MMS, the module provides much flexibility and ease of integration for customer's application. General features * FDD-LTE B1/B3/B5/B7/B8/B28 * Dual-Band UMTS/HSDPA/HSPA+ B1/B5 * Control Via AT Commands * Supply voltage range: 3.4V~ 4.2V * Operation temperature: -40�¢?? to +85�¢?? * Dimension: 24*27*2.75mm * Weight: 4.0g Specifications for Data transfer * LTE CAT1 - Uplink up to 5Mbps, - Downlink up to 10Mbps * HSPA+ - Uplink up to 5.76 Mbps, - Downlink up to 42 Mbps * WCDMA - Uplink/Downlink up to 384Kbps * CSD - WCDMA data rate 57.6Kbps - WCDMA 64kbps CSD for Video call Other features * USB Driver for Microsoft Windows 2000/XP/Vista/Win7/Win8 * USB Driver for Windows CE/Mobile * USB Driver for Linux /Android * RIL supporting for Android/Windows CE/Mobile * Automatic installation for windows * Linux API SDK * Firmware update via USB * TCP/IP/IPV4/V6 Multi-PDP,MT PDP * FTP/FTPS/HTTP/HTTPS/SMTP/POP3/DNS/MMS * DTMF * MBIM to Win8 * Source code of the PC manager of the device for reference Interfaces * USB2.0 * UART * SIM card * I2C * GPIO * ADC * PCM
Industrial design, stable and reliable, suitable for harsh environment; Support 4, 8 and 16 digital DO outputs, widely used; DO1 supports PWM high-speed pulse output, frequency: 10Hz ~ 300KHz; DO2 can be used to control the direction output of stepper motor and servo motor; 1 RS485 supports Modbus master and slave protocol for expanding IO or HMI; One RJ45 Ethernet interface supports TCP Server and TCP Client services; Support Modbus TCP and MQTT protocols, can access SCADA, MES and cloud platforms; As a TCP server, it can support 5 TCP links at the same time.
1.Wide working voltage, support 9-36V DC power supply, with anti-reverse protection design; 2. Built-in industrial grade ARM CortexTM core, high performance, stable and reliable; 3. Quad band 850/900/1800/1900Mhz GSM GPRS Module inside. 4. 3G/4G/NB-IoT Modules are optional; 5. Modular design, can easily upgrade the cellular module if network upgrade; 6.Support 1 channel relay output for restart the devices; 7.Supports 1 channel RJ45 Ethernet port, built-in isolation transformer, up to 2KV electromagnetic isolation; 8.Up to 10 user's phone number to receive alarm and daily report SMS/Call; 9. Support monitoring power supply status and max. 7 network devices monitoring simultaneously; 10. Built-in TCP/IP protocol stack, support transparent transmission and Modbus RTU to Modbus TCP Protocol; 11.Inbuilt large capacity automatically rechargeable backup battery; 12. Industrial class design suitable for long time work applications; 13. Support configure parameters, load profiles and upgrade the firmware via PC; 14. Wall mount or 35mm standard DIN rail Design, convenient installation, 15. Metallic cover, small size, exterior dimension is L70*W88*H30mm.
1. Embedded 32-Bit High Performance Microprocessor MCU, inbuilt watchdog; 2. Power supply 12~36VDC with over voltage and phase-reversal protection; 3. Supports TCP Server, TCP Client, Modbus TCP, MQTT Protocols; 4. DO1 support PWM output; 5. Management and configuration via LAN connection configuration software for easy operation and maintenance; 6. 8 optical isolated digital input, supports max. 700khz high speed pulse counter; 7. 8 digital output or relay output, supports 10Hz~300KHz high speed pulse output; 8. 8 isolated analog input, 12-bit resolution, supports 0~20mA,4~20mA,0-5VDC, 0-10VDC; 9. High sampling frequency and special filtering strategy to ensure reliability; 10.1 RS485 Serial port, supports Modbus RTU Master or Slave, can extend I/O modules; 11.Supports register mapping function and extend I/O inquiry strategy; 12.Provides 1 channel 12~36VDC power source output for external device, saving wiring cost; 13.LED instructions work status, with reset button to reset, easy on-site installation and commissioning; 14.Using metal shell, protection class IP30. Metal shell and system security isolation, especially suitable for industrial applications in the field; 13.Small size, L105 * W88 * H30mm, compatible wall installation and DIN35mm industrial rail installation.
The Dual Simcard Cellular IoT Modbus RTU is design for working in the harsh industrial application environment, converting Modbus TCP/RTU to SMS and cloud platform. widely used in a variety of industrial automation, security monitoring system, automatically measurement and control system, BTS monitoring, remote data acquisition, telemetrically systems, automatically control system. It can be used as a remote switch, remote I/O, remote smart PLC, timer switches. Supports SMS,GPRS,3G, 4G Lte Cellular Networks.Compatible Modbus TCP and MQTT IoT Protocols and can intergrate to the KPIIOT IoT Cloud Platform and OPC, SCADA and MES systems.
The PLC Gateway D225 is a converter for converting the data protocol of Mitsubishi PLC into Modbus TCP RTU protocol. The D225 can store the I/O data of the PLC to the gateway through the RS-232 or RS-485 serial port of Mitsubishi PLC. The gateway transmits the data to the cloud platform through the Modbus protocol, and also allows your software to pass through the local area network anywhere. Or Internet access to serial port devices. 1.Built-in industrial grade ARM CortexTM core, high performance, low power consumption, stable and reliable. 2.Converting the data protocol of Mitsubishi PLC into Modbus TCP protocol,then connect to cloud. Support 1 channel RS-232, 1 channel RS-485 and 1 channel TTL. 3.Support 1 channel RJ45 Ethernet port 4.Support RESET button to restore factory function (long press for 3 seconds to recover) to prevent parameter setting error. 5.Using metal shell material, protection grade IP30, metal shell and system safety isolation, especially suitable for industrial control applications. 6.Using configuration software to set device parameters, support WIN XP, WIN 7, WIN 8 and WIN 10, friendly interface. 7.Support static IP address or DHCP to obtain IP address automatically, and query the devices in the network through UDP broadcast protocol. 8.Support local HMI touch screen and remote simultaneous access to PLC for data acquisition and monitoring. 9.Support server domain name resolution. Support firmware upgrade through TTL, firmware update is more convenient.
