About Steel re-Rolling Mill Steel Re-rolling is a major steel section and bar producing technology used in India and abroad. Since its inception in India with setting up of first re-rolling mill in Kanpur in 1928, this technology has contributed significant steelmaking capacity in secondary steel sector in India. Air Pollution Depending upon the fuel used in heating the furnace of a Steel Re-rolling Mill, the characteristics of flue gases may vary. For coal fired furnaces they may consist of gaseous as well as particulate pollutants. For oil or gas fired furnaces, these flue gases may consist of just gaseous pollutants. The flue gases may also be corrosive in nature. Selection of Technology for Air Pollution Control Device Selection of Technology for Equipment in an Air Pollution Control System in case of a Steel Re-rolling Mill depends upon the fuel to be used : a. Scrubber based System for Oil / Gas Fired Furnaces b. Cyclone and Scrubber based System for Coal Fired Furnaces About Scrubber based System for Oil / Gas Fired Furnaces Characteristics of Air Pollution Generated In Induction Furnace 1 Pollutants : Dust & Gases such as NO , SO , CO, Co x 2 2 2 Concentration : SPM - 1200-1500 mg/Nm (Maximum, in coal fired) 3 So - 800-1000 mg/Nm 2 4 NO - 20-50 mg/Nm x 5 Temperature : At Suction Point: 250-300 C 6 Nature of Dust : Slightly Sticky, Non Abrasive and Non Explosive Control Practices The control practice adopted in controlling air pollution in this industry mainly depends upon following parameters : 1 Dust/Gas Concentration at inlet 2 Discharge Standards 3 Temperature of Flue Gases 4 Nature of Pollutant i.e. Dust (Particulate) or Gaseous 5 Nature of Dust i.e. Sticky, Abrasive 6 Nature of Gases i.e. Corrosive, Non Corrosive Working of Equipment 1. Ducts & Bends : 2. Scrubber : 3. ID Fan : 4. Stack (Chimney) : About Cyclone and Scrubber based System for Coal Fired Furnace Working of Equipment 1. Ducts & Bends : 2. Cyclone : 3. Scrubber : 4. ID Fan : 5. Stack (Chimney) : Discharge Characteristics as Per Norms 1 Dust : Less than 150 mg/ Nm 2 Temp : Less than 80-100 C 3 Gases : Traces of SO , NO , Co , Co.
Co (carbon monoxide) is a colorless, odorless and tasteless poisonous gas that can be fatal when inhaled, which is also know as “silent killer.” it is produced when any fuel is incompletely burned because of insufficient oxygen. Wood fires and charcoal grills produce large amounts of co. Malfunctioning heating systems also produce co. It’s highly suggest to install co detectors in place like kitchen, bathroom, living room, car barn. Co-01a from ansee is a co detector that can work standalone or work with alarm host remotely. It adopts lower power consumption microcontroller and high performance electrochemical sensor, with features such as stable, reliable, accuracy, long standby time etc. It can help you protect your home and family from co threats, even when they occur in remote areas of the home or at night when everyone is asleep. The detector will make “di-di-di” sound, and the red led flash fast when alarm occurs, meanwhile the co concentration appears on the lcd. The green led flash 1 times every 30 seconds when it’s under working state. It also has reset and test function. This co detector has low voltage alarm and test function. Press the test button for several seconds, the detector will make alarm sound and the red led will flash fast, meantime the lcd will playback the alarm record circularly with maximum 10 records.
Ch2o(formaldehyde) is a kind of gas which will cause damage to human body. It exists in many products like chemicals, laminate flooring, particle board, household products, glues, permanent press fabrics, paper product coatings, fiberboard, and plywood. It is also widely used as an industrial fungicide, germicide and disinfectant. Jw-100 ch2o detector adopt with high performance electrochemical sensors and sophistic- Ated circuit design, it has features like high stability, excellent anti interference ability. When the indoor ch2o concentration is over the standard, this detector can provide site alarm and remote alarm according to different degrees of ch2o (connect with alarm host).
High-risk security situations do not leave any margin for error thus requiring intricate security procedures designed to ensure safety and piece of mind. The tm-915 has been created specifically with this in mind. Tm-915 mainly used in detecting the close state of door and window, when the door or window opened as unknown reason and the detector will send out specific radio wave to alarm host to achieve remote alarm.
GVD301 vehicle loop detector Type: single channel Supply Voltage: 220V AC±10% Sensing range:20-1500µH Sensitivity: 0.02%-0.2% (7 degrees adjustable) Response time: 50ms Frequency: 2 degree adjustable, 15-120khz Output: 2 output relays (5A/AC230V) Relay 1: presence relay; relay 2: pulse/fault relay; CH1: presence relay; CH2: presence relay Working mode: Model: presence & pulse relay output; Model 2: presence & fault relay output Presence mode: Limited presence/permanent presence Pulse mode: pulse entry/ pulse exit; Pulse output time: pulse entry 200ms, pulse exit 200ms Presence output time: 30mins limited presence/permanent presence; Indicator: red: power, green: status indicator; Internal protection: loop isolation transformer, voltage-regulator tube, voltage dependent thermistance; Temperature:-40—80 centigrade
Specification Technology code for testing of building foundation piles JGJ106-2003 Technical specification of dynamic pile tests for highway engineering JTG/TF81-01-2004 Technology specification for inspection of concrete defects by ultrasonic method CECS 21:2000 Technical specification for detecting strength of concrete by ultrasonic-rebound combine method CECS 02:2005 Technical specification for geotechnical investigation method GB 50021-2001 Purpose Testing building foundation piles by crosshole ultrasonic wave method . Inspecting concrete defects by ultrasonic method, such as uncompacted place, cellular hole area Detecting concrete strength by ultrasonic-rebound combined method Detecting concrete crack depth by ultrasonic method Detecting the wall defects of the hole by one transmitter and two receivers Detecting the strength performance of geotechnical investigation, rock, concrete, etc Performance Fast, precise and automatic to judge the sound parameters. Real-time wave display to assure test efficiency Graphically display the test data, the user can view result directly. Can connect with the test hammer directly to detect the concrete strength. The function has been applied for national patent. Can receive signal with strong sensitivity more than 10m without defects in concrete. The host can supply energy to transducer without external power. Standard USB storage with big capacity Interior lithium battery can supply working power more than 6 hours. And more than 12hours combined with external lithium battery. Portable, small and light apparatus(1.75kg) Extending function to test concrete thickness by impact-echo method Professional and powerful analysis software on Windows system can output the data to Excel or word for advanced analysis.
WAFU remote control lock is an anti-theft lock, which is installed indoors and there is no lock outside, it’s locked and unlocked by remote controllers within 10 meters. So there is no keyhole on the door, and the thefts can’t know where is the lock, so it can be the second lock of home, hotel, and office. One product includes a lock body, 4 remote controllers and a piece of installed accessories. Features: 1.Keyhole-free design: the remote control lock is installed indoors, which have good anti-theft effect. 2.Energy-saving design: the power supply of WAFU remote control lock is two AA batteries, which can use for more than 6 months. 3.Super smart system: WAFU remote control lock is used keelog running password which is difficult to crack among thousand of passwords. 4.Humanization design: WAFU remote control lock can connect to the external USB power, which never cut off, and have emergent buttons here. Specification: 1.Model: WF-008 2.Dimension: 96*155*36mm 3.Color: gold/sliver 4.NW: 0.95 kg 5.GW: 1.3kg 6.Operation Range: within 10m 7.Power Supply: 2 common AA batteries/alternating current 8.Input: DC 100-240V, 50/60A 9.Output: AC 5V, 1000mA 10.Operation Temperature: -20-80°C 11.Operation Humidity: 5-60% 12.Remote controllers number: 4 standard, at most can be registered 16. Note: 1.MOQ: 100 pieces. 2.Price: USD 55-70 FOB Shenzhen 3.Sample: It can be supplied, but it need to charge. 4.Supply Capacity: 30000 pcs/month 5.Package: Gift box packing which is 22.2*19.7*5.8cm, and 12pcs per carton, which dimension is 40*38*23.3cm. 6.Delivery: within 3 to 7 days. 7.Payment: Western Union, Paypal, Bank of China; and pay before delivery.
300W High Power VHF UHF NMT CDMA Single Jammer (Waterproof & shockproof design, it is specially customized to accommodate a fully integrated broad band jamming system which provides the ultimate solution for Military and Police convoys or VIP protection. At a Glance 6 modules are controlled separately and also can work simultaneously. Each module with antenna can be used as a single jammer. The pelican case is portable (can be carried like a suitcase). Can be fixed in car and temporary occasion. Frequency band is optional. With excellent heat dispersion. Specification: 6 Bands Walky-talky (VHF): Walky-talky (UHF/300MHz)/135-155MHz Walky-talky (UHF/350MHz)/155-175MHz Walky-talky (UHF/400MHz)/300-350MHz Walky-talky (UHF/450MHz)/350-400MHz Cellular NMT/400-440MHz Cellular CDMA 450/440-480MHz Total Output Power:300W Control:Each bands can work independently Housing Waterproof & shockproof design suitable indoor or outdoor use Size:56*46*27 cm Total System Weight:Approx 60 kg (with omni directional antennaS.) Humidity:Up to 80% Operation Temperature:-20 ...+50 Centigrade degree Antenna Type:6pcs External( 2-3dBi ) omnidirectional ( Standard ) Shielding Range 300 to 500m ( signal strength
This jammer is a kind of novel designed cell phone and satellite jammers. It can mainly used in bomb disposal and can block the 4 frequencies at the same time. Masterly designed heat-removal system ensures it to continuously working under tough weather. The material quality of its backpack style gives an artistic appearance and durable feature. The blocking frequencies including all the cell phone and satellite phone frequencies and its frequency range can be up to 4. Application fields: -Bomb disposal and military automobile allocation; -Field operations; -Special troops; -VIP protection; -Bandit suppression. At a glance: Portable, backpack style. Lightweight: the whole device with antenna weighs only 18KG or so which is easy to carry; Block 4 frequencies at the same time; Output power can be up to 60W; High gain omnidirectional antenna (directive antenna for your choice); Power supply: built-in Lithium-battery, external DC or AC are accessible too; Continuous working time of the built-in battery can be up to 2 hours if fully charged; The device adopts the high-power wireless amplification technology which can proceed the standing-wave ratio and temperature self-protection. The Specification for this jammer: Number of Frequency bands: 4 bands List of frequency bands per customer choice(up to 4 can be selected) -CDMA/TDMA+Nextel (851-894 MHz), -iDEN -AMPS (869-894MHz), -GSM850 -GSM (925-960 MHz), -High GSM/DCS (1805-1880 MHz), -PCS/GSM1900 [+PHS] (1930-1990 MHz), -UMTS (3G) (2110-2170 MHz) Computer communication standards 2.4Ghz -WLAN Bluetooth Wi-Fi. Satellite communication systems -Thuraya Iridium Elipso Inmarsat GlobalStar -Aces Odyssey GPS CDMA450 Cellphone System -(430-450/460-470 MHz) Output watt: 50watt Power Consumption: Max: 380W Power supply voltage:~230VAC / ~110VAC Power Adjustment: Multi level potentiometer adjustable by computer. Battery 2-3 hours Range Radius: Up to 120 meters ( signal
AVENUES COSMETIC is the best clinic for hair transplant and hair treatment. Here experts give free consultation to their patients before and after the hair transplant.
Place of Origin: Guangdong, China (Mainland) Brand Name: SSG Model Number: T6L Usage: Personal Color: White can customized Function: Home Anti-theft/ home safety GSM Frequency: 850/900/1800/1900MHZ materiral: ABS plastic Radio frequency: 433 -
D6 JP54 D2 BLCO Ilmenite Rutile Zircon
QuadXs2c is one of the most successful controller presently available in the market. Client includes large corporates like firstsource, Ranbaxy, Myntra and many more. This is one of the most flexible hard ware with 4 completely configurable outputs and 8 General purpose inputs. Further integration with fire is possible very smoothly. It supports weigand / HID based readers Features: 4 door / 8 reader Controller Supports access control of up to 4 doors in all respect including 4 entry readers, 4 exit readers, 4 locks, 4 exit switches etc Multiple RFID Technologies Supports all latest RFID technologies with inbuilt EM reader and option of having Mifare/HID iClass/ HID Pros. Network interface Leveraging on the merits of IP based systems, it can easily be hooked up on the existing TCR/IP network. Thus the data can be transferred instantaneously in real time mode to a centralized server. Field Upgradable Firmware Facility to onsite upgrade the firmware over Ethernet interlace so that any customisation or new version can be easily upgraded without any need of removing the device or physical presence of the engineer near the device Protected Enclosures Both controller & power supply unit are protected with suitable housing so electronic circuit boards are not exposed to cause any accidental damage. Anti Pass Back Door wise antipassback. Entry to the particular door is allowed only when the employee has exited through the same door. Door Interlocking Facility of door interlocking is available. The system allows creating a group of doors such that access to a door .thin the group is allowed only when all the other doors are in closed condition. Excellent Price Performance Ratio With a lower price to performance ratio ROI is automatically enhanced, the factor contributing to higher ROI is not only very competitive pricing but also higher accuracy rate offered by the product Fully configurable GPI and GPO Optically Isolated inputs for 4 Door Sensor, 4 Exit Switch & 8 General purpose digital inputs along with 4 General purpose relay outputs. These are fully configurable. For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001 Branch office: 465 | Pocket E-16 | Rohini | New Delhi – 110085
P20 Proximity reader is indigenously developed high performance reader to read EM REID read only card. It provides a consistent read range of 8-10cm in most of the conditions. The reader is particularly suited to access control applications. The same basic unit can be configured to most common output interface formats, including Weigand, Megstripe and Rs-232 serial ASCII. Features: • High aesthetic and appealing looks • User selectable interface e.g. Wiegand, Clock/Data, Rs232 • East firmware upgrade through PC • Green LED and Buzzer can be control by the related control pins. • Output signal for tampering • Card read indication by LED and Buzzer. For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001 Branch office: 465 | Pocket E-16 | Rohini | New Delhi – 110085
P20 Proximity reader is indigenously developed high performance reader to read Mifare read only card. It provides a consistent read range of 4-5cm in most of the conditions. The reader is particularly suited to access control applications. The same basic unit can be configured to most common output interface formats, including Weigand, Megstripe and Rs-232 serial ASCII. Features: 13.56MHz Mifare reader that meets ISO 14443A standards Suitable four door access control applications. It can be easily mounted on walls and doors Reads both 32 bit Mifare CSN and Sector Advance key management for high security Compact and high esthetics Dual LED indications Weigand interface, compatible with most of the existing access control systems. For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001 Branch office: 465 | Pocket E-16 | Rohini | New Delhi – 110085
Our organization hold expertise in distributing, exporting and supplying superior grade BioRover 3S Device India. Our offered BioRover 3S Device is widely appreciated by our customers, which are situated all round the nation. Known for its best quality, clients can avail this BioRover 3S Device at industry leading prices from us. Go mobile, unique handheld biometric device to explore the uncharted application areas. Features: Biometric Handheld Device Battery operated handheld device with reliable authentication by fingerprint and RFID technologies. Large sized high resolution TFT display with touchpad. Option of personalizing the display screen by adding company logo in specified display area. Multiple RFID Technologies Supports popular RFID technologies with inbuilt EM reader and option of having Mifare, HID iClass and HID Prox readers. Fingerprint template can be stored on Mifare card to facilitate data portability & unlimited users. Application Areas Device mobility is the key here. The inbuilt lithium polymer battery handles over 12 hrs. of heavy usage. This opens up choice of using it for various applications e.g. mining, school buses, classroom, infrastructure sites so on and so forth. Elegant and Robust Design Fairly robust product designed. Keeping in mind mostly outdoor usage, a rubber gasket has been given around the device. Appropriate shape, compact size give good grip to the device aside of elegant looks. Data Communication There are multiple interfaces over which the device can communicate with the host computer viz USB, Wifi and GPRS. One has the ease of choosing the interface for transferring the data. The device also has an option of inbuilt GPS, which facilitates to tag the location of the data as well. IP65 Weatherproof Housing Product enclosure is designed to meet IP65 standard of protection. This gives complete protection from dust particles, rainwater, airborne pollutants. Field Upgradable Software Facility to onsite update device software through USB interface. The product updates can easily be applied without the need of removing device and sending it back to the service center. Rugged Optical Fingerprint Sensor Equipped with most reliable fingerprint matching algorithm to ensure unrivaled accuracy with best verifications results. Auto finger update helps in keeping track of finger changes over the period thus takes care of dry, wet and swollen fingers. For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001 Branch office: 465 | Pocket E-16 | Rohini | New Delhi – 110085
Our organization hold expertise in distributing, exporting and supplying superior grade BioStamp 2C Device in India. Our offered BioStamp 2C Device is widely appreciated by our customers, which are situated all round the nation. Known for its best quality, clients can avail this BioStamp 2C Device at industry leading prices from us. A new generation of biometric reader with perfect blend of quality, aesthetics and spectra trust. Features: Biometric Attendance Device Get distinct advantage of field proven fingerprint authentication technology for recording employee attendance. Operational 2 hrs. of battery backup ensures that attendance is recorded even during mains failure. Multiple RFID Technologies Supports popular RFID technologies with inbuilt EMreader and option of having Mifare, HID iClass and HID Prox readers. Fingerprint template can be stored on Mifare card to facilitate data portability & unlimited users. Inbuilt RJ45 Network Interface Leveraging on the merits of IP based networkable device, this product can easily be hooked on to the existing TCP/IP network. Thus the data can be transferred in real time mode to a centralized server for instant usage. GSM For Data Transfer The device has an option of having inbuilt GSM for data transfer. This is very handy for locations where there are no means of network connectivity. Attendance records can be transferred directly to the server without any intervention. IP65 Weatherproof Housing Product enclosure is designed to meet IP65 standard of protection. This gives complete protection from dust particles, rainwater, airborne pollutants. Field Upgradable Software Facility to onsite update device software through Ethernet interface. The product updates can easily be applied without the need of removing device and sending it back to the service center. Rugged Optical Fingerprint Sensor Equipped with most reliable fingerprint matching algorithm to ensure unrivaled accuracy with best verification results. Auto finger update helps in keeping track of finger changes over the period thus takes care of dry, wet and swollen fingers. Tamper Proof Device offers security and generates alarms in case someone tries to fiddle with it. The alarm can be in soft mode e.g. on computer screen or alert on a predefined email. For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001 Branch office: 465 | Pocket E-16 | Rohini | New Delhi – 110085
Our organization hold expertise in distributing, exporting and supplying superior grade BioStamp 2R Device in India. Our offered BioStamp 2R Device is widely appreciated by our customers, which are situated all round the nation. Known for its best quality, clients can avail this BioStamp 2R Device at industry leading prices from us. A new generation of biometric reader with perfect blend of quality, aesthetics and spectra trust. Features: Biometric Access Reader Get distinct advantage of field proven fingerprint authentication technology for allowing access to any restricted area. Industry standard weigand interface support to connect with any access control panel. Ultra Sleek Design BioStamp series of product boasts of high aesthetics with ultra modern design, sleek form factor helps in even installing the product directly on the door panels. IP65 Weatherproof Housing Product enclosure is designed to meet IP65 standard of protection for both hot and cold climates. This gives complete protection from dust particles, rainwater, airborne pollutants and such other environmental threats. Rugged Optical Fingerprint Sensor Equipped with most reliable fingerprint matching algorithm to ensure unrivaled accuracy with best verification results. Auto finger update helps in keeping track of finger changes over the period thus takes care of dry, wet and swollen fingers. Multiple RFID Technologies Supports popular RFID technologies with inbuilt EM reader and option of having Mifare, HID iClass and HID Prox readers. Fingerprint template can be stored on Mifare card to facilitate data portability & unlimited users. Effortless Template Management With inbuilt TCP/IP interface finger print template can be transferred and managed over Ethernet effortlessly through software. The device comes with registration and template management software. Field Upgradable Software Facility to onsite update the device software through ethernet interface so that any customization or product updates can be easily upgraded without any need of removing the device and sending it back to service center. Tamper Proof Device offers security and generates alarms in case someone tries to fiddle with it. The alarm signal can be captured by the control panel to take necessary action. For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001
Two Door / Four Reader Controller TwinXs 3S is a versatile access control panel and supports 2 doors and 4 access readers. The controller can be configured as standalone / Master or Slave. The controller supports host of other rule based features apart from global anti pass back. High Speed Controller with Large Memory The controller has high speed 32 bit processor and has a large storage of 4GB. It has a capacity to store 200000 card holder database and last 500000 event buffer. The high speed processor facilitates access decisions in milliseconds. Local Programming The controller has LCD display and a 12 key keypad. This interface allows use to even program the controller without attaching it to the host computer. Also it facilitates on field diagnostics. Compact Design The controller size is very compact with respect to the number of interfaces. Also it has field pluggable connectors which helps in ease of wiring and termination. The controller is housed in powder coated MS cabinet along with rugged 5 amp power supply. All the reader ports are current limited there by ensuring that the controller doesn’t go down even when any of the port is sorted or malfunctioning. Data Communication and Protocols The controller supports popular communication interfaces viz 10/100 mbps ethernet, CAN and RS485. Master/Slave configuration can be implemented over any of these interfaces. In addition, it supports multiple protocols such as HTTP, SNMP, SMTP, FTP, SSL & NTP. It also supports MODBUS protocol over ethernet for integration. Fully Programmable I/O’s The controller has 8 optically isolated digital inputs out of which 4 are general purpose fully programmable, 2 dedicated for door sensor inputs, and 2 dedicated for egress switch inputs. Also the controller has 4 general purpose outputs apart from lock control outputs. The general purpose outputs are available as potential free contacts. Configurable Reader Interface The reader interface is configurable. The controller also supports legacy clock/ data interface in addition to more popular weigand interface. The weigand interface is configurable from 24 to 64 bits. Field Upgradable Software Facility to onsite update device software through ethernet interface. The product updates can easily be applied without the need of removing device and sending it back to the service center. For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001 Branch office: 465 | Pocket E-16 | Rohini | New Delhi – 110085
The door interlocking system is used to control the entry of a person to a secure area such as a clean room, research lab, etc. where dust or small particles may be a problem or security is of high concern. In its simplest form, the door interlocking is composed of 2 doors that are electrically interlocked in such a way that the doors cannot be opened simultaneously. Another example of Door Interlocking is Man trap. The 4 Door Interlocking Terminal can handle up to 4 doors ( 8 IN/OUT switches ).Thus logic can be built up around the number maximum number of doors ( 4 ) i.e. the manner in which they need to open or close. The 4 Door Interlocking Terminal can handle up to 4 doors ( 8 IN/OUT switches ).Thus logic can be built up around the number maximum number of doors ( 4 ) i.e. the manner in which they need to open or close. Features: • Door Interlocking with Buzzer and Led indicator: Door Interlocking Terminal (DIT) controls interlocking of doors 4 doors using DOTL signals. For user interface there is one switch at entry and EXIT side of a door. Buzzer and LED indicators are used to provide users with visual feedback as to when a door may be accessed. For user convenience, a green light is typically used to signify that a door is ready for access and a red light to indicate that a door is un-accessible. (Additional capability providing Digital outputs which may be utilized for up to 4 more relays controlled by the DIT) • Operations: Only one door may be unlocked or open at one time. Unlocking or opening one door automatically secures all other doors within the designated area. Lock relay contacts will allow low voltage red and green LEDs to be utilized for user feedback. • Programmable: Door interlocking groups can be programmed for 4 doors. User can program interlocking groups through serial communication. • Supports switch less operation: DIT can be used without switch in which led will indicates that user can open the door or not. Switch less operation is same as with switch except that all locks will remain open initially and will get closed if one of the doors of interlocking group is open. Advantages: • Easy to install and configure • Easy to install and configure • Cost saving For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001 Branch office: 465 | Pocket E-16 | Rohini | New Delhi – 110085
