Marble Grinding Mill is a new type machine to grind Talc Stone into super thin Powder. The final Powder size can be from 5micron to 47micron as per 97% passing rate. Marble grinding mill is mainly applied to non-inflammable, non-explosive and brittle materials with Mohs hardness scale under seven, such as calcite, chalk, limestone, dolomite, carbon black, bentonite, kaolin, talc, mica, magnesite, illite, pyrophyllite , roseite, sea-foam, attapulgite , rectorite, diatomite, barite, gypsum, alunite, graphite, fluorite, rock phosphate, kalium ore, pumice etc. totally more than 100 kinds of materials. Finished powder products are in the 325meshs -3000meshs, and yield can be up to 0.5-12 tons per hour. There are five types of Shanghai CLIRIK HGM series marble grinding mill, they are HGM80, HGM90, HGM100, HGM100A and HGM125. Performance and features of Marble grinding mill, stone grinding mill 1. High efficiency 2. Long lifetime of wearing parts 3. High safety and reliability 4. High fineness of products 5. Environment friendly Working Principle of Marble grinding mill, stone grinding mill The main bearing and each dial are driven by electromotor of main machine through reducer, and numbers of rollers, which are rolling in the ring, are driven by dial through plunger. After crushed by hammer crusher, the big materials become small ones and are sent to storage hopper by elevator and further sent to the middle of first dial evenly by the electromagnetic vibrating feeder and feeding pipe. The materials will be driven to the edge of dial by centrifugal force and fall down into the ring, crushed and grinded by roller, and become powder after production of three rings. The high pressure centrifugal blower will inhale air from outside and blow the crushed materials to classifier. The rotating turbo in the powder concentrator will make the coarse powder return to the mill and reground, while the fineness will mix with the air and go into the cyclone and be discharged in the discharge bin, which is at the bottom of it. The air, which mixed with very little fineness, will be purified by impulse duster and discharged by blower and muffler.
Dolomite is a carbonate mineral composed of calcium magnesium carbonate. Dolostone (dolomite rock) is composed predominantly of the mineral dolomite with a stoichiometric ratio of 50% or greater content of magnesium replacing calcium, often as a result of diagenesis. Limestone that is partially replaced by dolomite is referred to as dolomitic limestone. Raw dolomite first enters jaw crusher to be crushed to smaller size. They are lift to storage room by elevator. Vibrating feeder will feed materials into grinding chamber evenly and gradually. After being grinded, the quartz powder will be blow to cyclone by blower. Then the dolomite powder will be transferred to storage room through pipes, and then will be discharged as final products. >>The Application of dolomite ultrafine powder grinding mill: HGM series dolomite ultrafine powder grinding mill is mainly applied to non-inflammable, non-explosive and brittle materials with Mohs hardness under six. Such as calcite, chalk, gravel, dolomite, kaolin, gypsum, etc, totally more than 100 kinds of materials. Product fineness can be controlled between 325~2500 mesh. >>Working Principle of dolomite ultrafine powder grinding mill: The main bearing and each dial are driven by electromotor of main machine through reducer, and numbers of rollers, which are rolling in the ring, are driven by dial through plunger. After crushed by hammer crusher, the big materials become small ones and are sent to storage hopper by elevator and further sent to the middle of first dial evenly by the electromagnetic vibrating feeder and feeding pipe. The materials will be driven to the edge of dial by centrifugal force and fall down into the ring, crushed and grinded by roller, and become powder after production of three rings. The high pressure centrifugal blower will inhale air from outside and blow the crushed materials to classifier. The rotating turbo in the powder concentrator will make the coarse powder materials return to the mill and reground, while the fineness will mix with the air and go into the cyclone and be discharged in the discharge bin, which is at the bottom of it. The air, which mixed with very little fineness, will be purified by impulse duster and discharged by blower and muffler. Should you have any questions, please do not hesitate to contact me.
Gravel has numbers of source and names. Nature gravel is Large called conglomerate, they are a common geological feature, being formed as a result of the weathering and erosion of rocks. While natural gravel deposits are insufficient for human purposes, gravel is often produced by quarrying and crushing hard-wearing rocks, such as sandstone, limestone, dolomite or basalt. Gravel ultrafine grinding line Our gravel grinding mills include Raymond mill, HGM ultrafine grinding mill (HGM80/ HGM90/ HGM100/ HGM100/HGM125). Raymond mill is the vertical grinding mill, which is popular in many countries and has very long history. HGM ultrafine grinding mill is special for super thin grinding. You can choose suitable gravel grinding mill depends on your gravel size, hardness, capacity and your cost budget. Gravel ultrafine grinding line: Clirik has the best gravel ultrafine grinding line. Under the same finished final size and the same motor power, the capacity of micro powder grinding mill is twice as much as jet mill, mixing grinder and ball mill. And the application of pulse deduster and muffler greatly alleviates dust pollution and noise. If you want to reduce the cost of production you can choose our gravel ultrafine grinding mill. Raw gravel first enters jaw crusher to be crushed to smaller size. They are lift to storage room by elevator. Vibrating feeder will feed materials into grinding chamber evenly and gradually. After being grinded, the quartz powder will be blow to cyclone by blower. Then the gravel powder will be transferred to storage room through pipes, and then will be discharged as final products.
Introduce of Stone mill/micro mill/ micro grinder mill/ micro grinding mill: five models: HGM80, HGM90, HGM100, HGM100A, and HGM125 finished production fineness: 300meshes~3000meshes, 5-47 micron the capacity (ton/hour) ranges from 0.4T/H to 12T/H application: HGM series stone mill/micro mill/ micro grinder mill/ micro grinding mill can process various kinds of stones and rocks, such as: Kaolin, limestone, calcite, marbles, barites, gypsums, pyrophyllites, dolomites, calcium carbonates, pigments, clays, coals, carbon black, activated carbons, feldspar, talc, mica, carbon black, petroleum coke, alumina, chromic oxide, quartz, cements, up to more than 100 materials. Working Principle of Stone mill/micro mill/ micro grinder mill/ micro grinding mill: The crusher will crush the big materials into small ones, and then the elevator will send them to the hopper. The vibrating feeder will send the materials to the middle of first dial evenly. The motor of main equipment drives the main shaft and dial through reducer, and the dial drives numbers of rollers moving in the ring channels via pins. The materials will be driven to the edge of dial by centrifugal force and fall down into the ring, crushed and grinded by roller, and become powder after production of three rings. The high pressure centrifugal blower will inhale air from outside and bring the crushed materials to classifier. The rotating turbo in the powder collector will make the coarse materials return to the mill and regrounded, while the fineness will mix with the air and go into the cyclone and be discharged in the discharge bin, which is at the bottom of it. The air, which mixed with very little fineness, will be purified by impulse duster and discharged by blower and muffler.
calcium carbonate grinding mill Calcium Carbonate Mill also is named calcium carbonate grinding mill. Calcium Carbonate Mill (powder grinding mill) is suitable for grinding calcium carbonate into fine powder. After being grinded by the Calcium Carbonate Grinding Mill, the fine powder size can be 300 mesh to 3000mesh for industry usage. The powder output size of Calcium Carbonate Mill (powder grinding Mill)can be adjusted continuously according to the customers' demand. Application of calcium carbonate grinding mill: HGM Series calcium carbonate grinding mill is the equipment specializing in producing fine and superfine powder of non-inflammable, non-explosive and brittle materials with Moh's hardness under six, such as calcite, chalk, limestone, dolomite, kaolin, bentonite, talc, mica, magnesite, illite, pyrophyllite and vermiculite, sepiolite, attapulgite, rectorite, diatomite, barite, gypsum, alunite, graphite, fluorite, rockphosphate, Kalium ore, pumice, etc., totally more than 100 kinds of materials. Should you have any questions, please do not hesitate to contact me.
Heavy Calcium Carbonate powder is almost always used for a raw material of goods, such as plastic, rubber, paint, paper building material, food additive, medicine and the other products. Especially Heavy Calcium Carbonate powder of high purity is used for Crystal glass, Optical glass like lens of camera, and Ceramics for electronic parts. Using CLIRIK heavy calcium carbonate grinding mill to processing the heavy calcium powder, you can get more benefit. Detailed Product Description about Heavy calcium carbonate grinding mill CLIRIK heavy calcium carbonate grinding mill can be use to grind all kinds of non-inflammable, non-explosive and brittle materials with Mohs hardness scale under nine.CLIRIK heavy calcium carbonate grinding mill can grind more than 100 kinds of materials, such as calcite, chalk, limestone, dolomite, kaolin, gypsum, talc and so on. Product fineness can be controlled between 300~3000 mesh (47~5 micron) Production Line Configuration of Heavy calcium carbonate grinding mill The whole set HGM Heavy calcium carbonate grinding mill consists of hammer crusher, bucket elevator, storage hopper, vibrating feeder, main unit, inverter classifier, cyclone collector, pulse deduster system, high pressure positive blower, air compressors and electrical control systems Working Principle of Heavy calcium carbonate grinding mill The main bearing and each dial are driven by electromotor of main machine through reducer, and numbers of rollers, which are rolling in the ring, are driven by dial through plunger. After crushed by hammer crusher, the big materials become small ones and are sent to storage hopper by elevator and further sent to the middle of first dial evenly by the electromagnetic vibrating feeder and feeding pipe. The materials will be driven to the edge of dial by centrifugal force and fall down into the ring, crushed and grinded by roller, and become powder after production of three rings. The high pressure centrifugal blower will inhale air from outside and blow the crushed materials to classifier. The rotating turbo in the powder concentrator will make the coarse powder return to the mill and reground, while the fineness will mix with the air and go into the cyclone and be discharged in the discharge bin, which is at the bottom of it. The air, which mixed with very little fineness, will be purified by impulse duster and discharged by blower and muffler.
Limestone is a sedimentary rock composed largely of the minerals calcite and aragonite, which are different crystal forms of calcium carbonate. A few of limestone are composed from skeletal fragments of marine organisms such as coral or foraminifera. Limestone is usually processed in fine or super fine powder by limestone grinding mill. Limestone grinding mill is a main kind of stone grinding mill. Limestone grinded by CLIRIK limestone grinding mill has numerous uses: as a building material, as aggregate for the base of roads, as white pigment or filler in products such as toothpaste or paints, and as a chemical feedstock. The Application of limestone grinding mill: HGM10036 limestone grinding mill is mainly applied to non-inflammable, non-explosive and brittle materials with Mohs hardness under six. Such as calcite, chalk, limestone, dolomite, kaolin, gypsum, etc, totally more than 100 kinds of materials. Product fineness can be controlled between 325~2500 mesh. Working Principle of limestone grinding mill: The main bearing and each dial are driven by electromotor of main machine through reducer, and numbers of rollers, which are rolling in the ring, are driven by dial through plunger. After crushed by hammer crusher, the big materials become small ones and are sent to storage hopper by elevator and further sent to the middle of first dial evenly by the electromagnetic vibrating feeder and feeding pipe. The materials will be driven to the edge of dial by centrifugal force and fall down into the ring, crushed and grinded by roller, and become powder after production of three rings. The high pressure centrifugal blower will inhale air from outside and blow the crushed materials to classifier. The rotating turbo in the powder concentrator will make the coarse powder materials return to the mill and reground, while the fineness will mix with the air and go into the cyclone and be discharged in the discharge bin, which is at the bottom of it. The air, which mixed with very little fineness, will be purified by impulse duster and discharged by blower and muffler.
Gangue also named as lode mineral, gangue minerals are generally non-metallic minerals, such as calcite, Quartz, kaolin, talc, water mica, chlorite, epidote stone, etc. Types of gangue minerals, content and the symbiotic relationship between the level of ore processing method selection and processing costs tend to have an important impact. With the human growing requirements of the new mineral raw materials and mining, flotation, smelting technologies improve, some no use value gangue minerals future may become the ore minerals. HGM series gangue grinding mill is mainly applied to non-inflammable, non-explosive and brittle materials with Mohs hardness scale under seven, such as calcite, chalk, limestone, dolomite, carbon black, bentonite, kaolin, talc, mica, magnesite, illite, pyrophyllite , roseite, sea-foam, attapulgite , rectorite, diatomite, barite, gypsum, alunite, graphite, fluorite rock phosphate, kalium ore, pumice etc. totally more than 100 kinds of materials. Working principle of HGM series gangue grinding mill: After crushed by hammer crusher, the large materials become small ones and are sent to storage hopper by elevator, edge of then evenly sent to the upper distribution plate of the turnplate by vibrating feeder and sloping feeding pipe. When the grinding mill is at work, all the grinding rollers are rolling in the ring, and the materials are driven to the edge of the turnplate by the centrifugal force and fall down into the grinding chambers where the materials are repeatedly pressed, crushed and grinded by the rollers. The high-pressure air blower constantly inhales air within the grinding mill and, in turn, the air flow with crushed materials are brought to the classifier whose high-speed impeller will screen the airflow: the unqualified particle size will fall and return to the mill for being reground while the qualified particle size mixed with air will go into the cyclone powder collector. Most of the qualified powders will fall an exit from the discharging valve at the bottom; a small proportion of the fine powders, with airflow, moves to the dust cleaner, and clings to the surface of the filter bags. At the same time, the fine powders clinging to the surface fall down by the sudden vibration of the filter bags, which is caused by the instantly ejected high-pressure gas controlled by the pulse valve. The materials from the above two lots are sent by the conveyor at the bottom to get finished powders packed. In addition, filtered clean air will be emitted from the air outlet of muffler in the end.
Introduce Of High pressure suspension grinding mill Clirik High pressure suspension grinding mill is suitable for processing various non-flammable and non-explosive mineral materials with Mohs hardness less than 9.3 and humidity less than 6%, it is widely used in the fields of metallurgy, construction, chemical industry, mining, highway construction etc,. The granularity of the finished powder size can be adjusted between 50 and 325 mesh (315-45 micron). Examples of processing materials include quartz, feldspar, barite, calcite carbonate, limestone, talc, ceramic, iron ore, carborundum, bauxite, rock phosphate, coal and other materials, total about 400 kinds of materials. Big materials are crushed by jaw crusher to the required particle sizes, and carried by bucket elevator to the storage hopper, and are fed evenly and continuously by vibrating feeder into the main unit for grinding. The grinded powder are carried by the airflow from the blower to the classifier to be classified, the particles which meet the fineness enter cyclone collector through pipe, and are separated and collected there. They are discharged at the discharging valve to become finished products; the airflow is sucked to the blower by return pipe on the top of cyclone collector. The whole airflow system is a sealed circulation, and is circulated under positive and negative air pressure.
HGM90 stone grinding mill is the new type mining equipment for making micro powders, fine powdersï¼?which is widely applied in the industries of metallurgy, mining, chemistry, cement, construction, refractory materials, ceramics, and so on. Production Line Configuration of HGM90 stone grinding mill: The whole set HGM90 stone grinding mill consists of hammer crusher, bucket elevator, storage hopper, vibrating feeder, main unit, inverter classifier, cyclone collector, pulse deduster system, high pressure positive blower, air compressors and electrical control systems. Application of HGM90 stone grinding mill: HGM90 stone grinding mill(calcite carbonate grinding mill, chalk grinding mill, limestone grinding mill, dolomite grinding mill, kaolin grinding mill, bentonite grinding mill , talc grinding mill, mica grinding mill, magnesite grinding mill, pyrophyllite grinding mill, ceyssatite grinding mill, barite grinding mill, gypsum grinding mill, alunite grinding mill, granite grinding mill, fluorite grinding mill, phosphate rock grinding mill, kalium ore grinding mill , float stone grinding mill)is mainly applied to non-inflammable, non-explosive and brittle materials with Mohs hardness under six. Such as calcite, chalk, limestone, dolomite, kaolin, gypsum, etc, totally more than 100 kinds of materials. Product fineness can be controlled between325~3000 mesh. Working Principle of HGM90 stone grinding millï¼? The main bearing and each dial are driven by electromotor of main machine through reducer, and numbers of rollers, which are rolling in the ring, are driven by dial through plunger. After crushed by hammer crusher, the big materials become small ones and are sent to storage hopper by elevator and further sent to the middle of first dial evenly by the electromagnetic vibrating feeder and feeding pipe. The materials will be driven to the edge of dial by centrifugal force and fall down into the ring, crushed and grinded by roller, and become powder after production of three rings. The high pressure centrifugal blower will inhale air from outside and blow the crushed materials to classifier. The rotating turbo in the powder concentrator will make the coarse material return to the mill and reground, while the fineness will mix with the air and go into the cyclone and be discharged in the discharge bin, which is at the bottom of it. The air, which mixed with very little fineness, will be purified by impulse duster and discharged by blower and muffler.
Cement vertical mill plant introduction China supplier about Cement vertical mill, Cement vertical roller mill: We are a leading manufacturer of Cement vertical mill, Cement vertical roller mill in Shanghai, China. As a professional manufacturer of this kind of machine, we have been in this line for many years, and now our products spread over the world for the good quality and competitive price. Types of Cement vertical mill, Cement vertical roller mill: 1. Finished powder products are in the 325meshs -3000meshs, and yield can be up to 0.5-12 tons per hour. There are five types of Shanghai CLIRIK HGM series Cement vertical mill, Cement vertical roller mill; they are HGM80, HGM90, HGM100, HGM100A and HGM125. 2. Finished powder products are in the 20meshes-325meshes, and yield can be up to 1-20 tons per hour. There are also fine models of this type cement vertical mill in CLIRIK, they are YGM7815, YGM8314, YGM9517, YGM4121 and MTM1600. Detailed Product Description about Cement vertical mill, Cement vertical roller mill: Cement vertical mill, Cement vertical roller mill is mainly applied to grind non-inflammable, non-explosive and brittle materials with Mohs hardness under nine. Such as calcite, chalk, limestone, dolomite, kaolin, gypsum, and talc etc, totally more than 100 kinds of materials. Product fineness can be controlled between 20~3000 mesh Comparable with ball mill, Cement vertical mill, Cement vertical roller mill has features of low cost, high capacity, easy operation. Working Principle of Cement vertical mill, Cement vertical roller mill: The main bearing and each dial are driven by electromotor of main machine through reducer, and numbers of rollers, which are rolling in the ring, are driven by dial through plunger. After crushed by hammer crusher, the big materials become small ones and are sent to storage hopper by elevator and further sent to the middle of first dial evenly by the electromagnetic vibrating feeder and feeding pipe. The materials will be driven to the edge of dial by centrifugal force and fall down into the ring, crushed and grinded by roller, and become powder after production of three rings. The high pressure centrifugal blower will inhale air from outside and blow the crushed materials to classifier. The rotating turbo in the powder concentrator will make the coarse powder return to the mill and reground, while the fineness will mix with the air and go into the cyclone and be discharged in the discharge bin, which is at the bottom of it. The air, which mixed with very little fineness, will be purified by impulse duster and discharged by blower and muffler.
CemMate 400 High limestone content type cement grinding aids Description CemMate 400 is a kind of high limestone content type cement grinding aid. By the use of CemMate 400, without the new investment and change of existing cement grinding process equipment, it can be realized that: - Mill output is increased; - Cement quality is improved; - Part of clinker is saved; - Energy cost is reduced. Scope of the application Applicable for grinding of portland limestone cement with high limestone content. Property CemMate 400 is non-toxic, non corrosive, non flammable, non explosive. Technical characteristic - Increasing mill output. This product can effectively remove the electrostatic agglomeration due to grinding, reduce the agglomeration between cement particles, and the agglomeration between particles and pound mills. The mill output can be increased by 8ï½?15%. - Improving cement quality. The strength of cement at different ages can be increased significantly. The 3 days compressive strength can be enhanced by 2ï½?5 MPa and the 28 days compressive strength can be enhanced by 3ï½?8 MPa. - Saving part of clinker. This product helps to mix more limestone into the cement than without using this product, so that limestone content can reach over 25%. - Reducing energy consumption. The electricity used in the production of per ton of cement can be saved by 3ï½?5 kw/h. - Others. There is no corrosive effect on grinding equipment and concrete reinforcement. It has no adverse effect on the work performance, mechanical properties, deformation performance and durability of concrete. Dosage The dosage of CemMate 400 is related to the physical properties of cement products. The recommended dosage is 300ï½?1000 grams / tons of cement (0.03ï½?0.1% of cement weight). The optimum dosage must be determined by testing on the cement mill. Usage method In order to achieve the most stable using effect, CemMate 400 shall be accurately added by an adjustable liquid metering pump that matches the type and output of the cement mill. The liquid metering pump must be calibrated before use. CemMate 400 can be added to the clinker belt conveyor or the front of the mill. Technical service Professional engineers can combine the details of the cement plant to make experiment and recommend the mill parameters to the cement plant. CemMate 400 is one kind of cement grinding aid. According to the condition and demand of cement plant, professional engineers can design the most suitable cement grinding aid for many kinds of cement from cement plants to adjust cement performance, such as: setting time, water requirement of normal consistency, fluidity, adaptability of cement concrete, etc. Package 200 L/drum, intermediate bulk container. We provide free sample for mini mill test and technical support throughout the whole application process. We look forward to the cooperation with the agent worldwide.
Shanghai Clirik Machinery Co., Ltd is a large professional manufacturer of Gypsum Powder raymond mill,The Clirik Gypsum Powder raymond mill have five models: YGM7815,YGM8314,YGM9517,YGM4121,MTM1600. Shell Size:15-35mm Grinding Weight:1.2 - 11 T Application:The Gypsum Powder raymond mill is widely used in small and medium mining, chemicals, building materials, metallurgy, refractories, pharmaceuticals, cement and other industries. Raw Material:such as gypsum, talc, calcite, limeOre, marble, barite, dolomite, granite, kaolin, bauxite, fly ash , oxidation iron oxide red, iron ore, etc. Output:30 - 425 mesh Introduction of Gypsum raymond mill: Gypsum Powder raymond mill, also known as Raymond Grinder or Pendulum Grinder, is designed by CLIRIK Machinery with Germany technology. The Gypsum Powder raymond mill is more efficient than ball mill in some area, with features of closed circuit for high fine powder devices. Gypsum Powder raymond mill Features : 1.Low production cost, high-performance Overall for the vertical structure, small footprint, systematic, from raw material delivered to the milling and roughing to final packaging, of an independent production system 2.Good stability, high reliability Raymond Host transmission device adopts enclosed gear boxes and pulleys, transmission smooth, reliable operation. 3.Perfect particle size Electrical system adopts centralized control, milling workshop basic enabling unmanned operation. Structure of Gypsum Powder raymond mill Gypsum Powder raymond mill(Rammond roller mill) is mainly composed of main unit, analyzer, fan, dischargeing cyclone separator, powder cyclone separator and air duct. Among them, the main unit consists of frame, blow shell, shovel, grinding roller and grinding ring. Working principle of Gypsum raymond mill The rollers tightly rolled on the ring under the effect of centrifugal force. Shovel sends material between the roller and ring and the material is grinded into powder under the high pressure.Then the fan blows the power up into the analyzer. At this time, the power material met the fineness requirement get through the analyzer and get into the power cyclone separator while the others will be sent back for re-grinding.The whole system is airtight circulation. http://www.raymond-mill.com/products/Specific_Raymond_mill/69.html
Product descriptions about YGM8314 Raymond Roller Mill: Clirik YGM8314 Raymond grinding mill, Raymond mill is suitable for processing various non-flammable and non-explosive mineral materials with Mohs hardness less than 9.3 and humidity less than 6%, it is widely used in the fields of metallurgy, construction, chemical industry, mining, highway construction etc,. The granularity of the finished powder size can be adjusted between 50 and 325 mesh (315-45 micron). Examples of processing materials include quartz, feldspar, barite, calcite carbonate, limestone, talc, ceramic, iron ore, carborundum, bauxite, rock phosphate, coal and other materials, total about 400 kinds of materials. Features of YGM8314 Raymond Roller Mill: YGM8314 Raymond grinding mill, Raymond mill has the similar working principle as High pressure suspension grinding equipment, but its grinding device is fixed with 1000-1500kg pressure springs. When the machine works the grinding roller, which under the action of high pressure spring and centrifugal force, rolls close up to grinding ring, its rolling pressure is 1.2 times higher than that of High pressure suspension grinding equipment given an identical condition and its capacity increase 20% to 30%; When the grinding roller and grinding ring, stable capacity and fineness are guaranteed. Operating Principle of YGM8314 Raymond Roller Mill: Big materials are crushed by jaw crusher to the required particle sizes, and carried by bucket elevator to the storage hopper, and are fed evenly and continuously by vibrating feeder into the main unit for grinding. The grinded powder are carried by the airflow from the blower to the classifier to be classified, the particles which meet the fineness enter cyclone collector through pipe, and are separated and collected there. They are discharged at the discharging valve to become finished products; the airflow is sucked to the blower by return pipe on the top of cyclone collector. The whole airflow system is a sealed circulation, and is circulated under positive and negative air pressure. Features of YGM8314 Raymond Roller Mill YGM8314 Raymond grinding mill, Raymond mill has the similar working principle as High pressure suspension grinding equipment, but its grinding device is fixed with 1000-1500kg pressure springs. When the machine works the grinding roller, which under the action of high pressure spring and centrifugal force, rolls close up to grinding ring, its rolling pressure is 1.2 times higher than that of High pressure suspension grinding equipment given an identical condition and its capacity increase 20% to 30%; When the grinding roller and grinding ring, stable capacity and fineness are guaranteed.
Featuresï¼? 1. It is used for grinding raw materials of large and medium livestock and aqua feed mills. It can also be used for grass and pharmacy fine grinding. The granular raw materials, such as corn, sorghum, wheat, beans, etc can be ground; 2. It is derived from the tear circle type hammer mill and efficiency can be improved by 45%-90% compared to universal hammer mill; 3. It can produce qualified aqua feed under full load with ï¿ 0.8ã??ï¿ 1 screen and reduce jam significantly. Both coarse and fine grinding can be completed without changing screens; 4. The right aspiration can make materials go through screen quickly, reduce temperature of grinding chamber and increase output effectively.
This ball mill is mainly used for grinding raw materials and final products in cement plant. It can be replaced by vertical raw mill. It is also suitable for grinding various ores and other materials in the metallurgy, mine, chemical, construction and other industries. Besides, the raw mill has two forms of milling, one is an open form, and the other is a recycle close form equipped with powder concentrator. It is widely applied to many industries and has convenient operation.
The ball mill for clinker is an efficient tool for fine powder grinding. It is mainly used to grind the clinker and raw materials in cement industry and also can be applied in metallurgy, chemical, electric power and other industries to grind all kinds of ores. Cement ball mill is not only suitable for over-flow grinding, but also applicable for cyclic close-flow grinding together with powder collector. There are two ways of grinding: the dry way and the wet way.
Our GGBS ball mill is a key grinding machine mainly used to process materials by crushing process, and it is widely used in various manufacture industries, like cement, silicate, new building material, refractory material, fertilizer, ferrous metal, nonferrous metal and glass ceramics. In addition, the slag mill can also be used in dry and wet grinding for all kinds of ores and other materials.
Coal ball mill is the equipment used for grinding and drying coal with different hardness. It is mainly composed of feeding device, principal axis, rotating part, transmission part, discharging part, high-pressure starting device and lubrication system. The coal grinder is also widely used to break various hardness of coal in cement industry, metallurgy industry and chemical industry and so on.
Rotary lime kiln is the main equipment of lime production line. It is widely used for many industries like metallurgy, chemical industry, building refractory materials, environmental protection, etc. The rotary kiln consists of cylindrical shell, supporting roller, supporting device of thrust roller, driving unit, moveable kiln head, sealing device on the tail of kiln, coal dust pipe device, etc., the kiln body has a certain tilt angle with level. The whole kiln body is supported by the roller supporting device, and it is also equipped with thrust roller device to control the up and down movement of the kiln body.
