Asuring via digital Gearcase. Such microprocessor control is designed to optimize the Charging cycles for any type of battery. • 230v coil three-pole contactor. • d.C. Fuse on rectifier output. • delta-star stray flux three-phase power transformer class h; Impregnated in autoclave with ecological epoxy resins, with Thermocouples for disconnection due to maximum temperature. • three-phase rectifier bridge with silicon diodes, natural cooling, with
Over voltages, polarity reversal, anomalies. Error code of any anomaly, inner self ventilation Through forced air, efficiency > 85%, mass-produced Mains leads, input cable, connection to the battery Through anderson-rema power terminals. Nfm Switching battery charger, high frequency technology, Fully controlled by microprocessor. 240v single-phase +- 10%, luminous display for a Easy reading of the charging parameters. Different charging curves in accordance with the kind Of battery and choose among 16 standard curves, Preprogrammed valid for pb-acid, gel. Battery voltage and charge current can be changed Through the button in the front panel. “soft start” mode and display of the charging cycle With led . Electronic protection and/or fuse against short circuits Over voltages, polarity reversal, anomalies. Error code of any anomaly, inner self ventilation Through forced air, efficiency > 85%, mass-produced Mains leads, input cable, connection to the battery Through anderson-rema power terminals. Nfc Switching battery charger, high frequency technology, Fully controlled by microprocessor. 240v single-phase +- 10%, luminous display for a Easy reading of the charging parameters. Different charging curves in accordance with the kind Of battery and choose among 16 standard curves, Preprogrammed valid for pb-acid, gel. Battery voltage and charge current can be changed Through the button in the front panel. “soft start” mode and display of the charging cycle With led . Electronic protection and/or fuse against short circuits Over voltages, polarity reversal, anomalies. Error code of any anomaly, inner self ventilation Through forced air, efficiency > 85%, error code Display missing, mass-produced input network cable, Output cables polarized.
Ptek nre3 three phase is designed to recharge medium - large capacity traction And start lead-acid batteries, developed using our forty-year experience in the field Of battery chargers and multi-years application of microprocessor control systems D electronic circuit conforming to the Directive on electromagnetic compatibility and ce marking, automatic disconnection Of battery charger due to battery disconnection, equalization charge based on Time, charging with decreasing current (wa characteristic):9÷11 h charging time, Transformer thermal protection, modular installation on galvanized steel base, sheet Steel case with modular panels, epoxy powder coating, oven-baked, standard color: Ral 5003 blue, option: custom-made color, logo and silk-screen printing, mains Input and d.C. Output polarized cables, complete with mains and battery cables; Assembly of plugs and battery connectors on request. “wa” characteristic (din 41774): Charge at decreasing current with intervention of adjustable final Charge from 2.35 to 2.40 v/cell., final charge with timed control 9h / 11h, fixed charging time (equalization charge excluded), equalization Charge (week-end charge). It will start after 55’ from charge end, Duration of equalized charging phase: each hour 5’ (repeated for 48 Hours), calculation to determine the size of suitable battery charge: 16a for every 100 ah of the battery (e.G. 500 ah battery: 16ax5 = 80a).
Ptek nr3 three phase is designed to recharge medium - large capacity traction and Start lead-acid batteries, developed using our forty-year experience in the field of Battery chargers and multi-years application of microprocessor control systems which On, short check of functions and Times, option to program the equalized charge automatically, lab tested electronic Circuit conforming to the directive on electromagnetic compatibility and ce marking, Automatic disconnection of battery charger due to battery disconnection, equalization Charge based on time, charging with decreasing current (wa characteristic): 9÷11 H charging time, transformer thermal protection, modular installation on galvanized Steel base, sheet steel case with modular panels, epoxy powder coating, oven-baked, Standard colour: ral 2004 orange, option: custom-made color, logo and silk-screen Printing, mains input and d.C. Output polarized cables, complete with mains and Battery cables; assembly of plugs and battery connectors on request. “wa” characteristic (din 41774): Charge at decreasing current with intervention of adjustable final Charge from 2.35 to 2.40 v/cell., final charge with timed control 9h / 11h, fixed charging time (equalization charge excluded), equalization Charge (week-end charge) to be recalled. It will start after 55’ from Charge end, duration of equalized charging phase: each hour 5’ (repeated for 48 hours), calculation to determine the size of suitable Battery charge: 16a for every 100 ah of the battery (e.G. 500 ah Battery: 16ax5 = 80a).
Noiseless and ecological electric vehicole/tractor. 16 Km/h. Direct use: you get on, drive and stop (movement dynamics). For all employees who move in a range greater than 100 mt. For quick repair service and transport of small-sized components. Average time saving of about 40 to 60 minutes per day. TECHNICAL FEATURES: - Turning radius: cm. 120 - Length. 140 - Width cm. 85 - Height. 110-130 - Minimum height from ground cm. 5.4 - Weight: Kg 120/140 depending on the type of batteries installed. - fiberglass shell fully recyclable - tube frame with thick serial number for traceability - Handlebar adjustable in height - cover tires 3.00-4 with room air (can puncture tires) - Headlight and taillight - Safety button "ride-on" - Reverse insertable lever - horn, rear view mirror and the battery charge indicator - Electric motor 24 volt permanent magnet 780 watt - Electronic high-frequency MOSFET technology controlled by a microprocessor to recover energy during braking - N. Two 12-volt batteries - lightweight tubular plate traction - 105/125 Ah. - Built-in charger and automatic battery status. - Drive chain high strength pinion - Differential aluminum satellites treated steel - Shaft couplings with 6 quarries - Voltage reducer 24 to 12 volt lighting system - Brake system: front disc brake, rear differential, brake lever on the left and engine braking enhanced by the setting of the electronic control. - Colors: white, red, green , yellow, blue, black, orange (other colors on request).
Noiseless and ecological electric tractor. 10 Km/h. -offers two different advantages: it allows to move very quickly and transport up to 300 kg of materials by using a truck designed by us. Speedy, handy in narrow spaces, it spins around with the truck within a 200 cm radius allowing quick access to other departments. Quick repair and maintenance of big- sized and heavy materials (the truck is 120x80 cm with a carrying capacity of 300 kg). Allows to avoid using big and expensive vehicles to move small volumes of goods. TECHNICAL FEATURES: - Turning radius: cm. 120 - Length. 140 - Width cm. 85 - Height. 110-130 - Minimum height from ground cm. 5.4 - Weight: Kg 123/143 depending on the type of batteries installed. - fiberglass shell fully recyclable - tube frame with thick serial number for traceability - Handlebar adjustable in height - cover tires 3.00-4 with room air (can puncture tires) - Headlight and taillight - Safety button "ride-on" - Reverse insertable lever - horn, rear view mirror and charge indicator battery 24 volt 800 watt electric motor RR 1/10 - 24 volt electric motor permanent magnet 780 watt - Electronic high-frequency MOSFET technology controlled by a microprocessor to recover energy during braking - N. 2 Batteries 12 volt - tensile tubular plate - 102/157 Ah. - Built-in charger or external high frequency and automatic control of the state of charge. - Traction Chain gear ratio 1/10, 125 - Differential aluminum satellites treated steel - axle shafts with couplings 6 slot - Voltage reducer 24 to 12 volt lighting system - Brake system: front disc brake, rear differential, brake lever on the left and engine braking enhanced by the setting of the electronic control. - Colours: white, red, green, yellow, blue, black, orange (other colors on request).
Noiseless and ecological electric tractor. Moderate purchase price In these facilities, Bigà can be used for: - individual transport of personnel - control, inspection and security service - maintenance, cleaning and transport of small packages - towing with trucks up to 800 kg GENERAL FEATURES: - Turning radius: cm. 120 - Length. 140 - Width cm. 85 - Height. 110-130 - Minimum height cm. 5.4 - Weight: Kg 120/140 depending on the type of batteries installed - fiberglass shell fully recyclable - tube frame with thick serial number for traceability - Handlebar adjustable in height - cover with 3.00-4 tires room air (can puncture tires) - Headlight and taillight - Safety button "ride-on" - Reverse insertable lever - horn, rear view mirror and the battery charge indicator - Electric motor 24 volt permanent magnet 800 watt - 24 volt 800 watt motor RR 1/10 - Electronic high-frequency MOSFET technology controlled by a microprocessor to recover energy during braking - N. Two 12-volt batteries - Traction tubular plate - 102/157 Ah - Built-in charger or external high frequency and automatic control of the state of charge. - Drive chain high strength pinion - Differential aluminum satellites treated steel - Shaft with grafts and 6 hp - Voltage reducer 24 to 12 volts for lighting system - Brake system: front disc brake, rear differential, brake lever on the left and enhanced engine braking from the calibration of the electronic control. - Blue color.
Electric cart SPECIFICATIONS: Dimensions: Total Length mm 930 Width mm. 650 Height mm. 1070 Floor Length mm 870 Width mm. Ground Clearance 620 mm. 330 Weights: Total kg including batteries. 77.90 Batteries kg. 13 each. x 2 Motor: Permanent magnet motor with electric 200 W - rpm 120 - 24 V electro 24VDC 2Nm. Voltage and batteries: no Two 12V batteries 32 A C5 sealed gel - series connection, without maintenance. External charger 24 v - 8 ampere - Electronic microprocessor - Power supply 220 v. Brakes: Electric brake block engine, listing in the event of power failure. braking on deceleration (engine braking) enhanced in the calibration of the parameters of the controller. Speed and Capacity (performance with the vehicle in perfect working order on flat surface: Max 5 Km / h + / - 10% Max 250 kg. terms and 100kg. slope of 15%. Maximum flow rate is considered with the load distributed uniformly on the floor. Tires: 2 wheels rubber tires mounted on rims with pneumatic 3.00-4 6-ply roofing. 2 wheels 200x50 diameter core polypropylene gray synthetic rubber ring mounted on swivel mounts. Frame: Tubular steel and Fe 37 powder-coated polyester for outdoor Ral 6018 Spare parts and tools for the maintenance and repair: Original spare parts and tools for maintenance and repair are provided directly to order from Italy Bigà spa. Sound level values: less than 70 dB (A)
5 - Foot sheet chariot 5.1 Dimensions: Total length 930 mm Width 650 mm Height 1070 mm Plan Length Width mm 870 mm 620 mm Ground clearance 330 5.2 Weights: Total 77.90 kg including batteries Batteries 13 kg each. x 2 5.3 Motor: Permanent magnet motor with electric 200 W - rpm from 120 to 24 V electro 2Nm 24VDC. 5.4Voltaggio and batteries: N. 2 x 32 A 12 V sealed gel in C5 - series connection, maintenance-free. External charger 24 V - 8 amp - Electronic microprocessor - Power supply 220 V 5.5 Brakes: Electric brake to the engine block, insertion of a power failure. Braking on deceleration (engine braking) enhanced in the setting of parameters control unit. 5.6 Speed and Capacity (performance of the vehicle in perfect working flat route: Maximum speed in 6 seconds of continuous accelerated 5 km / h + / - 10% Max capacity 250 kg and 100kg in terms of gradient of 15%. The maximum flow is considered with uniformly distributed load on the floor. 5.7 Tyres: 2 rubber wheels mounted on wheels with pneumatic 3.00-4 6-ply roofing. 2 wheels 200x50 core diameter polypropylene ring mounted on gray synthetic rubber supports swivel. 5.8 Structure: Tubular and sheet S 235 JR polyester powder coated RAL 6018 external 5.9 Spare parts and tools for maintenance and repair: The original spare parts and tools for maintenance and repair are provided directly Order by Biga spa Italy. 5.10 Values sound level: less than 70 dB (A) 5.11 Environmental conditions: temperature + 5 + 40 C Humidity 50%.
Technical sheet Biga’ pick-up: Dimensions: Total Length mm 1541 Width mm. 740 Height mm. 1120 Worktop length mm 95 Width mm. 740 Height from the ground mm. 310 Weight: Total including batteries and banks kg.156 Set 3 banks kg. 4 Batteries kg. 27,5 each x 2 Gear Motor: Permanent magnet engine R.R. 10/1 800 W – rpm 330 – 24 V. Voltage and battery: N. 2 batteries capacity 12V 140 A C20 hermetic gel– connected in series, no maintenance. External battery charger 24 v – 12 amp – electronic microprocessor control- Power 220 v. Differential and transmission: Differential, maximum torque of torsion 2 Kgm - 2 Semiaxis with graft at 6 caves Type 13: transmission chain, Sprocket 13 teeth, Crown wheel 45 teeth, Ratio 1/3,47 Type 19. transmission chain, Sprocket 19 teeth, Crown wheel a 45 teeth, Ratio 1/2,37 Type 23: transmission chain, Sprocket 23 teeth, Crown wheel 45 teeth, Ratio 1/2,00 Type 28: transmission chain, Sprocket 28 teeth, Crown wheel 45 teeth, Ratio 1/1,61 Type 34: transmission chain, Sprocket 34 teeth, Crown wheel 45 teeth, Ratio 1/1,33 Brakes: Front drum brake, activation with right hand Back drum brake, activation with left hand Service brake, activation on left lever. Braking increase by the release of the accelerator (engine brake) enhanced in the setting of the parameters of the junction box. Speed and capacity: Towing besides the driver (performance with the vehicle in perfect efficiency) on flat road. The maximum capacity is considered with uniformly distributed load on the worktop and the center of gravity of the goods must not exceed the height of mm. 350 Type 13 max 5 Km/h +/- 10% P/T 800 kg. on the plane P/T 100 Kg. on slopes 15% Type 19 max 6,5 Km/h +/- 10% P/T 600 kg. on the plane Type 23 max 8,5 Km/h +/- 10% P/T 450 kg. on the plane Type 28 max 10,5 Km/h +/- 10% P/T 300 kg. on the plane Type 34 max 12 Km/h +/- 10% P/T 200 kg. on the plane Tires: Covering: 3.00-4 superelastic rubber Structure: Tubular and sheet Fe 37 polyester powder painted for outdoor use Ral 9007 Lights and Devices: signaling and illumination main headlight and tail lights reverse buzzer, horn.
Electric small tower tractor. SPECIFICATIONS: Biga 'Pick-up versions and performance with the vehicle in perfect working on flat surface. type 13 max 5 Km / h + / - 10% P / T 800 kg. on the P / T 100 Kg on slope 15% Type 19 max 6,5 Km / h + / - 10% P / T 600 kg. Type 28 up to 8 Km / h + / - 10% P / T 400 kg. Type 34 up to 11 Km / h + / - 10% P / T 200 kg. The maximum range is considered with the load evenly distributed on the plane and the center of gravity of the goods must not exceed the height of mm. 350. Dimensions: Total Length mm 1540 Width mm. 740 Height mm. 1130 Floor Length mm 940 Width mm. Ground Clearance 740 mm. 310 Weights: Total including batteries and banks kg. 176th September 3 banks kg. Batteries kg. 36 each. x 2 Motor: permanent magnet motor RR 10/1 800 W - rpm from 330 to 24 V. N. 2 batteries 12V 140 A sealed gel - connected in series, without maintenance. External charger 24 v - 12 amp - electronic microprocessor - 220 v. transmission: Differential, max. 2 Kgm torque - 2 Shaft with graft rejection in 6 slot. chain drive with front and rear sprocket. Brakes: Front drum, drive with your right hand. Rear disk drive with his left hand. brake, drive on left lever. increased by releasing the brake (engine brake) enhanced in the calibration of the parameters of the controller. Covers: 3.00-4 rubber tires Frame: Tubular steel and Fe 37 powder-coated polyester for outdoor Ral 9007. lighting and signaling devices : Headlight main and tail lights - reverse buzzer, horn. phonometric values: values ??LpAm max = 77.6 - 85.6 LWA - Attendant Leq dB (A) 77.6 Vibration value: vmax (i) = 0.47 m / s2 (maximum value for operator sitting in the driver's seat). Spare parts and tools for the maintenance and repair: Original spare parts and tools for maintenance and repair are provided directly to order from Italy Bigà spa.
A series EAGLE is composed of two models for electrosurgery which can all be connected to an independent Argon gas module and max. powers of 400 W and 280 W; there is also one model for electrosurgery which built in Argon gas and max. power of 400 W. The units have got 17 currents: 10 for the monopolar usage and 7 for the bipolar usage. Three for the monopolar cut, Three for the monopolar cut, Four for the monopolar coagulation, Two for the bipolar cut, Two for the bipolar coagulation, Two for the bipolar coagulation, One for the coagulation / sealing of big vessels. All the output currents are completely self controlled through a micro-processor with three different systems: - ADC System - APC System - Starting impulse control, which electronically checks the starting pulse of the cut currents. The EAGLE models are equipped with a circuit that can verify the connection/contact of the neutral electrodes ônon Splitö type with a single section and ôSplitö type with a double section with interrupts delivery of the power and luminous acoustic alarm signal. The units can be used with one double pedal footswitch, which allows the activation of the monopolar or bipolar functions, and with a second double pedal foot-switch, which is indicated for the independent activation of the bipolar functions only. The all models allow memorizing and then selecting through a simple button 100 complete functioning programs and are equipped with: two monopolar outputs, which can be used at the same time by two different operators through the Twin activation device; two bipolar outputs. All models are equipped with an auto-check system at double microprocessor: - Main Auto-Check, main auto-diagnosis procedure at the switching-on. - Standard Auto-Check, continuous check of all the functioning parameters during the usage. - Immediate interruption of the functioning with contemporary alarm signal for the operators through specific Error Codes HF Leakage Control, check of the high frequency leakage currents to earth. Auto-Check Argon section. Automatic output of the right modulated and pulsed spray coagulation when the Argon gas coagulation is activated independently from the type of coagulation selected for the simple electro-surgery, and selfcompensation of the gas flow according to the diameter of the electrodes, with a perfect control of the penetration depth. The units can be equipped with automatic activation aspirators that guarantee the efficacious and silent elimination of smokes or electro-surgical aerosol.
The top of the aerosol therapy equipment. Maximum portability with exceptional performance. This electronic device for aerosol therapy can be used anywhere since it can work with unit electrical adapter or with rechargeable batteries (optional). The nebulization is very fast and can be adjusted to three different levels. The nebulized particles are extremely effective with a very low MMAD able to reach the deep airways. The total lack of noise, the presence of a base that can be fixed with velcro to the child's bed, makes the product extremely comfortable and suitable for pediatric use. As a matter of fact, a mother could also perform the therapy while holding the baby in the arms or while the baby is sleeping in bed. The total absence of noise won't intimidate the children and will make the therapy easier. The electronic functions are controlled by a microprocessor. The LCD screen informs you of the working status, facilitating the use of the product. The device has a nebulizing chamber that ensures the thermal stability of the atomized medicine preventing any alteration. Also tested with beclomethasone and budesonide. Maximum speed: 1cc minute - 1 ml minute Particle dimension range: 90%
