Cast aluminum-magnesium alloy Category:Aluminum alloy casting Cast Aluminum-magnesium alloy are widely used in the fields of electronics, automobiles, and aerospace. Common grades are 7A09 etc. The main elements of aluminum-magnesium alloy include aluminum and magnesium. The alloy products have high strength, low density and strong heat dissipation capacity, so they are popular in the fields of electronics, automobiles, and aerospace. Common grades are 5052, 5754, 5083, etc. Aluminum alloys have lower cost, superior performance and stronger product competitiveness. The density of aluminum-magnesium alloy is small, so it is lighter under the same volume, and has a certain strength, which can be used for load-bearing. Aluminum-magnesium alloy has strong heat dissipation, and at the same time, it can resist electromagnetic interference and has strong electromagnetic shielding. Its appearance has a certain degree of beauty, is resistant to corrosion, can maintain a good quality of appearance for a long time, and the material is environmentally friendly, and the waste is recyclable.
Metal Industry.
Indium ingot, indium wire, indium foil, indium sheet, indium ring, indium disk, indium plate, indium target, indium strip, indium slag, gallium metal, vanadium metal, germanium ingot and other metal products..
Tantalum wire, tantalum tube, tantalum rods, tantalum crucible, niobium wire, niobium tube, niobium rods.CIF FOB
Steel rebars & billets.Manufacturer
We can supply used rail R50 and R65 Composition: C - 0.54-0.82 %, SI -0.18-0.40%, MN - 0.60-1.05%, S - 0.04% maximum P - 0.035% maximum AS: 0.01% maximum of mass share 1. Technical terms: used rail R50-R65 2. Specifications and Chemical Composition: Used Rail: R50 (51.67KG/Meter, GOST 7173-55), Used Rail: R65 (64.72KG/Meter, GOST 8161-75). Size & Weight: Length: 12meter ~ 12.5meter Maximum or less according tobuyer's instruction; Expenses on seller Width: 5.5 inches ; Weight: 64.72Kg. No fishplates or steel pieces or bolts are attached to the used rails. All rails are clean and straight. No pitting. Only atmospheric rust. No heavy rust. It is mandatory that rails must be cut into length 1.5 meter (max.) before shipment.
Packaging: 100cm X 80cm X 100cm. Bale weight: 25 to 30kg. We pack 30 bales in a bundle making total bundle weight of 750kg to 900kg. Products Pure Aluminum UBC Scrap Grade AA Series GB/T1196-2002 Product Origin EU Al (min ) 99%-99.97% Alloy Or Not: Non-Alloy Color: Multicolor cans Secondary or not: Non-secondary
Cathode copper refers to high-purity copper produced through the electrolytic refining process. Cathode copper is characterized by its high electrical conductivity, excellent thermal conductivity, and good formability. Standard: ASTM, GB, DIN, BS, EN, JIS We have copper wire scrap in Large quantity we are ready and able to supply 2000Mt a month and more. our copper wire scrap is 99.78% pure. quality brass wire Wire diameter: 0.30mm, 0.25mm, 0.20mm Weight/ spool: 3 kg, 5 kg, 7 kg, 15 kg, 20kg Tensile strength: 1000 N/ mm2, 900 N/ mm2, 500 N/ mm2, 450 N/ mm2, N/ mm2 Packing: shrink wrapped+ carton+ pallet to resist moisture, quake, and corrosion. Application: used on low speed wire cutting machines like Agie- charmilles,� Sodick, Mitsubishi and Makino. Usage: Electrical, light industry, machinery, building industry, national defense industry Copper Scrap is industry a important sources of the raw materials All kinds of can be recycled Recycling waste production with copper Specification: Copper WIRE SCRAP, ( Millberry) 99.78% at a purity of 99.78% min. 99.78% Max. COPPER: 99, 9% CARBON: 0.03% COBLET: <0, 001 IRON: 0, 005% PHOSPHORUS: <0, 01% SULPHUR: <0, 01% ZINC: 0, 003% We offer the best copper wire at a very affordable price. copper wire scrap are ready for shipment.
We offer Aluminum Scrap 6063 is (Briquetted form 15 inch x 15 inch & o25cm x 25cm x 20cm and weight range 25 Kg to 35 Kg) mill finish / anodized.Material contains no attachment, and no chips in the bundles/ briquettes. Material is only white and not painted No plastic content, No Iron related materials. Dimension of briquette only 15 inch x 15 inch and or 25cm x 25cm x 20cm and weight range 25 Kg to 35 Kg. Products Pure Aluminum Extrusion Scrap Grade AA Series 6000, 6061, 6063 Product Origin EU Al (min ) 99%-99.97% Alloy Or Not: Non-Alloy Color: Silvery white metal Secondary or not : Non-secondary
We offer Aluminum Scrap 6063 is (Briquetted form 15 inch x 15 inch & o25cm x 25cm x 20cm and weight range 25 Kg to 35 Kg) mill finish / anodized.Material contains no attachment, and no chips in the bundles/ briquettes. Material is only white and not painted No plastic content, No Iron related materials. Dimension of briquette only 15 inch x 15 inch and or 25cm x 25cm x 20cm and weight range 25 Kg to 35 Kg Products Pure Aluminum Extrusion Scrap Grade AA Series 6000, 6061, 6063 Product Origin  EU Al (min ) 99%-99.97% Alloy Or Not: Non-Alloy Color: Silvery white metal Secondary or not: Non-secondary
Aluminium wheel scrap consists of discarded aluminium alloy wheels, which are highly recyclable and ideal for producing aluminium ingots. These scraps have a high aluminium content and are primarily used in industries requiring lightweight and durable materials. Aluminium wheel scrap refers to used or damaged aluminium alloy wheels that are recycled to produce aluminium ingots. This scrap is popular due to the high aluminium content, typically around 99%, and its potential for reuse in various manufacturing sectors. Features: High Purity: Contains 99.9% aluminium, making it ideal for further processing and refining. Applications: Mainly used in the production of lightweight, corrosion-resistant products such as automotive parts, aerospace components, and construction materials. Environmental Benefits: Recycling aluminium wheel scrap reduces the need for virgin aluminium production, saving energy and reducing carbon emissions. Industrial Use: Industries involved in vehicle manufacturing and construction highly value aluminium wheel scrap for its ease of melting, fast processing, and significant cost savings compared to new aluminium.
For these Inconel and Incoloy Olets and cost-effective procedures for molding nickel alloy components to shape and polish, grinding is preferred over machining, water-jet, or laser. The grinding wheels in Inconel and Incoloy Olets are less impacted by work hardening and remain sharp and long-lasting due to the hardness of the abrasives utilized. After reaching full maturity by induction heating to 1,300 �?�°F (704 �?�°C), Inconel Olets can be rolled-threaded without increasing grain size. Inconel Outlet Fittings are used in severe situations because they resist oxidation at high temperatures. Inconel or Incoloy Outlet Pipe Fittings work-harden during machining, providing them with more strength and gumminess than steel when improved temperature performance or strength is required. A global steel manufacturer produces Inconel and Incoloy Olets using high-quality raw materials and cutting-edge technology and machinery. These items come in a variety of sizes, shapes, and styles to meet the needs of diverse industries. Our high-quality Inconel and Incoloy Olets are a low-cost, high-quality replacement for a wide range of typical goods. In several industries, Inconel and Incoloy Olets are employed. Our engineers are working to increase the quality of Inconel and Incoloy Olets while also cutting down on production time to ensure faster delivery. Fabrication, Oil & Gas, Fertilizers, Electronics, Construction, Chemical Industries, Plumbing, Power Plants, Modern Architecture, Petroleum Industry, General Purpose Applications
Syphon Size 1/2 inch Condensate Pot Size Pipe size 2, 3, 4, 6 and larger size upon request. Standard length: Pipe length 8, 10, 12, and larger length upon request. Pipe Schedule: 40, 80, 160, seamless pipe. NPT as per ANSI B2.1 taper pipe thread furnished. Socket weld as per ANSI B16.11 Butt weld as per ANSI B16.9 Working pressure: 6000 PSIG (41.34 MPa). Snubber Size Bore sizes 3/4 to 10 in diameter Travel ranges from 5 to 20 Load capacities from 738 lbs. to 187,900 lbs. Pipe Clamps 1/2 -18 Inch Types Condensate Pot, Air Header, Pipe Clamp, Quick Release Coupling, Syphon Tube / Pipe, Pipe Clamp, Snubber, Lock Nut For O-seal, Gauge Snubber, Thermocouple, Thermowell, Gauge Adaptors, Gauge Saver, Pressure Gauge Accessories, Mini Ball Valve, Over-Pressure Protector, Cooling Tower, Adjustable Snubber Application Power/ gas/ petroleum/ chemical/ metallurgy/ shipbuilding etc. Air Header Size Inlet Connection Size:1/2, 3/4, 1 inch Raised Face, Female NPT, BSPT, BSPP 2,3 & 4. inches Drain Connection Type:Female NPT, BSPT, BSPP Drain Port Size:1/2, 3/4, 1 Working Pressure:6000 psi [413 bar] Test Certificates EN 10204/3.1B Raw Materials Certificate 100% Radiography Test Report Third Party Inspection Report, etc
Duplex Steel Instrumentation Accessories are frequently utilized in industrial applications, such as the manufacture of seawater heat exchangers and chemical containers for use in high-concentration chloride environments, due to their great combination of superior mechanical qualities and high corrosion resistance. In the production of duplex stainless steel items, welding is widely used. It has properties such as heat resistance, general corrosion resistance, pitting resistance, stress corrosion cracking resistance, crevice corrosion resistance, extended serviceability, high tensile strength, high yielding strength, and anti-corrosive body, among others. Duplex Steel Instrumentation Accessories come in a variety of shapes and sizes, and they are employed in the plumbing system for a variety of tasks and purposes. Duplex Steel Instrumentation Flare End Fittings are high-performance accessories made from the most common duplex stainless steel grade, which contains molybdenum, nitrogen, and nickel. These are austenitic-ferritic steel accessories with excellent corrosion resistance and strength. This valve alloy is also resistant to localized corrosion, such as pitting, crevice corrosion, and intergranular corrosion. These Instrumentation Condensate Pots are susceptible to chlorides stress corrosion cracking and have superior high-temperature oxidation resistance. In services such as brackish water, marine conditions, and closed-loop water systems, these valves have exceptional resistance. In comparison to other grades, this valve grade is extremely ductile and robust
Specification of SS Instrumentation Accessories Syphon Size 1/2 inch Condensate Pot Size Pipe size 2, 3, 4, 6 and larger size upon request. Standard length: Pipe length 8, 10, 12, and larger length upon request. Pipe Schedule: 40, 80, 160, seamless pipe. NPT as per ANSI B2.1 taper pipe thread furnished. Socket weld as per ANSI B16.11 Butt weld as per ANSI B16.9 Working pressure: 6000 PSIG (41.34 MPa). Snubber Size Bore sizes 3/4 to 10 in diameter Travel ranges from 5 to 20 Load capacities from 738 lbs. to 187,900 lbs. Pipe Clamps 1/2 - 18 Inch Types Condensate Pot, Air Header, Pipe Clamp, Quick Release Coupling, Syphon Tube / Pipe, Pipe Clamp, Snubber, Lock Nut For O-seal, Gauge Snubber, Thermocouple, Thermowell, Gauge Adaptors, Gauge Saver, Pressure Gauge Accessories, Mini Ball Valve, Over-Pressure Protector, Cooling Tower, Adjustable Snubber Application Power/ gas/ petroleum/ chemical/ metallurgy/ shipbuilding etc. Air Header Size Inlet Connection Size:1/2, 3/4, 1 inch Raised Face, Female NPT, BSPT, BSPP 2,3 & 4. inches Drain Connection Type:Female NPT, BSPT, BSPP Drain Port Size:1/2, 3/4, 1 Working Pressure:6000 psi [413 bar] Test Certificates EN 10204/3.1B Raw Materials Certificate 100% Radiography Test Report Third-Party Inspection Report, etc
Specification of Duplex Steel Instrumentation Fittings Imperial Size 1/2 to 2 Size 1/16 OD to 2 OD, 2mm OD to 50mm OD Thread NPT, BSP, BSPT, UNF, ISO, SAE, MS, AN, weld ends etc. Pressure Rating 6000PSI for Stainless Steel, 300/1000/3000PSI for Brass Temperature Ratings Up to 1000F (537C) Types Tube to Union, Tube to Male, Tube to Female, Instrument Pipe Fittings, Accessories Application Power/ gas/ petroleum/ chemical/ metallurgy/ shipbuilding etc. Our service Nace Mr 01 75 Sour Service Impact Test As Per Ug 84 Macro Structure Analysis Hydrogen Induce Cracking Test (Hic) Sulphide Stress Cracking Test (Sscc) Cryogenic Services (Cryo),hydrogen Services (H2) Helieum Leak Test Dye Peniterant Test (Dp) Magnetic Partius Test (Mp) Post Weld Heat Treatment (Pwht) Ultrasonic Test (Ut) Hydro Test, Etc. Test Certificates EN 10204/3.1B Raw Materials Certificate 100% Radiography Test Report Third Party Inspection Report, etc Production Technique Forged/ Heat treated and machined.
Duplex steel instrumentation fittings have higher mechanical strength and higher ductility. Moreover, these fittings have a good ability to resist stress corrosion cracking, ranging from nominal to subzero temperatures. These duplex steel instrumentation fittings are tested under different testing measures to ensure their hardness, mechanical strength, reliability, and functionality in adverse applications. These Duplex Steel Instrumentation Fittings exhibit a low coefficient thermal expansion, sulfide stress corrosion cracking resistance (sour-gas environment), high thermal conductivity, etc. Duplex Steel Instrumentation Fittings are well demanded due to their high mechanical strength and good welding ability. Duplex Steel Instrumentation Fittings are usually used in heat exchangers, tubes, and pipes for the production and handling of gas and oil, mechanical and structural components, power industry FGD systems, cargo tanks, vessels, piping and welding consumables for chemical tankers, etc. Duplex Steel Instrumentation Fittings have a high strength means that the range of 0.2% PS for the current duplex grade is from 400-500 MPa. Our Duplex Steel Instrumentation fittings are available in various types like male elbow, female elbow, front ferrule, back ferrule, ferrule nut, bulkhead nut, union elbow, union tee, male branch tee, male-run tee, female-run tee, female branch tee, male connector, female connector, bulkhead male connector, bulkhead female connector, union cross, bulkhead union, ferrule nut, etc. We conduct various tests on our products to ensure they are error-free and suitable for use in various industries
Steel and metal, metal scrap, including ferrous and non ferrous materials.Logistics
Electroplating service of nickel, tin, copper, silver, nickel chrome plating.
Machinery and wire.
