Baosteel Released Carbon Steel Flats Futures Price Policy for April 2020 On March 10, 2020, Baosteel released carbon steel flats futures price policy for April 2020 based on price policy for March 2020. (Following prices exclude VAT unless specified) I HR (Baoshan base, Qingshan base, Dongshan base and Meishan base) Base price: down 50 yuan/t II Heavy Plate (Baoshan base, Dongshan base) Base price: unchanged III Section Steel (Qingshan Base) Base price: unchanged IV Pickled coil (Baoshan base, Qingshan base, Dongshan base and Meishan base): Base price: down 100 yuan/t
Sphere Shaped Nickel Plated Magnets ; Size: OD 5mm :216 Pieces ; Features: Max operating temp : 80°C ; Grade: N35 ; Coating: Nickel -Ni; Directions of Magnetization :Top - North Pole / Bottom - South Pole and Thickness Magnetized. Nickel Coated Magnets have many industrial, educational and household uses.It is best to Nickel coated for long-term maximum energy output and usage. These Magnets are highly resistance against demagnetization.
Feature: -Max operating temp 80°C -Grade: N35 -Coating: Nickel -Ni -Directions of Magnetization :Top - North Pole / Bottom - South Pole and Thickness Magnetized. Nickel Coated Magnets have many industrial, educational and household uses .It is best to Nickel coated for long-term maximum energy output and usage. These Magnets are highly resistance against demagnetization.
Feature: -Max operating temp 80°C -Grade: N35 -Coating: Nickel -Ni -Directions of Magnetization :Top - North Pole / Bottom - South Pole and Thickness Magnetized. Nickel Coated Magnets have many industrial, educational and household uses. It is best to Nickel coated for long-term maximum energy output and usage. These Magnets are highly resistance against demagnetization.
Ferrite magnets are made of a composite of iron oxide and barium or strontium carbonate.These materials are readily available at a lower cost than other types of materials used in permanent magnets making it desirable due to the lower cost. Ceramic magnets have a good balance of magnetic strength, resistance to demagnetizing and economy. They are the most widely used magnets today.
500 Matric Ton available in Dubai cash and carry price LME Cash Price less 2.5% to the buyer. -
In ferrous we mainly deal in HMS1 & 2 Material Specification Heavy Melting Scrap (HMS 1& 2) ,80%HMS 1 & 20 % HMS 2 confirming to ISRI 200-206 Steel scraps shall be totally free from any types of radiation, bombs, arms and ammunition, mines, shell, cartridges, sealed containers, gas cylinders, explosive shells or explosive materials in any form either used or otherwise as per the specification below. HMS 1 â?? ISRI Code 200: heavy melting steel. Wrought iron and/or Steel scrap ¼ inch or steel scrap ¼ inch and over in thickness. Individual pieces not over 60 x 24 inches. HMS 1 â?? ISRI Code 201: heavy melting steel 3 feet x 18 inches. Wrought iron or steel scrap ¼. HMS 1 â?? ISRI Code 202: heavy melting steel 5 feet x 18 inches. Wrought iron or steel scrap ¼. HMS 2 â?? ISRI Code 203: heavy melting steel. Wrought iron or Steel scrap, Black and Galvanized. 1/8 inch and over in thickness, charging box size to include material not suitable as no.1 heavy melting steel. HMS 2 â?? ISRI Code 204: same as ISRI 203 but max size 36Ã?18 inches. HMS 2 â?? ISRI Code 205: same as ISRI 204 but free of sheet iron or thin-gauged material. HMS 2 â?? ISRI Code 206: same as ISRI 204, but max size 60 x 18 inches 1.High quality with best price 2.Well reputation 3.Factory with strong supply ability 4.Prompt shipment
Mn 37 % SiO2 15-20 % H2O 11 % Al2O3 2.15 % P 0.2 % CaO 4-5 Fe 1.3-1.4 S 0.2-0.25 Size 20-0 mm
Zinc
Angles
Galvanized GI, CRC
Deformed Bars
Magnet Assy is located behind target, activated electronic motion in the plasma that improved efficiency by improving the uniformity of the deposition. Cathode role of the target material (Ti, Al, W, Ta, Cu, etc.) to be deposited on a substrate, pulls the Arion in plasma.
- Magnet assemblies are made up of steel parts and a ceramic magnet, bonded together with epoxy. - Max pull is tested on a ½� thick and flat machined steel plate. But the actual pull should be much smaller if your steel is thinner, rough, rusty, coated or not very flat. For any critical applications, three-time safety factor is strongly recommended. - Besides standard models listed bellow, we can make assemblies based on custom designs. - Applications include magnetic holding, lifting, antenna mounting, positioning, retrieving and more.
Magnet Assy is located on the Target in deposition processing (PVD process) in pre-processing of the semiconductor wafer chips manufacturing. Place the substrate(wafer)on the surface of the MCA E-chuck. Its role is to create the thin film off the Target in a plasma vaccum with its magnetic force. It has a significant role of the wafer thin film creating
Seal is used to latch the openable door and fixed glass at 180 deg to avoid any water leakage through it. Developed/Engineered from top quality grade of PVC Extrution. Durable and Resistant to the extreme change in temperature. Ideal for usage in shower cubicles for sealing the edges to prevent water leakage. RoHs Certified Available for 8mm, 10mm and 12mm Glass. Available in various lengths: 2.2Mtr., 2.4Mtr. (Can be supplied as per customer's requirement upto 3 meters)
Co: 99.97% FSSS: 1.6um Mesh : -400 Qty : 1ton minimum
Co: 99.97% FSSS: 1.6um Mesh : -400 Qty : 1ton minimum
Graphite Electrodes for Steel plants. 200mm to 700mm diameter.
product: steel quantity : 500 000 mt shipping terms: fob destination port : mersin port-turkey looking for buyers from worldwide
