Aluminum alloying tablets are used to adjust the content of metallic element in the manufacture of high quality aluminum alloys, providing the following benefits: - high element recovery rate (typically over 95%) - rapid dissolution at normal casthouse operating temperatures - accurate and clean addition - concentrated form means reduced inventory, transport and storage costs. Two or three tablets wrapped directly by aluminum foil. 20kgs in a cardboard.
Application AlTiB produces an equiaxed fine grain structure in cast Aluminum Alloys, providing the following benefits: -Improved homogeneity -Uniform distribution of elements -Elimination of hot tearing -Enhanced response to heat treatment -Superior mechanical properties -Increased machine ability. Size Available in the form of: 1. Cut rod: diameter 9.5mm length: 10¡ª1000mm 2. Coil: 180kgs/coil 3. Small ingot: 250g/pc Also can produce as per customer require.
Application Hypoeutectic and eutectic modification of Al-Si casting alloys Specifications AlSr3.5% AlSr10% AlSr up to 15% Size Available in the form of: 1. Cut rod: diameter 9.5mm length: as you require 2. Small ingot: 250g/pc.
Alloy with high and stable resistance, corrosion resistance, surface oxidation resistance is good, a better under high temperature and seismic strength, good ductility, good workability and weldability, is widely used in industrial electric furnace, metallurgy, household appliances, machinery manufacturing, heating element and resistor varistor other material.
Alloy with high and stable resistance, corrosion resistance, surface oxidation resistance is good, a better under high temperature and seismic strength, good ductility, good workability and weldability, is widely used in industrial electric furnace, metallurgy, household appliances, machinery manufacturing, heating element and resistor varistor other material.
Alloy with high and stable resistance, corrosion resistance, surface oxidation resistance is good, a better under high temperature and seismic strength, good ductility, good workability and weldability, is widely used in industrial electric furnace, metallurgy, household appliances, machinery manufacturing, heating element and resistor varistor other material.
Alloy with high and stable resistance, corrosion resistance, surface oxidation resistance is good, a better under high temperature and seismic strength, good ductility, good workability and weldability, is widely used in industrial electric furnace, metallurgy, household appliances, machinery manufacturing, heating element and resistor varistor other material.
Alloy with high and stable resistance, corrosion resistance, surface oxidation resistance is good, a better under high temperature and seismic strength, good ductility, good workability and weldability, is widely used in industrial electric furnace, metallurgy, household appliances, machinery manufacturing, heating element and resistor varistor other material.
Aluminium alloy
Aluminium flagpole
Aluminum alloy
Aluminum alloy
Machining titanium alloy Export wood cases package.
Ferro alloys
High quality, low price.
Ferro alloys, sponge iron, iron scrap Ferro silicon, silico manganese
Advantages: * High density (17.0~18.5g/cm3). * Good machinability. * Good mechanical properties * High modulus of elasticity * High absorption capacity against x-rays and v-rays * Harmless to the health and environment.Applications: * Protection shields for nuclear radiation * Balancing weights * Substitutional material for Uranium * Electroheat upsetting anvil block * Balls in bomb. * High voltage electrical contact * Electrodes for Resistance WeldingProduct Standard: ASTM B 777 99.
Advantages: * high density (17.0~18.5g/cm3). * good machinability. * good mechanical properties * high modulus of elasticity * high absorption capacity against x-rays and v-rays * harmless to the health and environment.Applications: * protection shields for nuclear radiation * balancing weights * substitutional material for uranium * electroheat upsetting anvil block * balls in bomb. * high voltage electrical contact * electrodes for resistance weldingproduct standard: astm b 777 99 . Export cartons
Cube2--C17200 (CDA 172) Beryllium Copper is the most commonly utilized Copper Beryllium alloy and is notable for its highest strength and hardness compared to commercial copper alloys. C17200 alloy contains appr. 2% of beryllium and achieves its ultimate tensile strength can exceed 200 ksi, while the hardness approaches Rockwell C45. Meanwhile, the electrical conductivity is a minimum of 22% IACS in the fully aged condition.C17200 also exhibits exceptional resistance to stress relaxation at elevated temperatures. International Specification: Rods/Bars/Tubes: ASTM B196,251,463; SAE J461,463; AMS 4533,4534,4535; AMS4650,4651; RWMA Class 4 Strips:ASTM B194, AMS4530,4532; SAE J461,463 Sheets: ASTM B194 Wires:ASTM B197, AMS4725, SAE J461,463 Plates:ASTM B194, SAE J461,463; AMS4530,4533,4534,AMS4650,4651; RWMA Class 4. European Standards: CuBe2, DIN 2.1247, CW101C to EN Note: ASTM: American Society for Testing and Materials SAE: Society of Automotive Engineers AMS: Aerospace Materials Specification (Published by SAE) RWMA: Resistance Welder Manufacturers' Association Note: Unless otherwise specified, material will be produced to ASTM. Available Sizes: Custom Diameter & Sizes, Random Mill lengths Available Products (forms): Round bars, Round strips, Round wires, Round tube, Flat bars, Square bars, Rectangular bars, Hexagon bars, Plates, Sheets, Coils Custom shapes are available upon request. Chemical Composition: Be: 1.85-2.10% Co+Ni: 0.20% Min. Co+Ni+Fe: 0.60% Max. Cu: Balance Note: Copper plus additions equal 99.5% minimum Typical Physical Properties: Density (g/cm3): 8.36 Density before age hardening (g/cm3): 8.25 Elastic Modulus (kg/mm2 (103)): 13.40 Thermal Expansion Coefficient (20 ípC to 200 ípC m/m/ípC): 17 x 10-6 Thermal Conductivity (cal/(cm-s-ípC)): 0.25 Melting Range (ípC): 870-980 Note: 1). the units are based upon Metric. 2). the typical physical properties apply to age hardened products.
CuCo1Ni1Be--CW103C (DIN 2.1285) Cobalt Nickel Beryllium Copper Alloy contains approximately 1% Cobalt, 1% Nickel and 0.5% Beryllium. After hot forging and heat treatment processes this material gains considerably hardness, electrical and thermal conductivity as well. It is possible to have different combinations of electrical conductivity and hardness by changing the heat treatment conditions;CuCo1Ni1Be also Offers good strength and hardness characteristics coupled with conductivity in the range of 45-60 percent of copper with ultimate tensile and hardness properties approaching 140 ksi and RB 100 respectively, all of its properties are quite the same as CuCo2Be-C17500 and CuNi2Be-C17510. International Specification: Rods/Bars/Tubes: ASTM B441, SAE J461,463; RWMA Class 3 Sheets: ASTM B534 Wires: ASTM B441 Plates: ASTM B534, SAE J461,463; RWMA Class 3 European Standards: CuCo1Ni1Be, DIN 2.1285; CW103C to EN Note: ASTM: American Society for Testing and Materials SAE: Society of Automotive Engineers AMS: Aerospace Materials Specification (Published by SAE) RWMA: Resistance Welder Manufacturers' Association Note: Unless otherwise specified, material will be produced to ASTM.
