Organic fertilizer bio plus activator, kalimantan steam coal, wood charcoal, high speed diesel, crude.Education - international student placement & guardianship programme
1) made from 100% mangrove wood & fully carbonized 2) longer buring time and higher heat combustion (more than 3 hours burning time) 3) less smoke, less spark and is odourless 4) no added chemical additives and is purely good for health 5) packing in pe + pp begs of 20 kg 6) size: diameter of 2 - 4cm and a length of 20 - 30cm Packing in pe + pp begs of 20 kg Size: diameter of 2 - 4cm and a length of 20 - 30cm
1) mix grade of a+b+c in carton box 2) burning time: long hours (> 3 hours) 3) less smoke, less spark and is odourless 4) no added chemical additives and is purely good for health 5) packing: carton box Packing per carton: 20/25 kg
Wood chips from tree cutting from Malaysia. All tree cuttings are certified by the local authority. Consist of hard woods with daily capacity of 200 Tons. 450 Kg Jumbo Bag or Open Top 40' Container
Core steel plate Specification for core steel plate 1.0Scope 1.1 this specification covers the grain oriented electrical steels are iron-silicon alloys that provide Low core loss and high permeability needed for more efficient and economical electrical Transformers. Cold rolled grain oriented (crgo) grades of electrical steel are typically used For transformer cores and large generators. 2.0Application 2.1 the cgro is used regularly for cores in transformers. 3.0Standard 3.1 this specification is prepared by taking guidance from bs 601:1973 4.0Material 4.1 cold rolled grain oriented (crgo) grade m5, moh, zdkh as per bs 601:1973 and Equivalent to jis c 2553 5.0Properties 5.1 specifications and typical electrical and magnetic properties (see appendix 1) 6.0Dimension and tolerance 6.1 dimension : as per the purchase order with the tolerance as given table below Tolerance on width Nominal width (mm) OverUp to and includingTolerance (mm) 0150+ 0 0.3 150500+ 0 0.5 001000+ 0 1.5 Tolerance on length Nominal width (mm) OverUp to and includingTolerance (mm) 02000- 0 + 1.5 2000>2000- 0 + 2.0 Tolerance on length The tolerance on the mean thickness, measured by contact micrometer, for any coil shall be + 0.03 mm from the nominal thickness. Tolerance on edge burr The tolerance on edge burr not to exceed 0.05mm. Tolerance on edge camber Edge camber is the lateral departure of the edge of the strip from a straight line forming a chord, refer figure a: Tolerance on edge camber of strip in coil shall not exceed 2 m in 2000 mm and shall be measured against a straight edge using a 2000 mm length cut from a coil. 7.0References (1) bs 601: 1973, steel sheet and strip magnetic circuits of electrical apparatus. As provided above
Silicon steel 1.0 scope 1.1 this specification covers the grain oriented electrical steels are iron-silicon alloys that provide Low core loss and high permeability needed for more efficient and economical electrical Transformers. Cold rolled grain oriented (crgo) grades of electrical steel are typically used For transformer cores and large generators. 2.0application 2.1 the cgro is used regularly for cores in transformers. 3.0standard 3.1 this specification is prepared by taking guidance from bs 601:1973 4.0material 4.1 cold rolled grain oriented (crgo) grade m5, moh, zdkh as per bs 601:1973 and Equivalent to jis c 2553 5.0properties 5.1 specifications and typical electrical and magnetic properties (see appendix 1) 6.0dimension and tolerance 6.1 dimension : as per the purchase order with the tolerance as given table below Tolerance on width Nominal width (mm) Overup to and includingtolerance (mm) 0150+ 0 0.3 150500+ 0 0.5 001000+ 0 1.5 Tolerance on length Nominal width (mm) Overup to and includingtolerance (mm) 02000- 0 + 1.5 2000>2000- 0 + 2.0 Tolerance on length The tolerance on the mean thickness, measured by contact micrometer, for any coil shall be 0.03 mm from the nominal thickness. Tolerance on edge burr The tolerance on edge burr not to exceed 0.05mm. Tolerance on edge camber Edge camber is the lateral departure of the edge of the strip from a straight line forming a chord, refer figure a: Tolerance on edge camber of strip in coil shall not exceed 2 m in 2000 mm and shall be measured against a straight edge using a 2000 mm length cut from a coil. 7.0references (1) bs 601: 1973, steel sheet and strip magnetic circuits of electrical apparatus.
Timber product, hardwood, logs or sawn timber.
Red sandal wood.Export
Wood chips from tropical tree.
Mangrove charcoal, wooden flooring.
Biomass wood pellets (rubber wood, tropical wood, pine wood).
Agar wood.Manpower
Wood pellet and chips for biomass production..Packaging and shipping
Palm oil, charcoal, pure honey.Clearing agent, transportation
Indian red sandal wood, indian rosewood.Air freight, sea freight, land transport, custom clearance, warehousing
Sawn timber such as red meranti, redwood, mixed hardwood, balau.Shipment
Wood, palm kernel shell.
Gaharu.Legal & finance
Charcoal, RBD palm olein, LED flooring, cement, steel, power banks.Ground logistics
Sawn & timber wood.
