Silicon steel 1.0 scope 1.1 this specification covers the grain oriented electrical steels are iron-silicon alloys that provide Low core loss and high permeability needed for more efficient and economical electrical Transformers. Cold rolled grain oriented (crgo) grades of electrical steel are typically used For transformer cores and large generators. 2.0application 2.1 the cgro is used regularly for cores in transformers. 3.0standard 3.1 this specification is prepared by taking guidance from bs 601:1973 4.0material 4.1 cold rolled grain oriented (crgo) grade m5, moh, zdkh as per bs 601:1973 and Equivalent to jis c 2553 5.0properties 5.1 specifications and typical electrical and magnetic properties (see appendix 1) 6.0dimension and tolerance 6.1 dimension : as per the purchase order with the tolerance as given table below Tolerance on width Nominal width (mm) Overup to and includingtolerance (mm) 0150+ 0 0.3 150500+ 0 0.5 001000+ 0 1.5 Tolerance on length Nominal width (mm) Overup to and includingtolerance (mm) 02000- 0 + 1.5 2000>2000- 0 + 2.0 Tolerance on length The tolerance on the mean thickness, measured by contact micrometer, for any coil shall be 0.03 mm from the nominal thickness. Tolerance on edge burr The tolerance on edge burr not to exceed 0.05mm. Tolerance on edge camber Edge camber is the lateral departure of the edge of the strip from a straight line forming a chord, refer figure a: Tolerance on edge camber of strip in coil shall not exceed 2 m in 2000 mm and shall be measured against a straight edge using a 2000 mm length cut from a coil. 7.0references (1) bs 601: 1973, steel sheet and strip magnetic circuits of electrical apparatus.
Type ZXTL - Zircon Sand Crystal Type Zr02 = 63.5~63.97%, Fe203 = 1.31%, Ti02 = 1.25%, Al203 = 0.36%, SiO2 = 32.07%, P205 = 0.01%, Mg0 = 0.13%, K20 = 0.03%, Ca0 = 0.01%, Ti02 = 1.22%, Mn0 = 0.01%, Nb203 = 0.01%, Sn02 = 0.01%, Yb203 = 0.01%, Lu203 = 0.01%, Hf02 = 0.90%, Y203 = 0.01, Th02 = 0.03%, U308 = 0.01%. Supply: 2000~3000MT per month. CNF US$560/MT Type 1: Zr02=47.00, Fe203=2.256%, Ti02=0.79, Hf02=2.17%, Si02=30.71, Al203=1.85, P205=1.12, Na02=0.05, Mg0=0.05, K20=0.21, Zn0=0.05, Sr0=0.05, Ca0=0.09, Mn304=0.06, V205=0.05, Cr203=, Ba0=0.44, Y203=0.49, Er203=0.1, Sc203=0.05 Quantity Supply: 3000~5000MT per month. CNF USD410/MT Packing 25/50kg bag In a big bag of 50kg in 20ft/40ft container.
A bollard is an upright post used to control or direct road traffic, such as posts arranged in a line to obstruct the passage of motor vehicles. Metal Bollard protects various assets from impact and destruction. It is easily removable as metal bollard's locking mechanism is on the base plates. Features: Easy to Install, Excellent barrier between vechicles and people, High gloss paint coated for high visibility.
A bollard is an upright post used to control or direct road traffic, such as posts arranged in a line to obstruct the passage of motor vehicles. Stainless Steel Bollard protects various assets from impact and destruction. It is easily removable. Features: Easy to Install, Excellent barrier between vechicles and people. Stainless Steel Bollard 1000mm (H) with 100mm diameter market and sale by Flexijoint Industrial Marketing & Services, Kuala Lumpur, Malaysia.
We can supply a big quantity of Fridge door packing Soft Magnet scraps for sell.
Origin : South Kalimantan Quantity: (min) 50,000MT û (current max) 100,000MT per month Packing : BULK Loading port : open sea anchorage Taboneo Price : USD66/MT FOB MV Payment term: Non-operative irrevocable, Non-transferable, Revolving Documentary Letter of Credit from Prime Bank : 98% at Sight (after BL, Invoice & COA) at Indonesia loading port + 2% against CCIC/SGS upon arriving at destination port. Not favour to CIQ. Performance bond : The Seller shall issue a non operative 2% Performance Bond Guarantee (PBG) of the LC value, and shall be confirmed irrevocable. Performance Bond Guarantee ONLY applies: 1) To guarantee first shipment being spot trial delivery FOB, if the seller fails in the delivery 2) If long-term contracts and PB used to support the Master LC issued by buyer 3) Performance Bond Guarantee is not used for the purchase of CIF, unless the buyer publishes Master LC, then the seller will back up with PBG. Bulk.
Core steel plate Specification for core steel plate 1.0Scope 1.1 this specification covers the grain oriented electrical steels are iron-silicon alloys that provide Low core loss and high permeability needed for more efficient and economical electrical Transformers. Cold rolled grain oriented (crgo) grades of electrical steel are typically used For transformer cores and large generators. 2.0Application 2.1 the cgro is used regularly for cores in transformers. 3.0Standard 3.1 this specification is prepared by taking guidance from bs 601:1973 4.0Material 4.1 cold rolled grain oriented (crgo) grade m5, moh, zdkh as per bs 601:1973 and Equivalent to jis c 2553 5.0Properties 5.1 specifications and typical electrical and magnetic properties (see appendix 1) 6.0Dimension and tolerance 6.1 dimension : as per the purchase order with the tolerance as given table below Tolerance on width Nominal width (mm) OverUp to and includingTolerance (mm) 0150+ 0 0.3 150500+ 0 0.5 001000+ 0 1.5 Tolerance on length Nominal width (mm) OverUp to and includingTolerance (mm) 02000- 0 + 1.5 2000>2000- 0 + 2.0 Tolerance on length The tolerance on the mean thickness, measured by contact micrometer, for any coil shall be + 0.03 mm from the nominal thickness. Tolerance on edge burr The tolerance on edge burr not to exceed 0.05mm. Tolerance on edge camber Edge camber is the lateral departure of the edge of the strip from a straight line forming a chord, refer figure a: Tolerance on edge camber of strip in coil shall not exceed 2 m in 2000 mm and shall be measured against a straight edge using a 2000 mm length cut from a coil. 7.0References (1) bs 601: 1973, steel sheet and strip magnetic circuits of electrical apparatus. As provided above
Mexico iron ore 65%fe Specifications : fe : 65% rejection below 64% Ai203 : 0.70% 2.5% max rejection over 3.0% Sio2 : 2.50% 3.5% max rejection over 4.5% Sulphur : 0.005% 0.03% max rejection over 0.05% Phosphorus : 0.02% 0.08% max rejection over 0.10% Physical characteristics Below 0.15 mm 25% max. 0 - 10 mm 95 % min. 10mm 5% max Moisture 8% max at 105 degrees centigrade Quantity : 50, 000 mt / month ( 10% more or less ) Delivery : china port Contractual term : 12 months / one year Loading port : mexico port Price : usd 67.00 cnf Price revision : every three months Payment : after the buyer receipt the copy of bill of lading for the shipment. The buyer will open an irrevocable letter of credit for the total value within two bank working days. Lc will be irrevocable & 95% at sight. The remaining 5% of lc value will be remited after cargo arrive the destination port Inspection : sgs at loading port , cost to seller Ciq at discharging port, cost to buyer Bulk
Steel Pipe,Flanges, and Piping accessories. All Material and Size are Covered.
We are offering Brass Electrical Switch Parts, Bras Fasteners, Brass Inserts, Brass Transformer Parts, Brass Electrical Parts, Brass Valves, Brass Sheet Metal Parts, Brass Forging, Brass Precision Components, Brass Cable Glands, Brass Electrical Wiring Accessories, Brass Neutral Links, Battery Parts to give some examples. The offered cluster of parts is decisively designed by our experts utilizing premium quality metal to guarantee its strength at the clients end.
Road studs are commonly known as highway studs or railways studs or highway markers.Road studs are a type of traffic safety product fixed in the middle of lane lines or yellow double-line for, through its retro reflection, reminding drivers to drive their vehicles along with the lanes. Features :- ~ Exceeds ASTM D4280, EN1463-1 of United Kingdom standard; ~ Polymethyl Methacrylate (PMMA) lens ensure highest reflectivity; ~ Economical and durable; ~ High load capacity up to 25 tons; ~ Reflect values of 279 mcd/lux; ~ Reflect range of 0 - 40 degree; ~ Weight approximate 300g; ~ Oil, heat and chemical resistant; ~ Easy to install; Epoxy resin installation method is normally adopted generally for installation of road studs. Two component road stud epoxy adhesive is usually used. Part A and Part B should be mixed thoroughly. To avoid wastage do not mix more epoxy than what will be required in the next 25 minutes (i.e. start with 1 liter only). 8 to 10 studs can be installed per liter of epoxy.
Road studs are commonly known as highway studs or railways studs or highway markers.Road studs are a type of traffic safety product fixed in the middle of lane lines or yellow double-line for, through its retro reflection, reminding drivers to drive their vehicles along with the lanes. Features :- ~ ASTM D2444 standard; ~ Highest reflectivity; ~ High durability; ~ High impact resistance; ~ 90L x 100W x 73H (mm); ~ Heat resistance 62.7 - 2.5 degree Celcius; ~ Easy to install; Aaluminium road stud with Double Amber reflector market and sale by Flexijoint Industrial Marketing & Services, Kuala Lumpur, Malaysia.
