Silicon steel 1.0 scope 1.1 this specification covers the grain oriented electrical steels are iron-silicon alloys that provide Low core loss and high permeability needed for more efficient and economical electrical Transformers. Cold rolled grain oriented (crgo) grades of electrical steel are typically used For transformer cores and large generators. 2.0application 2.1 the cgro is used regularly for cores in transformers. 3.0standard 3.1 this specification is prepared by taking guidance from bs 601:1973 4.0material 4.1 cold rolled grain oriented (crgo) grade m5, moh, zdkh as per bs 601:1973 and Equivalent to jis c 2553 5.0properties 5.1 specifications and typical electrical and magnetic properties (see appendix 1) 6.0dimension and tolerance 6.1 dimension : as per the purchase order with the tolerance as given table below Tolerance on width Nominal width (mm) Overup to and includingtolerance (mm) 0150+ 0 0.3 150500+ 0 0.5 001000+ 0 1.5 Tolerance on length Nominal width (mm) Overup to and includingtolerance (mm) 02000- 0 + 1.5 2000>2000- 0 + 2.0 Tolerance on length The tolerance on the mean thickness, measured by contact micrometer, for any coil shall be 0.03 mm from the nominal thickness. Tolerance on edge burr The tolerance on edge burr not to exceed 0.05mm. Tolerance on edge camber Edge camber is the lateral departure of the edge of the strip from a straight line forming a chord, refer figure a: Tolerance on edge camber of strip in coil shall not exceed 2 m in 2000 mm and shall be measured against a straight edge using a 2000 mm length cut from a coil. 7.0references (1) bs 601: 1973, steel sheet and strip magnetic circuits of electrical apparatus.
Erp, aluminium, timber, jute yarn, jute fiber.
Furniture, carpets, bauxite.
Bonny light crude, siberian light crude, mazut, light cycle oil, bitumen, en590, d2, steam coal, bauxite.
Road studs are commonly known as highway studs or railways studs or highway markers.Road studs are a type of traffic safety product fixed in the middle of lane lines or yellow double-line for, through its retro reflection, reminding drivers to drive their vehicles along with the lanes. Features :- ~ ASTM D2444 standard; ~ Highest reflectivity; ~ High durability; ~ High impact resistance; ~ 90L x 100W x 73H (mm); ~ Heat resistance 62.7 - 2.5 degree Celcius; ~ Easy to install; Aaluminium road stud with Double Amber reflector market and sale by Flexijoint Industrial Marketing & Services, Kuala Lumpur, Malaysia.
River sand, marine sand, dumping sand, silica sand, bauxite sand, ball clay, kaolin clay, aggregates stone.Sourcing products, packaging, shipping
Crushed plastic, ubc (aluminium can scrap), copper scrap, hms 1 iron scrap, recycled fuel oil or furnace oil, stainless steel scrap, palm oil products..
Road studs are commonly known as highway studs or railways studs or highway markers.Road studs are a type of traffic safety product fixed in the middle of lane lines or yellow double-line for, through its retro reflection, reminding drivers to drive their vehicles along with the lanes. Features :- ~ 112L x 91W x 20H (mm); ~ Shank 55mm; ~ Load capacity up to 25 tons; ~ Highest reflectivity lens area 168 square millimeters; ~ High durability; ~ High impact resistance; ~ Grove bottom for better grip and easy installation; Stimsonite ENNIS aluminium road stud with Double Amber reflector market and sale by Flexijoint Industrial Marketing & Services, Kuala Lumpur, Malaysia.
Road studs are commonly known as highway studs or railways studs or highway markers.Road studs are a type of traffic safety product fixed in the middle of lane lines or yellow double-line for, through its retro reflection, reminding drivers to drive their vehicles along with the lanes. Features :- ~ Meets MS 1719: 2003 standard; ~ 103 x 90 x 25 (mm); ~ Economical and durable; ~ Easy to install; Trafico TRC aluminium road stud with Double Amber reflector market and sale by Flexijoint Industrial Marketing & Services, Kuala Lumpur, Malaysia.
Road studs are commonly known as highway studs or railways studs or highway markers.Road studs are a type of traffic safety product fixed in the middle of lane lines or yellow double-line for, through its retro reflection, reminding drivers to drive their vehicles along with the lanes. Features :- ~ 112L x 91W x 20H (mm); ~ Shank 55mm; ~ Load capacity up to 25 tons; ~ Highest reflectivity lens area 168 square millimeters; ~ High durability; ~ High impact resistance; ~ Grove bottom for better grip and easy installation; Epoxy resin installation method is normally adopted generally for installation of road studs. Two component road stud epoxy adhesive is usually used. Part A and Part B should be mixed thoroughly. To avoid wastage do not mix more epoxy than what will be required in the next 25 minutes (i.e. start with 1 liter only). 8 to 10 studs can be installed per liter of epoxy.
Road studs are commonly known as highway studs or railways studs or highway markers.Road studs are a type of traffic safety product fixed in the middle of lane lines or yellow double-line for, through its retro reflection, reminding drivers to drive their vehicles along with the lanes. Features :- ~ Meets MS 1719: 2003 standard; ~ 103 x 90 x 25 (mm); ~ Economical and durable; ~ Easy to install; Epoxy resin installation method is normally adopted generally for installation of road studs. Two component road stud epoxy adhesive is usually used. Part A and Part B should be mixed thoroughly. To avoid wastage do not mix more epoxy than what will be required in the next 25 minutes (i.e. start with 1 liter only). 8 to 10 studs can be installed per liter of epoxy.
Stainless steel scrap, metal scrap , bitumen, gasoline , nuts.
Road studs are commonly known as highway studs or railways studs or highway markers.Road studs are a type of traffic safety product fixed in the middle of lane lines or yellow double-line for, through its retro reflection, reminding drivers to drive their vehicles along with the lanes. Features :- ~ Exceeds ASTM D4280, EN1463-1 of United Kingdom standard; ~ Polymethyl Methacrylate (PMMA) lens ensure highest reflectivity; ~ Economical and durable; ~ High load capacity up to 25 tons; ~ Reflect values of 279 mcd/lux; ~ Reflect range of 0 - 40 degree; ~ Weight approximate 300g; ~ Oil, heat and chemical resistant; ~ Easy to install; Epoxy resin installation method is normally adopted generally for installation of road studs. Two component road stud epoxy adhesive is usually used. Part A and Part B should be mixed thoroughly. To avoid wastage do not mix more epoxy than what will be required in the next 25 minutes (i.e. start with 1 liter only). 8 to 10 studs can be installed per liter of epoxy.
Mild Steel Expandable Safety Barriers are versatile and portable offer solution to pedestrian traffic control problems, suitable to restrict access to temporary prohibited area and often seen their presence in shopping malls, exhibition or event booths functions etc. Features: Compact, portable, lightweight suitable for indoor or outdoor use. Mild Steel Aluminium Hollow Section Expandable Safety Barrier 1300mm (H) x 3000mm (L) market and sale by Flexijoint Industrial Marketing & Services, Kuala Lumpur, Malaysia.
Core steel plate Specification for core steel plate 1.0Scope 1.1 this specification covers the grain oriented electrical steels are iron-silicon alloys that provide Low core loss and high permeability needed for more efficient and economical electrical Transformers. Cold rolled grain oriented (crgo) grades of electrical steel are typically used For transformer cores and large generators. 2.0Application 2.1 the cgro is used regularly for cores in transformers. 3.0Standard 3.1 this specification is prepared by taking guidance from bs 601:1973 4.0Material 4.1 cold rolled grain oriented (crgo) grade m5, moh, zdkh as per bs 601:1973 and Equivalent to jis c 2553 5.0Properties 5.1 specifications and typical electrical and magnetic properties (see appendix 1) 6.0Dimension and tolerance 6.1 dimension : as per the purchase order with the tolerance as given table below Tolerance on width Nominal width (mm) OverUp to and includingTolerance (mm) 0150+ 0 0.3 150500+ 0 0.5 001000+ 0 1.5 Tolerance on length Nominal width (mm) OverUp to and includingTolerance (mm) 02000- 0 + 1.5 2000>2000- 0 + 2.0 Tolerance on length The tolerance on the mean thickness, measured by contact micrometer, for any coil shall be + 0.03 mm from the nominal thickness. Tolerance on edge burr The tolerance on edge burr not to exceed 0.05mm. Tolerance on edge camber Edge camber is the lateral departure of the edge of the strip from a straight line forming a chord, refer figure a: Tolerance on edge camber of strip in coil shall not exceed 2 m in 2000 mm and shall be measured against a straight edge using a 2000 mm length cut from a coil. 7.0References (1) bs 601: 1973, steel sheet and strip magnetic circuits of electrical apparatus. As provided above
Sulphuric acid 98%, aluminium sulphate liquid and solid, sodium silicate liquid & cullet, soda ash dense and caustic soda.Shipment cif, Manufacturer, trading
Soda ash light, aluminium sulphate.
Enamelled copper & aluminium wire (round and rectangular type), float glass..
Aluminium foils.
palm oil aluminium sugar rice jet fuel diesel.
