Copper piping , copper fittings, iron ore , aluminum ingots , nitrile, latex and surgical gloves , crude oil, light cycle oil etc.
Diesel en590 10ppm/15ppm, espo, rebco, light cycle oil, lpg, lng, russian petroleum coke, fuel oil, kerosene, automative gas oil and bitumen..Shipping, air & sea freight forwarders, project cargo, transportation & warehousing.
Radio energie tachogenerator, stegmann encoder, servo-tek encoder, hydraulic vee-packing, asbestos & non-asbestos jointing sheet & heat insulation products & high pressure triplex plunger pump.
Thickened by lithium complex soap, it is made from deeply refined mineral oil with extreme pressure additives, rust and oxidation inhibitors.
Thickened by lithium 12-hydroxystearate, it is made from deeply refined mineral oil with rust and oxidation inhibitors and extreme pressure additives.
This products are high performance, multi-purpose, thermally stable, extreme pressure automotive hypoid gear oils formulated to exceed the severe API GL-5 performance standard.
This products are high performance, multi-purpose, thermally stable, extreme pressure automotive hypoid gear oils formulated to exceed the severe API GL-5 performance standard
-Gibson Brake fluid is a type of hydraulic fluid used in hydraulic brake and hydraulic clutch applications in automobiles, motorcycles, light trucks, and some bicycles. It is used to transfer force into pressure, and to amplify braking force.
Description : 4 Minutes Steel Epoxy is a steel filled fast setting, non shrinking gray colour epoxy adhesive. It offers good gap-filling capabilities and slumping characteristics. It will chemically bond steel, brass, copper, bronze, iron, plastic, wood, concrete and ceramics. Withstands high temperatures and is pressure resistant. Use to repair: worn valve seats, cracked housings, coppers and cylinder heads, gas tank leaks, radiator leaks, torn keyways, stripped threads, worn pulleys, loose screws, etc.
Description : PS-202 PVC Pipe Cement Heavy Duty is a premium grade, high viscosity and clear color adhesive for PVC articles bonding applications. It is an easy-to-apply, fast setting and extra strength formulation. Suitable for waterproof bonding and coupling of rigid PVC, uPVC, cPVC and ABS pipes and fittings, cable conduits, gutters, sewer, drain, waste and vent systems, turf, irrigation and pressure pipe applications. It is safe for drinking water pipes upon complete curing. Model: PS-202 PVC Pipe Cement Heavy Duty
Model: KJB-12 2 Way Fullrange: 48Hz-20KHz Frequency range woofer: LE: 12 Tweeter: HF 44 core Original imported impedance: 8 Sensitivity: 98dB Maximum sound pressure: 132dB Rated power: 400W Coverage angle: 90 X 70 Sheet: 15mm Birchboard Net weight: 21. 7KG Size: 360X400X620MM
Production : From leaf sheath to plate is a whole process and consists of a few steps. Below the different steps are expained from harvesting the material till the disposal of the final product. 1. Harvest Areca palms leaves with the sheaths attached to it fall naturally from the trees three four times a year. By simply picking them up from the ground they are harvested.The amount of sheaths that can be collected from one tree at a time is two - three pieces. The average Areca palm plantation has around 2000 trees. One Areca sheath weights between 200g and 300g and has dimensions of 0,30 m by 1m. 2. Drying After harvest the sheaths need to be dried properly as the sheaths are prone to mold and fungus due to humidity. Normally the sheaths are dried in the open sun. However the time to dry will be approximately 6 months. For speeding up this process a Solar/ LPG drying unit will be designed. The use of an alternative form of fuel, such as LGP, makes it possible to continue production during periods of little sunlight.The dryer unit uses heated air to dry the sheaths. Also an effective drying storage facility will be designed to limit the drying time. 3. Cleaning After the drying process the sheaths need to be cleaned thoroughly in water to remove dirt and dust. This is done manually with a brush. During cleaning the sheaths will absorb water, which will make the sheaths more flexible for pressing. 4. Pressing with heat The sheaths are laid in the machines, whereas it will be pressed into the shape of the dies. These dies will be customizable to make plates of various shapes and sizes. They are heated by an external energy source and will be pressed with a certain amount of pressure, this changes the structure of the sheath particles making them fixed in their shape during pressing. A moisture content above 5% needs to be maintained during pressing or else cracks will appear in the products. Depending of the size of a sheath, multiple products can be pressed. 5. Finishing/ post cure After pressing the plates contain too high moisture content, this means that the plates need to be used immediately or need to be dried. After drying the plates can be stored up to 11 to 12 months.
