Hot-rolled steel plates or steel sheets in various thickness and size. Thickness 1.2mm~75mm. Max width 8ft. Max length 12192mm. Standard size or customized size available for request. Specs: ASTM / JIS G3101 / JIS G 3131 / JIS G3132 / JIS G3113 / BSEN 10025 or equivalent / as per requested. Grade: A36, A516, A588, A283, SS400, SS490, S275, S355, SPHC, SAPH or equivalent / as per requested. Note: Price is indicative only, please contact with us for further discussion on the final quotation.
Copper scrap.
Production : From leaf sheath to plate is a whole process and consists of a few steps. Below the different steps are expained from harvesting the material till the disposal of the final product. 1. Harvest Areca palms leaves with the sheaths attached to it fall naturally from the trees three four times a year. By simply picking them up from the ground they are harvested.The amount of sheaths that can be collected from one tree at a time is two - three pieces. The average Areca palm plantation has around 2000 trees. One Areca sheath weights between 200g and 300g and has dimensions of 0,30 m by 1m. 2. Drying After harvest the sheaths need to be dried properly as the sheaths are prone to mold and fungus due to humidity. Normally the sheaths are dried in the open sun. However the time to dry will be approximately 6 months. For speeding up this process a Solar/ LPG drying unit will be designed. The use of an alternative form of fuel, such as LGP, makes it possible to continue production during periods of little sunlight.The dryer unit uses heated air to dry the sheaths. Also an effective drying storage facility will be designed to limit the drying time. 3. Cleaning After the drying process the sheaths need to be cleaned thoroughly in water to remove dirt and dust. This is done manually with a brush. During cleaning the sheaths will absorb water, which will make the sheaths more flexible for pressing. 4. Pressing with heat The sheaths are laid in the machines, whereas it will be pressed into the shape of the dies. These dies will be customizable to make plates of various shapes and sizes. They are heated by an external energy source and will be pressed with a certain amount of pressure, this changes the structure of the sheath particles making them fixed in their shape during pressing. A moisture content above 5% needs to be maintained during pressing or else cracks will appear in the products. Depending of the size of a sheath, multiple products can be pressed. 5. Finishing/ post cure After pressing the plates contain too high moisture content, this means that the plates need to be used immediately or need to be dried. After drying the plates can be stored up to 11 to 12 months.
Pipes, beams, plates, high tensile plates, oil gas pipes, boiler plate, mesh brc, stainless steel shafts, carbon steel plate, special design iron & stainless teel grill pipes, engineering & construction pipes..
Steel products, steel sheets, steel coils, steel plates, wire meshes, steel pipes, hollow sections, steel tubes, scaffolding, concrete reinforcement fabric, expanded metal, fencing meshes, chequered plates.
Sunflower oil, soybean, palm oil, peanuts, coffee, cocoa beans, rice, sugar, copper scrap, used cooking oil, palm kernel, palm kernel shell, corn seed, barley, coconut oil.
Fresh vegetables like potato.
Bolts & nuts, anchor bolts, u bolts, double nnd stud bolts, hex bolts, stud bolts, hex nuts, flat washers, spring washers, , material, alloy steels: b7, b7m, b6, l7, l7m, l43, etc., stainless steels: b8, b8m, 660a, etc., super duplex: s32750, s32760, etc, , coating system, , electroplated coatings, zinc plating as per astm b633 or astm f1941, cadmium plating as per astm b766 or astm f1941, zinc nickel plating as per astm b841 or astm f1941, , fluoropolymer coatings, whitford xylan 1014.
Our company can supply a varieties of copper piping, copper bar, plate , strip and even rivets to name a few. Material wise we are able to cater for copper, brass, copper nickel, nickel silver and also stainless steel.
Welded ERW Mild Steel Rectangular Hollow Sections. Various thickness & size available. Size range: Rectangular: 38x19mm ~ 150x250mm, Thickness 1.2~9.0mm. Square: 19x19mm ~ 200x200mm, Thickness 1.2~9.0mm. Length: 6M, 12M or as requested. Spec: BSEN10255 / BSEN10219 / ASTM A500 or equivalent / as per requested. Grade: S195T / L275 / S275J0H or equivalent / as per requested. Note: Price is indicative only, please contact with us for further discussion on the final quotation.
Cold-rolled steel coil in various thickness, may request to slit to desired width or cut to desired sheet length. Thickness 0.2~3mm Width max 1220mm. Specs: JIS G3141 or equivalent (Such as EN / ASTM / AS / NZS) / as per requested. Grade: SPCC-SD, SPCC-1B, SPCD-SD or equivalent / as per requested. Note: Price is indicative only, please contact with us for further discussion on the final quotation.
Welded ERW Mild Steel MS Pipe / ERW Pipes / Circular Hollow Section in various thickness & size. Size range:'' ~ 10, Thickness 1.2~9.0mm. Length: 6M, 12M or as requested. Spec: BSEN10255 / BSEN10219 / ASTM A500 or equivalent / as per requested. Grade: S195T / L275 / S275J0H or equivalent / as per requested. Note: Price is indicative only, please contact with us for further discussion on the final quotation.
Steel mesh for concrete reinforcement manufactured from cold-worked reinforcement bar. Size range: A142, A193, A252, A318, A393, A565 (A6~A12) Width 2.2M x Length 6M or as per requested. Specs: MS145 / SS561 or equivalent. Grade: B500A or equivalent. Note: Price is indicative only, please contact with us for further discussion on the final quotation.
Welded ERW Galvanized Pipes or Galvanized Tubes in various thicknesses and size. Size range: up to 10, Thickness 1.2~9.0mm. Length: 6M, 12M or as requested. Spec: BSEN10255 / BSEN10219 / ASTM A500 or equivalent / as per requested. Grade: S195T / L275 / S275J0H or equivalent / as per requested. Note: Price is indicative only, please contact with us for further discussion on the final quotation.
Hot-rolled steel coil in various thickness, may request to slit to desired width or cut to desired plate length. Thickness 1.2mm~25.4mm. Width max 2.428mtr, subject to thickness. Specs: ASTM / JIS G3101 / JIS G 3131 / JIS G3132 / JIS G3113 / BSEN 10025 or equivalent / as per requested. Grade: A36, A516, A588, A283, SS400, SS490, S275, S355, SPHC, SAPH or equivalent / as per requested. Note: Price is indicative only, please contact with us for further discussion on the final quotation.
