Installation power:220v/4200w Air pressure:0.1-0.5mpa Pump: air pressure pump/ 1:22 Speed: 8kg/hr Viscosity: 500-30000cps Capacity: 1gallon Output volume: 300g/min Timers: touch-pad Temperature: 20-220 Nozzle: spray Action: long distance dispensing dot, line Dimension:65 x32 x55cm Weight:37kg
TL-101Tube rolling machine is used for compacting elements in order to increase the density of MgO. It has been well-received in France, Japan and other countries. Functions: 1. The frame of this machine is made out of pig iron casting. The rocker die and tank are integral linear cutting. This machine is also equipped with fine-tuning dial, automatically removing sundries device and automatically cooling system. 2. According to the tube size and your special requirements, we have two types of motor of pinch roller for your choice. They are non-uniform speed (different speed) and uniform speed. The former make the tube better ductility, while the latter applies to the tube with large diameter. 3. When the tube specifications changed, we only need to replace a set of pinch rollers. The pinch rollers can be classified into two categories: high speed steel and tungsten carbide alloy . 4. Automatically stop when clogging. 5. This machine is of small size, low noise, convenient adjustments. 6. Applicable tube: Copper, iron, aluminum, stainless steel, etc. Main technical parameters: 1. Tube diameter after compressing: 5.2mmí½19.0mm 2. The max. diameter before compressing: 21mm 3. The min. length of tube:110mm 4. Efficiency: 18m/min. 5. After compressing, the straightness can reach:1:300 , and the roundness can reach: 0 0.07 .
TL-110 Automatic coil winding machine is used to wind a wire into a circular heater. It applies to wire with different diameters, and both single-wire or double-wire are OK. Functions: 1. The principal axis speed controlled by Japan Mitsubishi transducer. Continuously coils electric resistance and consistent clean-cut ends on the coils. 2. The machine will produce coils with very consistent resistance values and with open inside diameters for easy assembly to the terminal pins 3. When lack of wire or wire is broken, the machine would stop automatically. It also can accumulate the output automatically. 4. Wire with small diameter is usually cut by Galvan magnetism while wire with large diameter is cut by cylinder. 5. This machine is of small size, easy to operate, no operator is required. 6. Wire with large diameter can adopt double-pinch roller type. Main technical parameters: 1 Power supply:220V,50Hz 2 Rated power:500W 3 Main axis speed:0í½2134rpm 4 Pinch roller speed:0½74rpm
TL-120 Semiautomatic tube cutting machine is used to cut copper, iron, stainless steel round tubes Functions: 1. Pneumatic clamping, start cutting automatically. 2. Element rotates, automatically stop when loading finished. 3. Burr-free ends on the tubes, high efficiency, easy to operate. Main technical parameters: 1. Power supply: Triphase 380V, 50Hz 2. Rated power: 0.8KW 3. Air supply: 5í½7kg/cm2 4. Efficiency: 8000pcsí½10000pcs/8h 5. Size LxWxH :800*500*900(mm) 6. Weight: 120kg
TL-340 Cartridge heater coiling machine is used to wind metal wire on the MgO rod. 1 Step motor drive, the pitch can be adjusted. 2 PLC control, easy operation. 3 Stable performance, high production. 4 Easy to change different specification. Main technical parameters: 1. Power supply: Single phase AC220í+10% 50HZ 2. Power: 300W 3. Applicable diameter: í_ 21mm 4. Applicable length: 60í½800mm 5. Size: 1560*600*1220mm
TL-185 M-shaped tube bending machine, is an intelligent machine which can bend various shapes of tubes. Functions: 1. 14 touch screen, operation instruction is attached. 2. PLC automatically controlled, change the parameters according to your requirement. 3. Servo motor controls bending and feeding, the speed, angle and length are all adjustable. 4. Pneumatic clamping, can bend 1½4pcs tubes at a time. Main technical parameters: 1. Power supply: Single-phase 220V, 50Hz 2. Rated power: 4KW 3. Air supply: 5í½7kg/cm2 4. Applicable tube diameter: 6.0mmí½ª¦10mm 5. Size LxWxH:1650*900*1450 (mm) 6. Weight: 1000kg
Used "amada" shearing machine Model: gpx-840 Year: 1993 Max.Cut length: 4m Max.Thickness: 8mm
Used Amada Pega-344 Year of manufacturing: 1986 56st, NO, A/I, 6m
60 Tons Kaiser Machine Year: 1987 Press Force : 630KN Table Dimensions : 810 x 550mm Stroke Adjustable : 10 ~ 80mm Ram Adjustment: 80mm Clearance hole in table : 550 x 140mm Recess in table : 600 x 190 x 50mm Number of stroke on machine continuously adjustable: 65~400 stroke/min Drive Capacity: 11kW Weight of machine: ca 8,000kgs Machine numbers: 131 303 -
Used "Bruderer" Machine Model: BSTA30 30 Ton
BMF Sandwich panel production line Introduction ííííBMFííSandwich panel production line is main equipment that is used to produce sandwich panel í¬ a new building materials which has the features as stable, light, solidity and beautiful appearance. The application of sandwich panels in various usage of large-scale house like supermarket, workshop, warehouse is convenient and fast in building. They also can be offered to construct refrigerator, clearing room .etc feature H plate, tong & groove panel plate production available Corrugated panel with various joints option available EPS or rock wool & glass wool panel available Joint-hidden panel plate with various joint and plate type available Continuous automatic production available Nonstandard panel type as Customer requirement Flexible option for customer practical need PLC(programmable logic controller) combined with touch screen apply convenient and reliable operation Automatic length to cut and count available Complete accessory equipment available Specification External/fix dimensions:Length45000mm í- Width4500mm í- Height2700mm Operation Voltage: 380V Total power: about 32KW Weight: 25ton Production/Operation rate: 0-4.5m/min Material thickness: 0.3-0.8mm Core thickness: 20-300mm Core material: EPS, rock wool and glass wool Control system: Touch screen with PLC, Transducer Sandwich panel production line is main equipment that is used to produce sandwich panel í¬ a new building materials which has the features as stable, light, solidity and beautiful appearance. The application of sandwich panels in various usage of large-scale house like supermarket, workshop, warehouse is convenient and fast in building. They also can be offered to construct refrigerator, clearing room .etc feature H plate, tong & groove panel plate production available Corrugated panel with various joints option available EPS or rock wool & glass wool panel available Joint-hidden panel plate with various joint and plate type available Continuous automatic production available Nonstandard panel type as Customer requirement Flexible option for customer practical need PLC(programmable logic controller) combined with touch screen apply convenient and reliable operation Automatic length to cut and count available Complete accessory equipment available
BMPF-2 Double-chain continuous sandwich panel production line Introduction BMPF-2 continuous sandwich panel line is mainly composed of t, roll forming machine, cutting unit. With the simultaneously polyurethane foaming, this production line is able to realize the continuous sandwich panel production, length to cut by PLC control, speed control by inverter, and polyurethane panel solidifying process is completed in the double-chain laminator. This production line, with the high production rate and automation, accurate synchronization, is extremely appropriate for polyurethane sandwich panel production in a large scale, which is prior in constructing high quality large-size buildings. Specification: Require Specifications of raw materials: Thickness of panel: 0.37-1.2 mm Track Width (Max):1250 mm Weight of uncoil (Max): 5 Tons Inner dia:ª¦500óª¦600 mm Dimension of the sandwich panel available to produce Length: 2 -20 m Width: 900 -1100 mm Thickness (Min) : 30mm Thickness without tile (Max):200 mm Production/Operation rate: 3-10 m/min Length of the whole production line: about120 m Useful length of the double track: 25m Working height: 1200 mm The pressure of pour foaming: 150~200 bar Complete line consist of: (1) Uncoil (Auto) (2) Forming machine (3) Steel/Panel heating machine (4) Heating frame (Move auto) (5) Foaming machine (6) Main engine with double track (7) Heating machine with double track (8) Band saw cutter (9) Automatic stacker (10)Auto electric controller Specification: Require Specifications of raw materials: Thickness of panel: 0.37-1.2 mm Track Width (Max):1250 mm Weight of uncoil (Max): 5 Tons Inner dia:ª¦500óª¦600 mm Dimension of the sandwich panel available to produce Length: 2 -20 m Width: 900 -1100 mm Thickness (Min) : 30mm Thickness without tile (Max):200 mm Production/Operation rate: 3-10 m/min Length of the whole production line: about120 m Useful length of the double track: 25m Working height: 1200 mm The pressure of pour foaming: 150~200 bar Complete line consist of: (1) Uncoil (Auto) (2) Forming machine (3) Steel/Panel heating machine (4) Heating frame (Move auto) (5) Foaming machine (6) Main engine with double track (7) Heating machine with double track (8) Band saw cutter (9) Automatic stacker (10)Auto electric controller
1.Description The machine (with lumped loading device) is suitable for producing large length, compact , bare al/cu wire, and acsr, aluminum alloy wire and sector conductor. 2.Feature 2.1 lumped loading device can increase production efficiency. Adopts 36 steps speed variety gear box, dual capstan device and natural splitting method to enhance the product quality. 2.2 the pay off tension is pneumatic control that can be adjusted by valve. 2.3 the special emergency stopping device can control each bobbin. And the wire broken length is less than 2 meters when stopped. 2.4 we can design pre-twist compacting device for milliken conductor according to customerí»s demands. Electrical control Low pressure components are siemens or schneider brand Dc and ac driven device is eurotherm or siemens brand The touch screen is local or foreigner brands. Packing details: according to exported standard
Features : 1:/mechanical stop and torsion bar to maintain synchronization and high precision. 2:/the machine uses delem nc system, and imported linear transducer, pressure proportional valve and servo motor. 3:/ram stroke(y) and backgauge(x, r, z) are automatically controlled by computer. 4:/backgauge adopts ball-bearing screw and rolling guide, enjoying very high repeat positioning accuracy.
Our Bag cleaning machine is specially designed for cleaning of big-bags (FIBCÆs ,Jumbo bags) The machine has provision for selection of 3 different bags and 3 different programs and equipped with automatic height adjustment according to the length of bag. Following way you can clean the bag: 1. Clean from Top 2. Clean from Bottom 3. Clean from top and Bottom
ST-602 HR: Single needle, plain feed, flat bed, double thread over edging sewing machine for over seaming of light weight to heavy weight jute or PP/PE woven sacks. Specifications: Stitch Range 7-13 mm Over Seam width 10 mm Max thickness of material 12mm Needle size DRx4#32 Working Speed 1800 RPM
This machine is designed for automatically LENGTH cutting of webbings (loops û belts) for F.I.B.CÆs. Also the machine has another function of MARKING. Cutting of the webbings is done by pneumatically operated hot knife. The marking for the sewing place on the webbings are done by pneumatically operated position adjustable marker (refillable). The machine standing orientation is to allow free fall of cut belts into a box. The width of the cutting knife is 65cm. Drive and pressing of the belts are pneumatically controlled rollers. For accuracy purpose machine is vacillated with AC SERVO Motor and Drive with proper torque and hight inertia selection. There is a PLC to control the full process of the machine. The machine is delivered with the inbuilt stand for placing the webbing rolls. To provide good operating condition, the webbings have to be rolled properly. The working output depends on the cut length. The running speed is 65 meters/minute. Cutting and marking is done in 2 seconds. The machine stops automatically when the pre-adjusted total quantity is reached.
Plastic machine
Roto-machine that are the most advanced equipment at home for dozens of enterprises ,which come from different backgrounds
Rotational plastic machine
