SMDY ENERGY SAVING The consumption of water, chemicals, electrical energy, thermal energy and the wasted water are important cost factors in every dye house. With this machine all these factors are dramatically reduced, measured and controlled. Right-first-time in dyeing is now assured by lower differences inside-outside the packages, while savings of electric energy, water, chemicals, steam and compressed air will bring extremely fast payback times over the initial investment cost. New SMDY sizes are from 5 kg to 1500 kg. This machine with this particular pump and inversion group allows to treat polyester textured high density till 0,5 Kg/l as well as very soft material like silk 0,3 kg/l density in order to process every kind of material you can have in your dye house. In particular can dye bobbin 1.8 kg cotton, 2,4 kg acrylic, polyester 4 kg or 10 kg tops or muffs, tow, flock or beams Main advantages are: Possibility to dye with liquor ratio from 1:3.5 using in to out single circulation with material not fully covered. Reduce consumption of chemicals, dyes, water and steam due to low liquor ratio facility. Reduce power consumption of main pump because pipes are designed to avoid losses of pressure so that main pump is exploited in the best way. High efficiency motor and inverter reduces power consumption as well. Possibility to dye also in traditional way: air pad, material fully covered and flow circulation in to out and out to in directions. SMDY FEATURES: Standard design and manufacturing features: Nominal loading capacities from 5 to 1500 kg. Pressure rating of 5.0 kg/cm2, up to 160C tempera- ture, temperature lock at 140C. Construction in AISI 316 stainless steel, for all the part in contact with dyeing liquor. Water protected motors (IEC Standards I). Waterproof electrical equipment Three-level safety systems.. Heat exchangers rated for 15.0 kg/cm2 operating pressure. Heating gradient 5C./minute (range 20-80C steam pressure 6.0 kg/cm2) Cooling gradient 3C./minute (range 130-108C water temp. 15C, pressure 1.5 kg/cm2). Pneumatic lid lifting and lowering. Rapid lid locking system. This is our new SMDY yarn dyeing machine! Yarn dyeing, reinvented! 70% savings on electric energy 30% savings on water, chemicals and utilities Improved yarn dyeing quality Faster payback times Sustainable yarn dyeing.
Agitated Thin Film Dryer Used For The Treatment Of Waste Water Into Salt
Product name:Broiler Floor Raising Equipment Raising Equipment Material:Hot Dip Galvanized Steel; Feature:Manual; Capacity:20000 Chickens; Certification:ISO 9001; Size:1870mm*370mm*370mm; Life time:15-20 Years; MOQ:20000 Chickens; Applicable industry:Chicken Farm; Product advantages:Easy to operate Brand Retech Farming
LZ series sand recycling system has absorbed foreign advanced technology, and designed combined with sand field actual situation. It is widely used in mud purification, artificial sand production line, hydropower station, sand aggregate system, glass raw material processing system, coarse slime recovery, and recycle fine material. Sand recycling system will reduce the loss amounts of fine material effectively, and solve the problems of end product with high fineness modulus and low stone powder content. The fine material can be recycled as high as 95%, with incomparable technical and economic advantages. Working principle Through rubber pipes sand and water mixture is extracted from cleaning tank into slurry pump. The fine sand is collected by the centrifugal force of cyclone, then fed to the polyurethane screen from the apex spray. The 0.16-3mm fine sand and water are efficiently separated through the vibration screen. The waste water will flow back to the return box, through weld chute or pipes flowing to a settling pond. Features & Benefits 1. Recycling 0.16-3mm fine sand. 2. Recycling rate reaches above 95%. 3. The water content of final sand is within 12%-15%. 4. Effectively reduce the loss of fine sand, solve the problem of sedimentation tank accumulates.
Explore Our Automatic Advanced Servo Driven Safety Device / Prevents Insertion and Sticker Labelling Machine for PreFilled Syringes. The design of this machine is very compact despite doing 2 operations at the same time. For More Information: https://www.ambica.co.in/products/Pre-Fillable-Syringes-in-Nest/Safety-Device-Preventis-Insertion-and-Self-Adhesive-Labelling-Machines/automatic-advanced-servo-driven-safety-device-preventis-insertion-and-sticker-labelling-machine/38
Screening Machines
This testing machine adopts a column structure, uses hydraulic loading (computer directly controls the loading speed or rate), and the computer displays the test results. It is convenient to operate and the test readings are accurate and reliable. It can be used for general steel, bolts, anchoring agents and other metal materials. Tension, compression, bending and shear tests, as well as compression and bending tests for general materials, plastics, cement and concrete.
1- Total power: 3.5KW 2- Max. processing size: 2500 X 3660mm (3-50mm) 3- Min. processing size: 200x500mm 4- Glass transfer speed: 3.6 m/min 5- Nozzle moving speed: 8 m/min 6- Sand blasting speed: 20-25m2/h 7- Suitable working pressure: 0.6MPa~0.8MPa 8- Air pressure power: 3m3/min 22kw 9- Occupation area: 6800x1500x3300mm (L* W* H) 10- Weight 1300.00 kgs 11- Automatic gun: 3 PCS , Manual gun: 1PC 12- Mitsubishi PLC + SamKoon Touch Screen. 13- HS CODE: 8424300000
The wheel mill achieves the effect of mechanical force activation through the functions of mechanical mechanics such as rolling, pressing, squeezing, and rubbing. The structure of the original mixed material becomes the active material through the wheel milling, thereby increasing the strength of the product. This is not possible with other types of mixers. Comparable. It is suitable for mixing various wet and dry materials and colloids such as refractory mud, clay, fly ash, slag, tailings slag, molding sand, etc., and is widely used in refractory materials, ceramics, building materials and other industries. The rolling and mixing effect is very good, the noise is low, the production efficiency is high, the energy-saving effect is significant, the sealing performance is good, the environmental pollution is not, and the adaptability is strong. This industrial charcoal powder grinding machine also named the wheel grinder mixer, is specially designed for crushing charcoal pieces into fine charcoal powder. This wheel charcoal grinder mainly can grind charcoal powder and even mix them with the binder, water, etc. Then the processed charcoal powder can be used for further briquetting to make BBQ charcoal or shisha charcoal.
Product Description Application: The plant is applied to products with the melting point below 250C for curing and shaping. Typical applied materials include: Sulphur, Paraffin Wax, Resin, Asphalt, Maleic Anhydride, Trimellitic Anhydride, Salt Stearate, Hot-Melt Adhesives, M-Phenylenediamine, Urea, Rubber and Plastic Auxiliary etc. Working principle: Melting material, through material distributor, drips down to the steel belt which is moving evenly. Under the belt, there are continuous sprayer and cooling device which can cool, solidify and pelletize material on belt as soon as possible. According to material feature and process requirements, outward turning, rotating, reciprocating, gate types are available for your choice. Based on material feature and use requirements, material distributing forms like incontinuous dripping, continuous strip, full-width overflowing are available, and with hemispheric, bar, flake products.
We offer Industrial Air Handling Unit in different designs and capacities. These products can be custom manufactured as per buyer's specifications. Our air handling units have modular design and they are a perfect fabrication of sturdy construction and flexible combination of components to meet the application successfully. The Air Handling Units we offer are widely used in different industries and commercial sectors. Vayuvents delivers high quality Double Decker Air Handling Unit , AHU's, that are reliable, engineered to the highest standards and affordable. Our range of Air Handling Units are designed to create a symbiosis of heat, ventilation and air filtration. The result is a perfectly balanced environment for people and industry.
These are Industrial Heater Blower for Food Industry. As an illustrious corporation of the industry, we are eagerly immersed in presenting a broad gamut of hot air blower to our patrons. specifications Blowers- Centrifugal type blowers with impeller statically & dynamically balanced Heater specification : 50 deg c' to 150 deg c' Heater : 4 kw to 100 kw
Mancoolers are constructed of high quality axial fans and are designed for general industrial use. The mounted units are constructed on a movable base both the inlet and the outlet are provided with screens as standard, and are fabricated to meet OSHA safety requirements. The fanâ??s swivel base allows for a full 360�° rotation, providing airflow from any angle. The stationary units can be adjusted for airflow in any direction and are manufactured with a predrilled base plate for wall, column, ceiling or floor mounting
Fan Size mm / inches Fan Speed RPM Motor (HP) Air Delivery CFM 300 (12) 1440 0.25 600-2000 400 (16) 1440 0.5 2000-2600 400 (16) 1440 0.75 2600-4000 450 (18â??) 2880 1 4000-6000 600 (24) 1440 1 6000-8000 700 (28) 1440 2 8000-9000 800 (32) 960 1.5 9000-11000 800 (32) 960 2 11000-14000 900 (36) 960 3 14000-19500 1000 (40) 960 5 19500-26500
Dust collectors may be of single unit construction, or a collection of devices used to separate particulate matter from the process air. They are often used as an air pollution control device to maintain or improve air quality. Dust collector systems work in general by drawing dust and particulates from the air through a filter that first captures and separates the matter, and then discharges purified air back into the workplace or environment. Specifications: Fan Speed: 700 RPM to 3000 RPM Available in various sizes 0.25 hp to 150 hp Air handling capacities of 100 CFM to 100000 CFM System resistance of 25mm to 2500mm WG static pressure
Vayuvents manufactures a complete range of high performance scrubbers that are used for removing undesirable acid fumes, chemical substances or odours from the gas stream. Fume scrubbers manufactured by Vayuvents are individually designed to remove mist, entrained liquid particles, noxious corrosive gases and vapours from the exhaust air stream. A packed bed using Vayuvents Scrubber Packers is the heart of the scrubber. Pollutant gases can generally be removed to any desired concentrations to meet local air pollution regulations. The pollutants are removed by means of: Gas Absorption: Noxious or otherwise undesirable gases are absorbed into the liquid phase. Impingement: Particulate matter is removed through impingement as it is first forced through a wetted packed bed and then through a chevron blade or mesh pad filter section. Specifications: MOC: PVC, PP, PVC+FRP, PP+FRP, SS-316, SS-304, MS Available in various sizes 0.25 hp to 150 hp Capacities of 100 CFM to 100000 CFM System resistance of 25mm to 2500mm WG static pressure
We are the dominant manufacturer and supplier a wide array of Kitchen Dry Scrubber. The offered product is produced working with the highest quality raw material and state-of-the-art technology in acquiescence with the international quality standards. Dry Scrubber used in filtration/ cleaning of kitchen exhaust air. The product is useful for restaurants, hotels, office canteens, cafeteria, and club canteens. Specifications: Particle capture range: 0.01m to 10 m Available in various sizes 1 cell to 4 cell Air handling capacities of 1500 CFM to 8000 CFM Product length: 720 mm to 2410 mm
Venturis can be used to collect both particulate and gaseous pollutants, but although the liquid surface area provided is quite large they are more effective in removing particles since particles can be trapped by contact, but gases must be trapped by absorption during the relatively short exposure time. Specifications: MOC: PVC, PP, PVC+FRP, PP+FRP, SS-316, SS-304, MS Available in various sizes 0.25 hp to 150 hp Capacities of 100 CFM to 100000 CFM System resistance of 25mm to 2500mm WG static pressure
The ducting is made from galvanized sheet metal. The duct is made up of a spiral pipe or material configuration. Ducts are conduits or passages used in heating, ventilation, and air conditioning (HVAC) to deliver and remove air. The needed airflows include for example, supply air, return air, and exhaust air. Ducts commonly also deliver ventilation air as part of the supply air. As such, air ducts are one method of ensuring acceptable indoor air quality as well as thermal comfort. A duct system is also called ductwork. Planning (laying out), sizing, optimizing, detailing, and finding the pressure losses through a duct system is called duct design. Specifications: MOC: Galvanized IronAvailable in 2 gauges, 22 gauges to 24 gauges Length as per clients requirements and preferences System resistance of 25mm to 2500mm WG static pressure
We are engaged in manufacturing and exporting a matchless range of Hot Air Blowers to the prestigious customers. These blowers are presented in different capacities and are being offered at the best rates in the market. Further, it is highly acclaimed in the market for its durability and UN-interrupted performance. Specifications: Temp. Rise up-to 150 degree Celsius Customized as per customers requirements. Comes with automatic control panel for 100% Safety
