Technical sheet Biga’ pick-up: Dimensions: Total Length mm 1541 Width mm. 740 Height mm. 1120 Worktop length mm 95 Width mm. 740 Height from the ground mm. 310 Weight: Total including batteries and banks kg.156 Set 3 banks kg. 4 Batteries kg. 27,5 each x 2 Gear Motor: Permanent magnet engine R.R. 10/1 800 W – rpm 330 – 24 V. Voltage and battery: N. 2 batteries capacity 12V 140 A C20 hermetic gel– connected in series, no maintenance. External battery charger 24 v – 12 amp – electronic microprocessor control- Power 220 v. Differential and transmission: Differential, maximum torque of torsion 2 Kgm - 2 Semiaxis with graft at 6 caves Type 13: transmission chain, Sprocket 13 teeth, Crown wheel 45 teeth, Ratio 1/3,47 Type 19. transmission chain, Sprocket 19 teeth, Crown wheel a 45 teeth, Ratio 1/2,37 Type 23: transmission chain, Sprocket 23 teeth, Crown wheel 45 teeth, Ratio 1/2,00 Type 28: transmission chain, Sprocket 28 teeth, Crown wheel 45 teeth, Ratio 1/1,61 Type 34: transmission chain, Sprocket 34 teeth, Crown wheel 45 teeth, Ratio 1/1,33 Brakes: Front drum brake, activation with right hand Back drum brake, activation with left hand Service brake, activation on left lever. Braking increase by the release of the accelerator (engine brake) enhanced in the setting of the parameters of the junction box. Speed and capacity: Towing besides the driver (performance with the vehicle in perfect efficiency) on flat road. The maximum capacity is considered with uniformly distributed load on the worktop and the center of gravity of the goods must not exceed the height of mm. 350 Type 13 max 5 Km/h +/- 10% P/T 800 kg. on the plane P/T 100 Kg. on slopes 15% Type 19 max 6,5 Km/h +/- 10% P/T 600 kg. on the plane Type 23 max 8,5 Km/h +/- 10% P/T 450 kg. on the plane Type 28 max 10,5 Km/h +/- 10% P/T 300 kg. on the plane Type 34 max 12 Km/h +/- 10% P/T 200 kg. on the plane Tires: Covering: 3.00-4 superelastic rubber Structure: Tubular and sheet Fe 37 polyester powder painted for outdoor use Ral 9007 Lights and Devices: signaling and illumination main headlight and tail lights reverse buzzer, horn.
Electric small tower tractor. SPECIFICATIONS: Biga 'Pick-up versions and performance with the vehicle in perfect working on flat surface. type 13 max 5 Km / h + / - 10% P / T 800 kg. on the P / T 100 Kg on slope 15% Type 19 max 6,5 Km / h + / - 10% P / T 600 kg. Type 28 up to 8 Km / h + / - 10% P / T 400 kg. Type 34 up to 11 Km / h + / - 10% P / T 200 kg. The maximum range is considered with the load evenly distributed on the plane and the center of gravity of the goods must not exceed the height of mm. 350. Dimensions: Total Length mm 1540 Width mm. 740 Height mm. 1130 Floor Length mm 940 Width mm. Ground Clearance 740 mm. 310 Weights: Total including batteries and banks kg. 176th September 3 banks kg. Batteries kg. 36 each. x 2 Motor: permanent magnet motor RR 10/1 800 W - rpm from 330 to 24 V. N. 2 batteries 12V 140 A sealed gel - connected in series, without maintenance. External charger 24 v - 12 amp - electronic microprocessor - 220 v. transmission: Differential, max. 2 Kgm torque - 2 Shaft with graft rejection in 6 slot. chain drive with front and rear sprocket. Brakes: Front drum, drive with your right hand. Rear disk drive with his left hand. brake, drive on left lever. increased by releasing the brake (engine brake) enhanced in the calibration of the parameters of the controller. Covers: 3.00-4 rubber tires Frame: Tubular steel and Fe 37 powder-coated polyester for outdoor Ral 9007. lighting and signaling devices : Headlight main and tail lights - reverse buzzer, horn. phonometric values: values ??LpAm max = 77.6 - 85.6 LWA - Attendant Leq dB (A) 77.6 Vibration value: vmax (i) = 0.47 m / s2 (maximum value for operator sitting in the driver's seat). Spare parts and tools for the maintenance and repair: Original spare parts and tools for maintenance and repair are provided directly to order from Italy Bigà spa.
Electric handling kit 1.500/2.000 kg autonomy 5 hours in continuous Functions Stop and Go forward / backward industrial radio remote control flashing and buzzer always on at cart on Speed 4 km / h SPECIFICATIONS: Dimensions: Shopping cart Weight: Your cart + kg. 120 motor 24 V - 600 W - 85 rpm with brake assist, with manual release N. 2 Batteries GEL - 12 V Capacity: 140 Ah C20 - 105 Ah C5 Charger HF 24V - 12 A - 220 V Electronic control technology MOSFET 24 W - 140A ignition key battery charge indicator Emergency button mushroom ex-battery flashing E24 xenon Horn Operating N. 2 6-ply tires 300-4 with inner tubes and aluminum wheels on request: A) lever 2 speed '4/6 km / h B) electric motor brake release lever TECHNICAL RADIO CE: with battery charger Protection transmitter / receiver: IP67 Operating temperature -20 / + 55 ° C Range 150 m. Operating Frequency ISM band: 868.0125 to 869.9878 MHz in Stop category 1 Technology LBT Range at 20 ° C: about 50 hours. transmitting apparatus: AT MYTH - MINI receiving apparatus: AR MYTH - MINI R & TTE Directive 99/05 / EC EMC Directive 2004/108/EC Low Voltage Directive 2006/95/EC Applicable standards EN 300 220 EN 301489-3 EN 61000-6 EN 60529
Small electric tractor for garbage collection and disposal.
Drum melters models dm 200 and dm 20 to process any kind of hot melts – even pur and uv curable – further to a wide range of butyls, glues and polymers with working temperatures up to 240°c in 200 lt- (or 55 gallons) and 20 lt- (or 5 gallons) tanks. Equipped with high precision gear pumps, the system ensures top precision in all conditions of use, both for continuous and intermittent applications. The special design and high-tech materials enable an excellent anti-sticky control and avoid any adhesive deterioration, particularly while using pur adhesives.
The wide range of continuous output melting units model mitsu enables to process any kind of hot melt adhesives in blocks or chips with working temperatures up to 240°c, including reactive pur and uv-curable ones. The melting rate varies from 2.5 to 160 kg/h, according to different models, giving an appropriate answer to all high, medium and low melting requirements. This modular system enables to conform to different production needs thanks to partial use function and possibility to integrate later on the melting capacity.
Automatic adhesive application guns for spray/spiro and glue lines/dots applications. The system processes any kind of hot melt adhesive and is available in single or multiple units with working width from 10 up to 6.000 mm. They enable both continuous and intermittent adhesive applications.
These materials are of the highest quality and our delivery is very prompt. We pack in bales, bags, pallets
Non ferrous and ferrous scraps
only one year contract
Extruder omp 105 Diam 40 Vibro screen Cutting head tecnova Change filter Control panel Year of construction 2002.
Year of construction 2000 Electrical fun Vibro screen Cutting head tbs 10 Change filter 115 Engine HP 100.
Year of construction 2003 Electrical fun Vibro screen Cutting head 30 Engine abb hp 450 Silos tecnova Control panel.
Type 70 diam 40 rotation 350 Year of construction 2001 Engine 186 kw Capacity 800- 1000 kg/h 2 new screws Control panel Warranty for 6 months.
Need dosage Cutting head Vibro screen Change filter Year of construction 2010 Hours functioned 300.
Italian Company sells 1K PU-Acrylate glossy/semi-glossy/matt/super matt lacquer, odorless with very low VOC content. It has a high solid content which provide the wood a warm light tone. Suggested for treatment of wooden floors in homes and other areas subject to normal wear. Fully compliant with VOC 2010 legislation.
Italian company sells 2k water-based pu glossy/semi-glossy/matt/super matt lacquer, odorless with very low voc content. It has a high solid content and provides the wood a warm light tone. Suggested for treatment of wooden floors in commercial premises or wherever a high resistance to wear is required. Total resistance to the ôblack heel markö.
Italian company sells two-component polyurethane varnish (1:1). Glossy, elastic, hard-wearing and scratch-resistant. Particularly recommended for varnishing traditional parquet of all wood types. Resistant to washing with water and neutral detergents. Duro lack mc 50 gives an even finish.
Italian company sells single-component oil-based urethane glossy/semi-glossy/matt/super matt/coloured finish for varnishing wooden floors. Excellent surface finish with waxed/oiled effect. Ideal for flamed woods.
Linen embossed paper for wrapped boxes, files, folders, cover, gift card, gift box All size
