Aluminum scrap
It is assumed pick-up will be performed with: - Transported material: powder or fluent plastic granules; - Apparent specific weight 0.7 kg/dm³; - Initial pick-up length having inclination α = 0° and α = 30°; - Rotary spiral with 580 rpm (930 rpm applications are also possible). Load capacity from 120 kg/h-10,000 kg/h.
LPG conversion system.
Auto gas conversion system.
LPG conversion system.
LPG conversion system .
LPG conversion system.
Fasteners Engine foundation bolts Axles for motor cycles Fuel pumps Spool devices for tractor fuel pumps Sub assemblies
Plastic dustpan Material PP 32 cm x 23 cm x 5 cm
EC FERTILIZER Magnesium sulphate COMPOSITION - Magnesium oxide (MgO) soluble in water 16% - Sulfur dioxide (SO3) soluble in water 32%
Edible oils, chemicals, minerals.
Made in italy water filters, filter housings and filter cartridges.Manufacturer
: Tyre bladders scrap, tyre bead wire, tyre side walls, used nylon conveyor belts, used electric motors, used fridge and air condition compressors, insulated copper wire, used rediator scrap, PVC plastic scrap
Hot-rolled steel channels This type of channel is produced according to GOST 535-88 with parallel flanges and sloping flanges: 10, 10P and etc. The slope of inner flanges must not exceed 10%. Assortment of the steel hot-rolled channel corresponds to GOST 8240-89. The number of the channel corresponds to its size (distance between the inner flanges) expressed in cm. For example: Channel #10 - distance between the inner flanges equals 10cm. All other parameters: flange width, wall thickness and etc. according to GOST. Channel that has letter A at the end of the number (14A) is a channel with sloping inner flanges, it means the flanges are wider and hence the weight of each meter is larger than ordinary channel. There are special types of hot-rolled channel: special channel for automotive industry - GOST 19425-74 (18S, 20S); special channel for wagon production - GOST 5267.1-90 (8W, 14W, 18W).
I-BEAM- double flanged - this type of products include hot rolled double flanged beams (I-beams), produced according to GOST 535-88. I-Beams are separated into several types: I-Beams with parallel flanges normal (20B, and etc.) wide flanges (20Sh and etc.) column (20K and etc.) I-Beams with sloping edges of flanges normal (edge slope 6-12%) GOST 8239-89 (â??10, 12, 16 and etc.) Assortment of such I-Beams corresponds to GOST 8239-89. Special (M and C): M - for hanging rails (edge slope not more than 12%): 18M, 24M, 30M and etc.; C - for reinforcement of mine shafts (edge slope not more than 16%): 14S, 20S and etc. Assortment of such double flanged beams corresponds to GOST 19425-74. The number of the I-beam is its conventional size (height) in cm.
Assortment corresponds to GOST 8509-93. Precision classes: A - high precision; B - ordinary precision. The number of equal flange steel corresponds to flange width, expressed in mm. For example: Angle 25 -flange width 25mm. All other sizes (wall thickness and etc.) according to GOST (shown in the table of GOST book of reference).
Hot-rolled flat bar - the most sought-after type of strip. Distinguish rolled dimensional (length 0.6 and 1.2 m), a multiple of the measured length and unmeasured (length 0.2 - 0.6 m). At the same time, a bar with a thickness of up to 4.5 mm is produced with a width of all sizes provided for by GOST. In accordance with GOST 103-76, the size of this product may vary in the range:length - 2-10m; width - 20 200 mm;thickness - 4 - 40 mm.
The material of manufacture and the range of the round bar in accordance with GOST 2590-2006, where the bar can be made of steel of the following grades: carbon (St3, St20, St35, St45); low alloyed (Steel 40X, Steel 40XH); high-alloyed (08 18 10, 38XH3MA, 40 2 14 17 2 and others), high-speed (U7; U7A; U8A)
Steel square can be made of steel of various grades: carbon - St3, St20, St35; St45 low alloyed - Steel 40X, Steel 40XH; high-alloyed - 08 18 10; 40XH2MA; 38XH3MA; 14 17�?2 and others high-speed - U7; U7A; U8A
Thermally strengthened periodically profiled steel rods of the diameter 6-40mm - the so called thermic is used for the construction of strategic reinforced concrete structures, GOST 10884-81. According to the standard this rebar is made out of these types of steel: AtIII - St (sp, ps); AtIV, AtIVK - 20GS, 25G2S, 35GS, 28S, 10GS2, 08G2S, 25S2P; AtV(K and SK) - 20GS, 20GS2, 08G2S, 10GS2, 28S, 25G2S, 35GS, 25S2R, 20HGS2; AtVII - 30HS2.
