The benefits of ptek rchf3 Ripple, it also integrate the input and output protections and Is equipped with an over-temperature control both on the Primary side and the secondary side of the converter. With a wholly programmable control unit, easy-to-use with the User-friendly graphic interface displaying all the parameters, Historical data of the charge cycles executed, alarms, data Plate and all general information concerning the device. The interface also allows setting all the charge parameters, Selecting the charge curves, setting the clock and activating all The optional functions. Ptek rchf is equipped with a monochromatic graphic lcd Display of 64x128 pixels. The control unit can be connect it to a personal computer. An interface software for pc is available permitting a whole Configuration of the ptek rchf, in order to check and monitor All the functions in real time. The software is equipped With a specific tool for the charge curve configuration and Customization. Input voltage: 400 vca ± 15% three-phase, input frequency: 50 – 60 hz, Efficiency: ~ 90%, operating temperature: – 20 to + 50 °c, current drawn by the Battery: 0 a, if network electrically bonded, protection against output short-circuit, Protection against polarity reversal, thermal protection semi-conductors, input Protection, charge curve: programming and settings, displaying and messages with Monochromatic graphic lcd display, thermal compensation with optional probe, Ventilation with forced air circulation, metallic body with these dimensions: 830 x 500 x 500 mm, protection ip20, in conformity with the low voltage directive 73/23/ Cee and the emc and directive 89/336/cee and their successive amendments.
Attery charger due to battery Disconnection, smart charging system according to the discharge level of the battery, Short check of functions and times, option: custom-made colour and custom-made Logo and silk-screen printing, final acceptance test conforming to safety regulations, Charging with decreasing current (wa characteristic): 9÷11 h charging time, charging With decreasing current (wo - wa characteristic): 7÷8 h charging time, complete With mains and battery cables; assembly of plugs and battery connectors on request. Wa (din 41774): Charge at decreasing current with intervention of the Final charge at 2.40 v/cell, final charge with timed Control 9h / 11h, fixed charging time (equalization Charge excluded), equalization charge (week-end Charge) to be recalled. It will start after 55’ from Charge end, duration of equalized charging phase: Each hour 5’ (repeated for 48 hours), calculation to Determine the size of suitable battery charge: 16a For every 100 ah of the battery (e.G. 500 ah battery: 16ax5 = 80a). Wo-wa: Charge at decreasing current with intervention of the Final charge at 2.42 v/cell, final charge with timed Control 7h / 8h, fixed charging time (equalization Charge excluded), equalization charge (week-end
ier output, rectifier bridge with snubber protection, short check of functions and times, option to program the equalized charge automatically, lab tested electronic circuit conforming to the directive on electromagnetic compatibility and CE marking, automatic Start, automatic disconnection of battery charger due to battery disconnection, equalization charge based on time, charging with decreasing current (Wa characteristic): 9÷11 h charging time, transformer thermal protection, modular installation on galvanized steel base (20/10) – (30/10), sheet steel case with modular panels (10/10 - 12/10) - (12/10 – 15/10), epoxy powder coating, oven-baked, standard colour: RAL 2002 red, option: custom-made colour, logo and silk-screen printing, mains input and d.c. output polarized cables, complete with mains and battery cables; assembly of plugs and battery connectors on request. “WA” CHARACTERISTIC (DIN 41774): charge at decreasing current with intervention of the final charge at 2.40 V/cell., final charge with timed control 9h / 11h, fixed charging time (equalization charge excluded), equalization charge (week-end charge) to be recalled. It will start after 55’ from charge end, duration of equalized charging phase: each hour 5’ (repeated for 48 hours), calculation to determine the size of suitable battery charge: 16A for every 100 Ah of the battery (e.g. 500 Ah battery: 16Ax5 = 80A).
The battery chargers of the cemb-easy 3000 Series are designed to recharge medium capacity Traction and start lead-acid batteries and are O the directive on electomagnetic Compatibility and ce marking. • option: custom-made colour • custom-made logo and silk-screen printing • complete with mains and battery cables; assembly of plugs and battery connectors On request. Technical characteristics easy 3000: • 230v - 50hz one phase supply, (with possibility to request voltages different from The standard ones), adjustable to ± 5% or ± 10% • electronic control provided with final charge timer • on-off switch • rectifier bridge with silicon diodes, natural cooling, with snubber protection and Gemov • tropicalized stray-flux transformer : tenvex copper windings with double enamel Insulation; class h; impregnated in autoclave with ecological epoxy resins. • 12/10 sheet steel case provided with electrical bondings and ergonomic handle • epoxy powder coating, oven-baked • standard colour: ral2002 red • new lexan plate with charging data very easy to understand • lab-tested electronic circuit conforming to the directive on electomagnetic Compatibility and ce marking. • option: custom-made colour • custom-made logo and silk-screen printing • complete with mains and battery cables; assembly of plugs and battery connectors On request. • charge at decreasing current with intervention of the final charge At 2.40 v/cell • final charge with timed control 9h / 11h • fixed charging time (equalization charge excluded) • equalization charge (week-end charge) to be recalled. It will start after 55’ from Charge end • duration of equalized charging phase: each hour 5’ (repeated for 48 hours) • calculation to determine the size of suitable battery charge: 16a for every 100 Ah of the battery (e.G. 500 ah battery: 16ax5 = 80a)
Asuring via digital Gearcase. Such microprocessor control is designed to optimize the Charging cycles for any type of battery. • 230v coil three-pole contactor. • d.C. Fuse on rectifier output. • delta-star stray flux three-phase power transformer class h; Impregnated in autoclave with ecological epoxy resins, with Thermocouples for disconnection due to maximum temperature. • three-phase rectifier bridge with silicon diodes, natural cooling, with
Charge end, duration of equalized charging phase: Each hour 5’ (repeated for 48 hours), calculation to Determine the size of suitable battery charge: 16a For every 100 ah of the battery (e.G. 500 ah battery: 16ax5 = 80a).
With decreasing Current (wa characteristic): 9÷11 h charging time, transformer thermal protection, Modular installation on galvanized steel base (20/10) – (30/10), sheet steel case With modular panels (10/10 - 12/10) - (12/10 – 15/10), epoxy powder coating, ovenbaked, Standard colour: ral 2002 red, option: custom-made colour, logo and silkscreen Printing, mains input and d.C. Output polarized cables, complete with mains And battery cables; assembly of plugs and battery connectors on request. “wa” characteristic (din 41774): Charge at decreasing current with intervention of the final charge at 2.40 v/cell., final charge with timed control 9h / 11h, fixed charging Time (equalization charge excluded), equalization charge (week-end Charge) to be recalled. It will start after 55’ from charge end, duration Of equalized charging phase: each hour 5’ (repeated for 48 hours), Calculation to determine the size of suitable battery charge: 16a for Every 100 ah of the battery (e.G. 500 ah battery: 16ax5 = 80a).
Switching technology with microcontroller digital control. They Are flexible and reliable devices. The high efficiency of the battery Chargers assures a remarkable energy saving optimizing the Economic benefits and permitting to amortize the investment for The selection of high frequency in a short time. They are suitable for the recharge of all kind of batteries (leadacid Gel, sealed, agm batteries, etc…) and allow selecting a specific Charge curve or configuring easily a suitable curve for the type of Battery. They are characterized by a negligible residual output ripple. The battery chargers integrate the input and output protections And are equipped with an over-temperature. They have a wholly programmable control unit, easy-to-use thanks To the user-friendly graphic interface displaying all the charge Parameters, the alarms, the data plate and all general information Concerning the device. These kind of battery chargers are equipped With a monochromatic graphic lcd display/led. Technical characteristics: - input voltage: 230 vca ± 10%, mono-phase - input frequency: 50 – 60 hz - efficiency: ~ 90% - operating temperature: – 20 to + 45 °c - current drawn by the battery: 0 a, if network electrically Bonded - protection against output short-circuit: yes, fuse - protection against polarity reversal: yes, fuse - thermal protection semi-conductors: yes - input protection: yes, fuses and varistors - charge curve: programming and settings at Will - default iu ia - displaying and messages: monochromatic 2x20 lcd Display - led - audible alarm device: yes - state charge indicator: yes multicolours
Solar street lights to be fit easly in every place, also without the electricity facility. CE certified. For any information please don't hesitate to contact us.
Features: Intelligent electricity saver up to -35%. A new technology in power saving! Proven to save within first month! Easy to use, just plug in and start saving ! Saving up to 35% of your bill ! Product feature: Reduce your electricity bill up to -35% Improve electrical efficiency and power factor Reduce power loss Prolong the life of appliances Easy to use. Maintenance free. Fully compliant with safety standards Reduce electrical overheating Stabilize the supply voltage Environmental friendly Aesthetic design.
Customized robot cells Full-comprehensive productive solutions with high-reliability components and units, carefully selected and checked for quality over more than 20 years extremely positive experience . Regular wodden crates, suitable to be included in container for oversea shipments
Industrial washing machine
Grinders.
Pendants, glasses, candle handers, glass recipients, glass flowers.Shipping
Stocklot composed of cables, audio accessories, video, mobile telephony, tablets, IT Total pieces 290,000 (all in blister) 10 containers of 40 feet Packing list available on request Price FOB
Casting and steel manifolds connect exhaust output from engine head to exhaust pipe channelling the exhaust gases towards the emissions reduction and silencing systems. We manufacture our products with the highest quality and certified types of cast iron and steel to guarantee the best performance in heat resistance and thermal stock. Our latest range extension is for turbocharger applications that require top quality materials and machining. We provide our quality products complete with fitting kit to guarantee the proper assembly and an excellent performance of the exhaust system. Catalysts design is specific for each application and all our maniverters are ECE 103R type-approved according to European emissions standards and regulations.
Centrifugal Fan.
Industrial spare parts for pneumatic, electrical, hydraulic, mechanical fields for example pumps, motors, valves .Export
Indoor lighting products.
Geyser heater, water heater, coil nozzle heater, tubular heater, cartridge heater, furnace heater, ladle heater, mould heater, ceramics heater and immersion heater.
