Tobee G/GH Sand Gravel Pumps are designed specifically for continuous pumping of extremely aggressive slurries, gavels, and sands. with a wide particle size distribution. Capable of handling large particles at consistently high efficiencies results in low cost of ownership. The large volume internal profile of the casing reduces associated velocities further increasing component life. Design Features: The unique segmented clamp ring on larger size units and solid on smaller pumps, facilitates casing rotation to any angle, reducing the need for costly high wearing bends. Minimal maintenance is required. Impeller expulsion vanes reduce gland pressure and intrusion of high concentrations of solids in the gland area. Efficiency is maintained by minimising suction side recirculation.
Tobee 250TV-SP Vertical Slurry Pump is no submerged bearings or seals heavy duty cantilevered pumps, which ideal for a variety of submerged suction pumping applications. These pumps operate well in a variety of sump conditions, and can also be readily applied on floating dewatering or other floating pump platforms. Design Features: Bearing Assembly - The bearings, shaft and housing are generously proportioned to avoid problems associated with the operation of cantilevered shafts in the first critical speed zones. The assembly is grease lubricated and sealed by labyrinths; the upper is grease purged and the lower protected by a special flinger. The upper or drive end bearing is a parallel roller type whilst the lower bearing is a double taper roller with preset end float. This high performance bearing arrangement and robust shaft eliminates the need for a lower submerged bearing. Column Assembly - Completely fabricated from mild steel. The SPR model is elastomer covered. Casing - Has a simple bolt-on attachment to the base of the column. It is manufactured from a wear resistant alloy for the SP and from moulded elastomer for the SPR.
Tobee 300TV-SP Vertical Slurry Pump is designed to be immersed in liquid for conveying abrasive, coarse particles, dirty water and particle contaminated water. Due to the design of the pump assembly, a shaft seal is not required and the pump can be operated in conditions that most pumps would have a low service life and their seal arrangement would not be effective. Design Features: Fully Cantilevered - Eliminates submerged bearings, packing, lip seals, and mechanical seals that other vertical slurry pumps typically require. Impellers - Unique double suction impellers; fluid flow enters the top as well as the bottom. This design eliminates shaft seals and reduces thrust load on the bearings. Large Particle - Large particle impellers are also available and enable passing unusually large solids. Bearing Assembly - The maintenance friendly bearing assembly has heavy duty roller bearings, robust housings, and a massive shaft. Casing - The metal pumps have a heavy walled abrasive resistant Cr27Mo chrome alloy casing. Rubber pumps have a molded rubber casing adhered to sturdy metal structures. Column and Discharge Pipe - The metal pump columns and discharge pipes are steel, and the rubber columns and discharge pipes are rubber covered.
Tobee SPR Rubber Lined Vertical Slurry Pumps are available in various standard lengths to suit common sump depths, for very deep sumps or where high shaft speeds limit the length of the pump, a suction extension pipe can be fitted to the bottom inlet to extend the depth of the pump by up to 2 meters. Pumping is maintained even when the top inlet is not submerged, thus enabling the level of liquid to be lowered right down to the bottom inlet or the bottom of any suction extension pipe. The wet parts of SPR vertical sump pump is interchangeable with the SP series hard metal lined heavy duty sump pumps. Design Features: Bearing Assembly - The bearings, shaft and housing are generously proportioned to avoid problems associated with the operation of cantilevered shafts in the first critical speed zones. The assembly is grease lubricated and sealed by labyrinths; the upper is grease purged and the lower protected by a special flinger. The upper or drive end bearing is a parallel roller type whilst the lower bearing is a double taper roller with preset end float. This high performance bearing arrangement and robust shaft eliminates the need for a lower submerged bearing. Column Assembly - Completely fabricated from mild steel. The SPR model is elastomer covered. Casing - Has a simple bolt-on attachment to the base of the column. It is manufactured from a wear resistant alloy for the SP and from moulded elastomer for the SPR.
Tobee SP/SPR vertical slurry pump is designed for applications requiring greater reliability and durability than conventional vertical process pumps can offer. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Customized submerged length and suction agitator available. The SP/SPR vertical sump pump ideally suited for heavy continuous handling of abrasive and corrosive liquids and slurries whilst submerged in sumps or pits. Design Features: Less wear, less corrosion Wetted components are available in a wide range of alloys and elastomers, from which Weir Minerals selects the optimum combination of materials for maximum resistance to wear in virtually any industrial application, including those demanding both abrasion and corrosion resistance and where larger particles or high density slurries are encountered.
Tobee SP/SPR vertical slurry pump is designed for applications requiring greater reliability and durability than conventional vertical process pumps can offer. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Customized submerged length and suction agitator available. The SP/SPR vertical sump pump ideally suited for heavy continuous handling of abrasive and corrosive liquids and slurries whilst submerged in sumps or pits. Design Features: Less wear, less corrosion Wetted components are available in a wide range of alloys and elastomers, from which Weir Minerals selects the optimum combination of materials for maximum resistance to wear in virtually any industrial application, including those demanding both abrasion and corrosion resistance and where larger particles or high density slurries are encountered.
Tobee M Medium Slurry Pumps are designed for continuous pumping of medium duty abrasive/dense slurries in processes from minerals processing, cyclone feed to regrind, flotation and tailings. Design Features: Modular design for ease of maintenance. Medium duty one piece frame base with lifting points for easy maintenance. Standard ductile iron outer casings for higher working pressures and incorporating lifting points. Standard or advanced bearing assembly improves reliability to extend bearing life reduce lubrication costs. Shaft sealing for increased reliability, stuffing box, expeller, elevated seal or mechanical seal options available. Standard or advanced impeller design options available. Allows ease of fitting multiple liner materials, including hard metal, thick section rubber or polyurethane. Single piece sleeve for stuffing box sealing, lowers stock holding and maintenance. Multi-purpose design allows for reduced inventory requirements and interchangeability. Belt guards allows for ease of maintenance and inspection of belt condition.
Tobee L Light Duty Slurry Pumps have been developed for continuous use in slurry applications where low to medium developed head is required, designed for lighter slurry densities up to 1,35. Shares proven unique design features with the AH slurry pump range, A key feature is the light duty high efficiency impeller, engineered with the latest hydraulic and wear technologies for high efficiency and increased wear life. With a range of high quality parts and different material combinations the L Light duty slurry pump has the versatility to ensure the most appropriate pumping solution provided for any given application. Design Features: Heavy duty construction with through-bolt design provides ease of maintenance and minimal downtime. Ductile iron fully lined casing provides durability, strength, safety, and long service life. Large diameter, slow turning, high efficiency impellers designed to achieve maximum wear life and low operating costs. Large, open internal passages designed to reduce internal velocities, maximize wear life and lower operating costs. Thick elastomer or alloy bolt-in liners provide superior corrosion resistance plus offer ease of liner change-out and interchangeability to reduce overall maintenance costs and maximize wear life. Designed for rugged duties while offering excellent efficiencies.
Tobee DT Series FGD Gypsum Slurry Pump is a single stage, single suction horizontal centrifugal pump. Mainly used as the circulating pump for absorbent tower in FGD system. It has the advantages of wide range capacity, high efficiency, better energy saving etc,The wetted parts are designed with the CFD fluid simulating analysis technology to ensure its high-efficiency operation. DT series FGD slurry pump is optimal pump type for transporting gypsum slurry, limestone slurry or other abrasive and corrosive medium in thermal power plants. Design Features: DT series FGD slurry pump wetted parts adopt the advanced flow simulation technology to guarantee reliable design and high operating efficiency. Corrosion resistant and wear resistant metal and rubber materials for options. The special integrated mechanical seal design is suitable to Thermal Power Plant Fuel Gas Desulphurization process. The bearing at pump end is double-row taper roller bearing, and bearing at drive end is cylindrical roller bearing. The bearings are lubricated with oil to longer the service time. Achieve highest efficiency all the time by adjusting the bearing components to alter the impeller position in pump chamber. The pump can be disassembled without dismantling suction or discharge pipes.
Tobee TL(R) FGD Limestone Slurry Pump is the new generation high efficiency energy saving pump product elaborately researched and developed by Tobee through absorbing the technical advantages from similar FGD pumps from domestic and abroad, with reference to the technical specifications of flue gas desulfurization project, aiming at the characteristic of FGD system of transporting medium through pump in thermal power plant. Design Features: Excellent performance and comparatively high reliability and stability. Simple structure, convenient maintenance and reliable operation. Excellent performance of corrosion resisting and wear resisting, suitable for transporting different PH medium. The bearing body adopts tubular structure, which will adjust the bearing parts to change the position of impeller in the pump cavity and make the pump be always under high efficiency operating status. The shaft seals can be classified as filler seal, dynamic seal and assembled mechanical seal specially used for desulphurization technology to facilitate users to select suitable shaft seal according to actual condition. It is easy to be installed and maintained without connecting clean industrial flushing water.
Tobee 6x4D-AH Slurry Pump is a single-stage, single-suction and horizontal heavy duty centrifugal slurry pump with a cantilever design, The 6x4 slury pumps are mainly used in solids containing applications. Depending on process conditions, equipment should be suitable for highly abrasive or corrosive liquids. Design Features: Cylindrical structure of bearing assembly: convenient to adjust the space between impeller and front liner and can be removed completely. Interchangeable anti-abrasive wet parts made of high-chrome alloys. The discharge branch can be oriented to any eight positions at the interval of 45 degrees. Various drive types: DC (direct connection), V-belt drive, gear box reducer, hydraulic couplings, VFD, SCR control etc. The shaft seal uses the packing seal, expeller seal and mechanical seal.
Tobee 14x12ST-AH Slurry Pump is made for high wearing and heavy duty applications. 14x12 slurry pumps and replacement parts are used worldwide industries like mining, mineral processing, power generation, aggregate processing, or any type of slurry pumping system. It is especially for handling the toughest and most abrasive applications. Design Features: Power End Labyrinth bearing isolators to protect internal components during wash-down cycles. Clearances can be easily adjusted to maintain efficiency while optimizing performance and extending wear life. Over-sized, self-aligning spherical roller bearings for trouble free operation. Heavy duty bearing assembly, 50,000 hour minimum L10 bearing life, Distortion free bearing clamp system ensures maximum bearing life and prevents premature fatigue.
S/SH series is suitable for transporting pure water or other liquids of both physical and chemical natures similar to pure water. It is applicable to transport medium with temperature of not higher than 80â?? , and high temperature boiler water or transporting medium similar to hot water. If The TDG pumps add a cooling system with specfice shaft seal and materials, It can be used to transport boiler water, hot water, oil, chemicals or corrosive liquids with the temperature of not higher than 130.
Tobe 16x14TU-AH Slurry Pumps provide a ideal replacement for many OEM slurry pumps used in Minerals processing plant, such as Mill Discharge, cyclone feed, transfer slurry tailing, dewatering, pipeline, Power plant, Chemical Process, sand and gravel process, and any other industry application need to transport heavy duty abrasive and corrosion medium. Design Features: Heavy duty construction with through-bolt design provides ease of maintenance and minimal downtime Ductile iron fully lined casing provides durability, strength, safety, and long service life Large diameter, slow turning, high efficiency slurry pump impellers designed to achieve maximum wear life and low operating costs Large, open internal passages designed to reduce internal velocities, maximise wear life and lower operating costs Thick elastomer or alloy bolt-in liners provide superior corrosion resistance plus offer ease of liner change-out and interchangeability to reduce overall maintenance costs and maximise wear life Minimal shaft/impeller overhang reduces shaft deflection and increases packing life Cartridge-style bearing assembly allows for maintenance in a clean environment without removal of the slurry pump, resulting in reliable operation and prolonged bearing life
Tobee 4/3E-HH High Head Slurry Pump is fit for a variety of applications ranging from filter press feeds to pipeline transport staging pumps. The high heads along with sturdier wear parts makes these pumps some of the most rugged in the slurry pump line. Extensive exterior ribbing allows for higher heads to be reached with a single slurry pump, and bulked up wet end parts handle the toughest applications in the field today. Design Features: Ductile iron fully lined casing provides durability, strength and long service life. Multi-stage high pressure operation to 750 psi. Heavy duty construction with through-bolt design provides ease of maintenance and minimal downtime. Large diameter, slow turning, high efficiency impellers designed to achieve maximum wear life and low operating costs. Large, open internal passages designed to maximize wear life and lower operating costs. Thick elastomer and alloy liners provide superior corrosion resistance and maximum wear life. Full flush gland, low flow, and dry running centrifugal seals reduce flush water usage minimizing pump operating costs.
Slurry Pumps are the most comprehensive range of centrifugal slurry pumps for use in mining, minerals processing, coal preparation, dredging, metallurgy, power plant, chemical and general industry applications. The wetted parts materials designed by High abrasion and corrosion resistance alloy, rubber or polyurethane etc, Expecially for handling high abrasive, high density slurries. Design Features Bearing assembly - a large diameter shaft with short overhang minimizes deflection and contributes to long bearing life. Only four through bolts are required to hold the cartridge type housing in the frame. Volute Liners - easily replaceable liners are bolted, not glued, to the casing for positive attachment and east of maintenance. Hard metal liners are completely interchangeable with pressure moulded elastomer. Elastomer seal rings back all liner joints. Pump casing - Casing halves of cast or ductile iron with external reinforcing ribs provide high operating pressure capabilities and an extra measure of safety. Impeller front and rear shrouds have pump out vanes that reduce recirculation and seal contamination. Hard metal and moulded elastomer impellers are completely interchangeable.
Desulfurization pumps are corrosion-resistant pumps, mainly used for the transportation of corrosive liquids. It is a widely used pump among general equipment pumps. The desulfurization pump is usually a horizontal cantilever single-stage single-suction centrifugal pump, which is specially designed and developed for transporting corrosive media containing fine particles. The flow material of the desulfurization pump is required to be wear-resistant and corrosion-resistant.
Vertical slurry pumps are no submerged bearings or seals cantilevered pumps, which ideal for a variety of submerged suction pumping applications. These pumps operate well in a variety of sump conditions, and can also be readily applied on floating dewatering or other floating pump platforms.
The pumps can be used in many applications, such as Pipeline transport, High velocity hydraulic transport, Mineral processing, Coal prep, Cyclone feeds, Aggregate processing, Fine primary mill grinding, Chemical slurry service, Tailings, secondary grinding, Industrial processing, Pulp and paper, Food processing, Cracking operations, Ash handling.
M/AH/HH SREIES are designed for handling highly abrasive,high density slurries with excellent wear life while maintaining efficiency during the wear cycle providing the best total operating cost.
