300TV-SP Vertical Slurry Pump is designed to be immersed in liquid for conveying abrasive, coarse particles, dirty water and particle contaminated water. Due to the design of the pump assembly, a shaft seal is not required and the pump can be operated in conditions that most pumps would have a low service life and their seal arrangement would not be effective.
TG14x12T Gravel pump is interchangeable with 14/12T-G Pump. It is designed specifically for continuous pumping of extremely aggressive slurries, with a wide particle size distribution. Its wear parts made from high chrome alloy, The hardness can upto HRC65, Capable of handling large particles at consistently high efficiencies results in low cost of ownership. The large volume internal profile of the casing reduces associated velocities further increasing component life. 14/12T-G Gravel Pump Design Features: Bearing assembly - Large diameter shaft with short overhang contributes to long bearing life. Liners - Easily replaceable liners are bolted, not glued to the casing for positive maintenance. Casing - Casing halves of cast or ductile iron provide high operating pressure capabilities. Impeller - Front and rear shrouds have pump out vanes that reduce recirculation and seal contamination. Throat bush - Wear is reduced and maintenance simplified by the use of tapered.
Tobee 12/10 FG River Stone Suction Pump 3 vanes Closed type Impeller FG10137A05 which specially designed and shaped impeller vanes allow the handling of extraordinarily large particles. The unique casing design and sealing vanes prevent abrasive solids intrusion at the sealing faces.
Tobee 6/4D-G Single Casing Sand Gravel Mining Pump with high chrome material and packing seal arrangement that used in river sand. 6x4D-G Gravel Pump is designed specifically for continuous pumping of extremely aggressive slurries, with a wide particle size distribution. Capable of handling large particles at consistently high efficiencies results in low cost of ownership. The large volume internal profile of the casing reduces associated velocities further increasing component life.
Tobee 6/4 AHR Slurry Pumps can make the inlet to 5 inch with an adaptor, that's 5/4 AHR slurry pump with polyurethane lined parts, The main purpose of the 6/4 AHR slurry pump is to move these sands from one place to another without damaging the pump or the surrounding environment. 6/4 Polyurethane Slurry Pumps are directly connection with slurries, It is very crucial to the service life of slurry pumps. The worklife of Polyurethane parts is longer than Rubber materials for 3~5 times, Polyurethane wetted parts include Impeller, Throatbush, Frame plate liner, Cover plate liner, Frame plate liner insert etc. They are very easily worn-out components because they work under longtime impact of abrasive and corrosive slurries. For the long service life of pump parts, Polyurethane material plays an important role here.
Tobee Mission Sandmaster Pumps have compact and adaptable that includes virtually all of the features of theMAGNUM I pumps. Mission centrifugal Sandmaster pumps to suit for all kinds of drilling sand pump application. Bare shaft pumps, matching motors are available from 7.5KW to 90KW, with rotation 800, 1000, 1150,1450, 1750 to 3500 RPM at 50Hz or 60Hz. The model 10x8x14 and 8x6x14 centrifugal sandmaster pump used on solid control system over 3000 meter-long drilling rigs, with big viscosity and heavy specific gravity drilling fluid. 8x6x11 centrifugal mud solid control feeding pump applies to under 3000 meter-long drilling rigs, and it also can be used to supply mud to triplex mud pump as a filling pump. 6x511 centrifugal pump applies to truck-mounted drilling rigs or pocket drilling rigs. 4x3x13 drilling centrifugal pump is usually used as measuring pump or replenishment pump. 3x2x13 model pump is usually used as clean water pump. Mission Sandmaster Pump Designs: Compact heavy-duty frame design for small space; Multiple application in the oil and gas industrial; Full open impeller reduces shaft loading; Replaceable stuffing box cover, Available in hard ductile iron, high chrome alloy fluid ends(casing, impeller, wear pad, stuffing box), customized fluid ends in stainless steel or aluminum bronze acceptable; Available in 8 different size, 3x2, 4x3, 5x4, 6x5, 8x6, 10x8; One-piece concentric and thicker casing with same power end; SKF bearings or equal; Oil or grease lube available; oil lube is for speeds in excess of 2400rpm; 3500rpm is available for 3x2x13 and 4x3x13 pump; Completely interchangeable with Mission Sandmaster and MCM Mud Master and all other popular brand design in the market; Spare parts are interchangeable with the standard model. The pumps can be unitized with hydraulic motors driven.
Tobee SP/SPR vertical slurry pump is designed for applications requiring greater reliability and durability than conventional vertical process pumps can offer. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Customized submerged length and suction agitator available. The SP/SPR vertical sump pump ideally suited for heavy continuous handling of abrasive and corrosive liquids and slurries whilst submerged in sumps or pits.
Slurry pump Volute Liner is an important wetted end parts of slurry pumps ,and slurry pump volute basic part number is 110. It forms a slurry pump chamber with slurry pump throat bush and slurry pump frame plate liner insert where the slurry would flow through them. The main purposes of a volute casing is to help balance the hydraulic pressure on the shaft of the slurry pump. The slurry pump volute has functions as follows: 1) Closed the slurry pump impeller to a certain space, so that inhaled and forced out liquid through the role of the impeller. 2) Most of Pump volute are made to be Volute-shaped, it is also called the slurry pump casing. Because the area of channel section is widening , the high speed liquid around the slurry pump impeller gradually reduce the flow velocity, and part of the kinetic energy is converted to static pressure can effectively 3) The slurry pump volute liner is not only collected liquid that thrown out by the slurry pump impeller, but also an energy conversion device 4) Lead evenly the liquid to the impeller, collect the high-speed flowed liquid from the pump impeller, and send to the next level or export-led. 5) Realize the energy conversion, Reduce the flow speed, transform the kinetic energy to pressure energy . 6) Connect other components, and play a supporting role.
Slurry Pump Bearing Housing is one most important part of bearing assembly for slurry pumps, It contains shaft and bearings, There are four clamp bolts through the base which fasten the slurry pump bearing housing. Tobee�® Slurry Pump Bearing Housing Specifications: Part No.: 004 Materials: Hard Iron, OEM Models: AH, HH, L, M, G, GH, etc Tobee Slurry Pump Bearing Housing description: Bearing Housing with Shaft for Bearing Assembly of Heavy Duty Slurry Pumps. Introduction: Bearing assembly is an assembled part which comprises parts like shaft, bearing housing, bearings, end cover, labyrinth, etc. and is the rotor part of a slurry pump.Heavy duty roller bearings are housed in a removeable bearing cartridge. Cartridge type with grease lubricated roller bearings designed for more than 60 000 operating hours. Slurry pump shaft, slurry pump bearing housing, slurry pump bearings, slurry pump end cover, and slurry pump labyrinth, etc.assembled a slurry pump bearing assembly, and is the rotor parts of slurry pump. The bearings installed are branded, ZWZ, HRB, SKF, TIMKEN.
Tobee is committed to improvement of slurry pump spares continues with the introduction of the Hyperchrome alloy material. Slurry pump spares have direct connection with slurry, are very crucial to the service life of slurry pumps. The slurry pump spare parts include slurry pump impeller, slurry pump liners, slurry pump throatbush, slurry pump frame plate liner insert, slurry pump casing, slurry pump shaft, slurry pump shaft sleeves, slurry pump bearing assembly etc, They are very easily worn-out components because the slurry pump spares work under longtime impact of abrasive and corrosive slurries in the high speed. For the long service life of slurry pump spares, the material plays an important role here.
Slurry Pump Bearing basic part number is 009, its function is to constrain shaft to only rotation in bearing housing., Normally, The slurry pump will use 2~3 rolling bearings, It is lubricated by grease or thin oil, The bearing uses spheres or small cylinders that rotate or roll between a shaft and other mating parts to reduce friction and allow much tighter mechanical tolerances. Tobee offers ZWZ, SKF, TIMKEN, NSK, FAG, NTN brands for different options.
Tobee Labyrinth T062DM-10-E62 is a component of drive end parts installed on slurry pump bearing assembly for 14/12ST-AH Slurry pumps, 14/12T-G Gravel Pumps. its purpose is to plug the hole in the bearing housing where the shaft passes through. Slurry Pump Labyrinth Part Code: B062, C062, D062, DD062XL, E062, E062XL, EE062, EE062XL, F062, F062-10, G062-10, GAM062-10, FAM062, X062, R062-1, R062DM, S062, S062DM, T062, T062DM, PV062, QV062, RV062, SV062, etc. Tobee can offer various materials as the client required, such as C23, D81, E62, G02, etc, for AH, HH, M, L, and G/GH pumps. And Slurry Pump Labyrinth are normally made in gray iron material, ductile iron is also available. And Tobee can offer various materials as the client required, such as C23, D81, E62, G02, etc.Except for the wetted parts, the pumps also are composed of many other wear parts, such as expeller, expeller ring, pump case, shaft sleeve, mechanical seal, shaft, bracket, bearing assembly etc. We supply all these spares 100% interchangeably with original and and we can guarantee the stability, substantial savings and a very competitive price. Tobee slurry pump parts are available in high chrome, gray iron & ductile iron, stainless steel, rubber and urethane material which are manufactured to maximize the abrasion and corrosion resistant. And we have stock for most of standard slurry pump spares which could deliver you within 7 days after your PO. Tobee�® Slurry Pump Spare Parts Applications: Heavy Mining | Mineral Processing | Coal Prep | Cyclone Feeds | Aggregate Processing | Fine Primary Mill Grinding | Chemical Slurry Service | Tailings | Secondary Grinding | Industrial Processing | Pulp And Paper | Food Processing | Cracking Operations | Ash Handling | Pipeline Transport | High Velocity Hydraulic Transport |Food Processing | Explosive Sludge In Metal Smelting | River And Pond Dredging | Heavy Refuse Removal | Larger Particle Or Low NPSHA Applications | Continuous (Snore) Sump Pump Operation | Abrasive Slurries | High Density Slurries | Large Particle Slurries | Sump Drainage | Washdown | Floor Drainage | Mixing
TG14x12T Gravel pump is interchangeable with 14/12T-G Pump. It is designed specifically for the continuous pumping of extremely aggressive slurries, with a wide particle size distribution. Its wear parts made from high chrome alloy, The hardness can upto HRC65, Capable of handling large particles at consistently high efficiencies resulting in low cost of ownership. The large volume internal profile of the casing reduces associated velocities further increasing component life. 14/12T-G Gravel Pump Design Features: Bearing assembly - Large diameter shaft with short overhang contributes to long bearing life. Liners - Easily replaceable liners are bolted, not glued to the casing for positive maintenance. Casing - Casing halves of cast or ductile iron provide high operating pressure capabilities. Impeller - Front and rear shrouds have pump-out vanes that reduce recirculation and seal contamination. Throat bush - Wear is reduced and maintenance is simplified by the use of tapered.
10x8S-G Gravel Pumps are the most comprehensive range of centrifugal gravel sand pumps for use in mining, chemical and general industry applications. The horizontal sand gravel pumps are designed for heavy duty applications such as mining, power sector,dredging river,and tailings as well as specialty applications, which are used for continuous pumping of high abrasive, high density sand and gravels. 10x8S-G Gravel Pump Wear Parts Design: Impeller: Front and back shroud expulsion vanes reduce gland pressure and intrusion of high concentrations of solids in the gland area. Efficiency is maintained by minimizing suction side recirculation. Specially designed and shaped impeller vanes allow the handling of extraordinarily large particles. The unique casing design and sealing vanes prevent abrasive solids intrusion at the sealing faces. Casing: Robust casing has been designed to reduce internal velocities resulting in minimum efficiency loss and improved casing wear life. The casing is made up of three components to reduce maintenance time and costs associated with a one piece design. Expeller (Centrifugal Seal): no external sealing water required where applicable. Stuffing Box: flushed gland sealing with braided packing and a lantern ring. Bearing Assembly: Tobee heavy-duty grease lubricated taper roller bearing assemblies are fitted as standard. A rigid large diameter shaft with reduced overhang minimises deflection and vibration under all conditions ensuring trouble free operation. Unusually high service factors enable the assembly to carry all radial and axial thrusts.
Tobee 10/8S-GH High Capacity Gravel Suction Pump with high chrome wear parts which design for handling large particles at river. 10x8S-GH High Head Gravel Pump is designed for continuously handling the most difficult high abrasive, big particle slurries with extra high head. The wet parts are made of high-Chrome alloys to ensure long service life. GH gravel pumps has far better performance than common gravel pumps in dredging, sand mining, barge loading and mineral processing etc. Design Features: GH high head gravel pump is cantilevered horizontal centrifugal pump designed for handling the most difficult higher abrasive slurries which contain too big solids to be pumps by a common slurry pump. Construction of this pump is of single casing connected by means of clamp bands and wide wet-passage. The wet-parts are made of Ni-hard and high chromium abrasion-resistance alloys. The discharge direction of pump can be oriented in any direction of 360 . closed impeller with wide passage, good performance of NPSH and abrasion resistance. All the wet parts are made of wear resistant high chrome alloy material. They are suitable for delivering slurry in mining, metal melting, dredging, barge loading.
Tobee 100RV SPR Rubber Lined Vertical Circulation Pumps are available in various standard lengths to suit common sump depths, for very deep sumps or where high shaft speeds limit the length of the pump. Rubber Model: 40PV-SPR, 65QV-SPR, 100RV-SPR, 150SV-SPR, 200SV-SPR, 250TV-SPR, 300TV-SPR Wet End parts: Pump Impeller: SPR40206, SPR65206,SPR10206, SPR15206, SPR20206, SPR25206, SPR30206 Pump Casing: SPR40092, SPR65092, SPR10092, SPR15092, SPR20092, SPR25092, SPR30092 Pump Back Liner: SPR40041, SPR65041, SPR10041, SPR15041, SPR20041, SPR25041, SPR30041 Impeller O-ring: RV064-S10, Discharge Pipe Gasket: SP10204, Rubber Back Liner Seal: E4124S01 RV004-1 100RV-SP Rubber Lined Vertical Slurry Pump is designed for handling abrasive and corrosive liquids and slurries, while submerged in sumps or pits. Suited for applications requiring greater reliability and durability than conventional vertical process pumps can offer. It is mainly used for pumping the slurries with high abrasive, strong corrosion and high concentration liquids contain suspended solid particles.
Specifications: Size: 8" x 6" Capacity: 360-828m3/h Head: 10-61m Speed: 500-1140rpm NPSHr: 2-9m Eff.: 72% Power: Max.120kw Handling solids: 63mm Materials: High chrome alloy, Rubber, Polyurethane, Ceramic etc Design Features: Bearing assembly - large diameter shaft with short overhang contributes to long bearing life. Liners - easily replaceable liners are bolted, not glued to the casing for positive maintenance. Casing - Casing halves of cast or ductile iron provide high operating pressure capabilities. Impeller - front and rear shrouds have pump out vanes that reduce recirculation and seal.
CQB-F Full fluoroplastic magnetic is made of fluoroplastic material with good corrosion resistance. The pump is suitable to transfer the strong acid,alkali etc chemical fluids. Perfluorinated plastic magnetic pump CQB-F perfluorinated plastic magnetic pump has the pump inlet and outlet less than DN65mm. It adopts magnetic coupling driving and there is no dynamic sealing. Therefore, it solves the phenomenon of running, blowing, dropping and leakage at shaft seal of general shaft driven centrifugal pump. The flow components of CQB-F fluoroplastic magnetic pump are made of fluoroplastics and high purity industrial ceramics, with corrosion resistance and sealing. CQB-F fluoroplastic magnetic pump has no mechanical shaft seal and no leakage. For pump inlet and outlet more than 50mm,such as DN65,DN80,DN100 etc, the flow components are made of fluoroplastic, ceramics, fluororubber and other materials. The pump body is fixed with metal materials, so the pump body is sufficient to support the weight of the pipeline and easy to use and maintain. Features: The magnetic pump has the advantages of corrosion resistance, no leakage, compact structure, beautiful appearance, small volume, low noise, reliable operation and convenient operation. Application CQB-F series fluoroplastic magnetic pump is used in petroleum, chemical industry, metallurgy, pharmacy, electroplating, environmental protection, and other industries. It can transport strong acid, strong alkali, strong oxidation, inflammable, explosive, highly toxic and precious liquids.
Shijiazhuang Naipu Pump Co., Ltd is a professional slurry pump manufacturer in China. We engage in heavy duty and severe duty material handling solutions. Our slurry pumps are manufactured to be the best standards, ensuring longer service life, higher performance, ease of operation and maintenance. The pumps are widely used in mining, construction, metallurgy, power plant, sewage water treatment, dredging, and chemical and petroleum industries. Our company is Direct factory of slurry pump, gravel sand pump , dredging pump and Spare parts,which are widely used in mine, metallurgy, coal, electric power ,dredge and other sectors of the national economy. � Our� pumps are exported� to more than� 20 countries and regions,such as South America, Africa, Southeast Asia, Russia and so on.Our products have won unanimous favorable comments from the market. Application: The type of slurry pumps are using for handing strong abrasive, high density slurries and low density, high head slurries in the metallurgical, mining, coal, power, building material and other industrial departments etc. For example: Coal washer processing, handling with the fine ore and tailings in metal mine, handing combined bottom and fly ash in a thermal power station. Contact Us Speed: Contact us or leave messages today, we will immediately reply to your inquiries within 18 hours. Type Allowable Mating Max. Power(Kw) Clear Water Performance Impeller Capacity/Q m/hr Head/m Speed/rpm Max Efficiency/% NPSH/m Nos of Vane Impeller Diameter/mm 1.5X1-NP-NAH 15 12.6--28.8 6--68 1200--3800 40 2--4 5 152 2X1.5-NP-NAH 15 32.4--72 6--58 1200--3200 45 3.5--8 5 184 3X2-NP-NAH 30 39.6--86.4 12--64 1300--2700 55 4--6 5 214 4X3-NP-NAH 30 86.4--198 9--52 1000--2200 71 4--6 5 245 6X4-NP-NAH 60 162--360 12--56 800--1550 65 5--8 5 365 8X6-NP-NAH 300 360--828 10--61 500--1140 72 2--9 5 510 10X8-NP-NAH560 612--1368 11--61 400--850 71 4--10 5 686 12X10-NP-NAH 560 936--1980 7--68 300--800 82 6 5 762 14X12-NP-NAH 560 1260--2772 13--63 300--600 77 3--10 5 965 16X14-NP-NAH 1200 1368--3060 11--63 250--550 79 4--10 5 1067 20X18-NP-NAH 1200 2520--5400 13--57 200--400 85 5--10 5 1370
"1.1kw, copper wire, oil engine, stator-92*130mm, brass head+connection, 2 brass impellers, S/S body,, S/S screw, G1'' 220V 50HZ CABLE CORD SIZE / LENGTH 5m*4 (3+1)*1mm+Euro plug"
