Model:kvh-1000 Heat supply area:200-800sq.M(2000-8000 sq.Ft) Size(lxwxh):110x55x55cm Heat exchanger:stainless steel combustion chamber Dranght fan system:two 350mm(dia) ywf Oil consumption:3-5l/h Output power:30-60kw Max.Output heat:50, 000kcal/h(200, 000btu/h) Air output:6000m3/h Fan motor:0.3kw Chimney diameter:100mm Power supply:220v 50hz Outside air compressor:1 unit outside ac is needed about 0.3-0.5cbm/min(5-9l/s) Package size(lxwxh):174x98x89cm(1.518cbm) Gross weight:210kg Use all kinds of waste oil as fuel For garage, workshop, factory, poultry farm etc Completely safe to use
Model:kvh-5000 Heat supply area:1000-1200sq.M(10000-12000 sq.Ft) Size(lxwxh):185x90x127cm Heat exchanger:stainless steel combustion chamber Dranght fan system:one 600mm(dia) ywf Oil consumption:6-8l/h Output power:80-120kw Max.Output heat:100, 000kcal/h(400, 000btu/h) Air output:12000m3/h Air output exit:2x250mm(dia) Fan motor:0.88kw Chimney diameter:140mm Power supply:220v 50hz Outside air compressor:1 unit outside ac is needed about 0.3-0.5cbm/min(5-9l/s) Package size(lxwxh):200x100x140cm(2.8cbm) Gross weight:300kg Use all kinds of waste oil as fuel For garage, workshop, poulty farm etc Completely safe to use Factory for sale Guarantee high quality
Model:kv-20 Oil consumption:13-15l/h Output power:154-195kw Max.Output heat:150, 000-200, 000kcal/h (600, 000-800, 000btul/h) Nozzle:brass siphon 2x2.0mm Tube diameter:114mm Heating pipe:1.0kw Motor power:180w Power supply:220v 50hz 110v 60hz Outside air compressor:1 unit outside ac is needed about 0.3-0.5cbm/min(5-9l/s) Package size(lxwxh):58x53x42cm Gross weight:30kg Use all kinds of waste oil as fuel Guarantee high quality Factory for sale
Model:kv-30 Oil consumption:15-21l/h Output power:216-265kw Max.Output heat:250, 000-300, 000kcal/h (1000, 000-1200, 000btu/h) Nozzle, siphon brass:3x2.0mm Tube diameter:114mm Heating pipe:1.0kw Motor power:210w Outside air compressor:1 unit outside ac is needed 0.3-0.5cbm/min(5-9l/s) Power supply:220v 50hz or 110v 60hz Pcakge size:58x53x42cm G.W:30kg Use all kinds of waste oil as fuel Factory for sale Guarantee high quality
Model:kv-50 Oil consumption:35-45l/h Output power:230-460kw Max.Output heat:450, 000-500, 000kcal/h (1, 800, 000-2, 000, 000btu/h) Nozzle:siphon brass 5x2.0mm Tube diameter:150mm Heating pipe:1.1kw Motor power:270kw Outside air compressor:1 unit outside ac is needed (0.7-1cbm/min11-17l/s) Power supply:220v 50hz or 110v 50hz Package size:70x58x55cm G.W:65kg Use all kinds of waste oil as fuel Double fire stage Guarantee high quality Factory for sale
Model:kvh-2000 Heat supply area:800-1000sq.M (8000-10000 sq.Ft) Size(lxwxh):95x56x174cm Heat exchanger:stainless steel combustion chamber Dranght fan system:four 350mm(dia) ywf Oil consumption:6-8l/h Output power:80-120kw Max.Output heat:100, 000kcal/h(400, 000btu/h) Air output:12000m3/h Fan motor:0.6kw Chimney diameter:100mm Power supply:220v 50hz Outside air compressor:1 unit outside ac is needed about 0.3-0.5cbm/min(5-9l/s) Package size(lxwxh):190x85x110cm(1.8cbm) Gross weight:300kg Use all kinds of waste oil as fuel For garage, workshop, poultry farm etc Hot wind output Completely safe to use
Structural system : 1).The crucible made of special composite steel plate does not pollute Magnesium liquid, and has antiseptic structure in it, and has long Service life 2).Stainless steel shell and panel, corrosion resistant, high temperature Resistantïzl201430063916.2ï 3).Quantitative pump instantaneous flow design, maintenance time of more Than 30 daysïzl201220249304.8ï 4).The transmission tube is made of special corrosion resistant material. It can be replaced quickly and maintained for more than 30 Days(zl201120347014.2ï 5).The preheating machine adopts a clamping mechanism, so that the Liquid level control is stable, and the feeding precision is accurate(zl201420137471.2ï 6ï.Design of anti clogging magnesium alloy elbowïzl201120322157.8ï 7ï.Perfect cleaning toolsïzl201120323381.9ï
Product features: 1). Application: heat treatment for bar, pipe, tube, shaft, bearing, billet, slab 2). Available power: 100kw-10000kw 3). Non-standard product: professional customization
Business Scope At present, leading products and business scope the company provided for customers are as follows: 1.National key new product: LF-typed three-phase single- or three-arm ladle refining furnace with capacity of 8ï½?160 tons; 2.Domestic advanced high-impedance and ultra high power EAF; 3.3200KVA-60000KVA Submerged Arc Furnace for Ferro-Alloy 4.VD, VOD and AOD type vacuum refining furnaces and process systems with capacity of 15ï½?150 tons; 5.Electrode regulating systems of EAF and ladle furnace; 6.National key new product: DW series EAF short network with capacity of 5ï½?160 tons; 7.Patented product: DB series conductive cross arm of EAF with capacity of 10ï½?160 tons; and 8.SL series of large cross-sectioned water-cooled cable suitable for EAF, refining and electric arc furnace. z
Brief Introduction Air preheater is the equipment that uses the boiler tail flue smoke to heat the entering air with its inside tubes .It is used to improve the heat exchange performance of the boiler, and reduce energy consumption. To adapt the different boiler burning type, different fuel and different fume ingredient, we developed the below enamel tube air preheaters to fit the different mediem: 1. The CFB boiler and coal powder boiler used enamel steel tubes, seam or seamless steel tube with green colour. 2. The rubbish burning furnace, biomass boiler used enamel steel tubes, seam or seamless steel tube with blue colour. 3. The Chain grate and layer burning boiler used enamel steel tubes, seam or seamless steel tube with brown colour. 4. The oil burning boiler, coking boiler and gas boiler used enamel steel tubes,seam or seamless steel tube with dark green. Why Choose Us? 1). Chinese famous brand 2). Competitive price with trusted quality 3). Short delivery lead time and excellent after-sale service 4). Certificate ISO9001, ISO14001, 5). We always produce good quality products with competitive price. 6). We have 50 professional engineers, 15 professional and technical teams for boiler improvement and more than 100 success cases of boiler energy-saving technological transformation.
We provide the clients with comprehensive and high-quality products by our exquisite and perfect technologies and offer specialized service support by highly efficient and rapid response capabilities, so as to spare no efforts in creating the utmost scientific and technological values for the clients. We sincerely hope that we can get ;;win-win;;¨¤ ending with insightful men from home and abroad hand in hand.
Our range of Muffle Furnace are best suitable for the laboratories and in various experiments. Muffle furnace is light weight with ceramic fiber wool insulation (instead of brick insulation).
Radiant tube steam superheaters are one of the most important accessories of boiler that improves the thermal efficiency. In super heaters there should not be any fins as it increases the thermal stresses and carful should be taken when choosing the superheater material that is stand for high temp and corrosion resistance. Parameter China supplier argon arc welding radiant tube steam superheater with best price We are boiler parts manufacturer, we supply boiler parts with high quality. Info.of pipes O.D. 10MM to 114MM W.T. 0.8MM to 15MM Tolerance AS STANDARD Certificated by TUV,SGS,ISO Other service Special specifications are aslo supplied according to customers' requirements Payment as the order Delivery time Within 30days upon receving the deposit, Company name  Shandong Hengtao Energy Saving & Environment Protection Co., Ltd. Market Asia,Europe,North America, Africa and so on Please feel free to contact me to know more information about the products,and warmly welcome to visit our factory when you come to China Contact information Material China supplier argon arc welding radiant tube steam superheater with best price is made of bare pipes (including carbon steel, alloy steel, heat resistant steel, etc), headers and other auxiliary materials. The pipes generally have OD32, OD38, OD42, etc or customized specifications for the users. Features With the artistic appearance and accurate size, the advance process for bending tube and welding, the first rate test equipment and sophisticated technology. Application Reheaters and superheaters are a set of tubes located in the boiler. Steam from the water walls passes to the superheaters where it is heated above its saturation temperature until the maximum required operating temperature is achieved. The superheated steam then flows through the main steam piping to the high-pressure turbine. Exhaust steam from the high-pressure turbine is guided to the boiler for reheating and from there to the intermediate and low-pressure turbines. High reheating temperatures improve the output and efficiency of a power plant.
An air preheater (APH) is a general term used to describe any device designed to heat air before another process (for example, combustion in a boiler) with the primary objective of increasing the thermal efficiency of the process. They may be used alone or to replace a recuperative heat system or to replace a steam coil. Normal air preheater exist the problem of collection of ash,worn down,low temperature corrosion to effect the safe and economical operation for the boiler unit. So HTEG established the exclusive enamel research and development center to supply the complete solution and organize the scientific reserach personnel to tacle key problems and develop the new heat transfer parts-enameld tubes air preheater The purpose of the boiler heat exchanger parts air preheater is to recover the heat from the boiler flue gas which increases the thermal efficiency of the boiler by reducing the useful heat lost in the flue gas. As a consequence, the flue gases are also conveyed to the flue gas stack (or chimney) at a lower temperature, allowing simplified design of the conveyance system and the flue gas stack. It also allows control over the temperature of gases leaving the stack (to meet emissions regulations, for example). Advantages of our product GB3274 enameled tube air preheater a).Improve and strengthen the combustion when crosses air preheater then enters the furnace, accelerates the fuel drying,the ignition and combustion process, ensures stable combustion in the furnace, and it is good for improving, strengthening the combustion effect. b). strengthen heat transfer due to improved and intensified combustion furnance and the hot air temperature in the furnace is improved, the average temperature level in the furnace is improved, thereby strengthening the furnace radiation heat transfer.
An air preheater (APH) is a general term used to describe any device designed to heat air before another process (for example, combustion in a boiler) with the primary objective of increasing the thermal efficiency of the process. They may be used alone or to replace a recuperative heat system or to replace a steam coil. Normal air preheater exist the problem of collection of ash,worn down,low temperature corrosion to effect the safe and economical operation for the boiler unit. So HTEG established the exclusive enamel research and development center to supply the complete solution and organize the scientific reserach personnel to tacle key problems and develop the new heat transfer parts-enameld tubes air preheater We have achieved ISO standard certificates as below: 1) Certificate of conformity of quality management system certification . 2) Environmental management system certificate 3) Occupational health and safety management system certificate 4)Installation, Alteration, Repair & Maintenance License of Special Equipment People's Republic of China Clients Visiting We have been reliable and steady supplier many domestic and overseas clients. We have exported products of economizer, membrane water wall, gas fired boiler etc to vietnam, mongolia, parkistan, indonesia these years and won great appraisal from clients for good price and finest quality.
In power station boilers, the effect of superheaters is to heat the steam to certain temperature for higher efficiency of the power station. Reheaters are steam superheaters to reheat the over-worked long-pressure or middle-pressure steam to certain temperature. The use of rehearters can further improve heat power of the power station circulating and control the steam temperature of the end blades of the steam turbine within allowed range. Zigzag superheaters and reheaters of the Company are also unique with rigorous production technique, first-class production flow line and complete test methods. Accessory of customer design zigzag Typed Tube heat exchanger Superheater for Coal Fired Boiler It is consisted of a serious of bare coil (carbon steel, alloy steel, or durable heat steel) and header and other auxiliaries. Tubes Ï?32, 38, 42 and so on, also as the request. Structure Horizontal or vertical. Characteristic of customer design zigzag Typed Tube heat exchanger Superheater for Coal Fired Boiler With the artistic appearance and accurate size, the advance process for bending tube and welding,the first rate test equipment and sophisticated technology.
The circulating fluidized bed boiler headers collect and distribute steam or water from or to a series of smaller pipes or conduits. They are made of carbon or ferritic steel, generally of the same grade as the piping systems. Unlike piping systems which are usually butt welded and bent, the boiler spare part headers are straight. Features 1. Strength calculation report with applied materials information; 2. 100%NDT(non-destructive inspection) report of steel plate, tube and welding rod; 3. 100%X-ray inspection report (welding seam): to ensure the quality of the entire boiler; 4. Hydraulic test report: ensure the standard working pressure and safet Application Save energy high pressure welding manifold headers for distributionrs collect and distribute steam or water from or to a series of smaller pipes or conduits.Manifold headers are made of carbon or ferritic steel, generally of the same grade as the piping systems. Unlike piping systems which are usually butt welded and bent, headers are straight.
Induction melting furnace is a kind of induction heating machine. For different requirement, some adopt medium frequency power and some adopt super audio frequency power. Induction melting furnace is a clean and energy saving power. Itâ??s widely used in small capacity metal melting. Like copper, aluminum, gold and so on.
1Main Characteristics 1.IGBTmodule and soft switching inverting technologies are as in the protection of the generator,Higher reliability can do. 2.Small and portable ,compared with SCR controlled machine,Only 1/10 working space is needed 3.high efficiency to save energy,high efficiency and power fator can be maintained 4.the generator is adatable in large frequency range from 1KHZ to 20KHz,installation can be done easily according to our manual. 5.100% duty cycle continous working ability at maximum power. 6.constant power or constant voltage control mode. 7.display of output power ,output frequency and output voltage. 2�Technical Parameter Model No.: CW-MF-300 Input Power Max 300KW Output Power Max 70--550V Input Power Desire Three Phase ,380V±20% , 50 or 60HZ Oscillate Frequency 1KHZ-20KHZ according to the applicationNormal Frequency : 4KHZ�8KHZ�11KHZ�15KHZ�20KHZ Duty Sycle 100% 24 Hours continuous working Gross Weight 160KGS Meas .(cm) 40(W)*88(H)*76(L)
1Main Characteristics 1.IGBTmodule and soft switching inverting technologies are as in the protection of the generator,Higher reliability can do. 2.Small and portable ,compared with SCR controlled machine,Only 1/10 working space is needed 3.high efficiency to save energy,high efficiency and power fator can be maintained 4.the generator is adatable in large frequency range from 1KHZ to 20KHz,installation can be done easily according to our manual. 5.100% duty cycle continous working ability at maximum power. 6.constant power or constant voltage control mode. 7.display of output power ,output frequency and output voltage. 2�Technical Parameter Model No.: CW-MF-15 CW-MF-25 CW-MF-35 CW-MF-45 CW-MF-70 CW-MF-90 CW-MF-110 CW-MF-160 Input Power Max 15KW 25KW 35KW 45KW 70KW 90KW 110KW 160KW Output Power Max 70-550V 70-550V 70-550V 70-550V 70-550V 70-550V 70-550V 70-550V Input Power Desire Three Phase ,380V±20% , 50 or 60HZ Oscillate Frequency 1KHZ-20KHZ according to the applicationNormal Frequency : 4KHZ�8KHZ�11KHZ�15KHZ�20KHZ Duty Sycle 100% 24 Hours continuous working Gross Weight 24KG 24KG 34KG 36KG 51KG 79KG 94KG 130KG Meas .(cm) 27(W)x47(H)x56(L)cm 35x65x65cm 40x88x76cm
