Stainless Steel Pleated Filter Cartridge Stainless steel pleated filter cartridge demonstrate good permeability, high tensile strength and are available from single wrap designs through to complex multi-layered structures in pleated constructions to optimise the area available. These meshes can be manufactured in diffusion bonded versions to increase performance security of pore shape and size and have the broadest range of pore sizes of any filter media type.The pleated design provides maximum surface area for higher flow rates and longer run times. With metal construction, these cartridges can be cleaned and put back into service, resulting in a longer service life than other types of media. ZHUAN LV PM series precision woven meshes are manufactured in various types of weaves. Plain square weave is available for simple sieving duties through various weave patterns (Reverse Plain Dutch, Broad Mesh Twill and Single Plain Weave). Dutch Twill Weave is provided for the most comprehensive selection of surface filtration duties. ZHUAN LV PM series filter cartridge is available in 316L stainless steel as standard with other alloys such as 304L stainless steel,Inconel and Monel on request.
Stainless Steel Filter Cartridges/Elements Stainless Steel Filter Cartridges Stainless steel cartridges are filters made of multiple layers of stainless steel 304/316 mesh with a protective stainless steel cartridge housing. The middle mesh layer determines the filtration efficiency and is covered with an outer and inner layer of coarser mesh to provide support and protection. These stainless filter cartridge can be designed in plain cylindrical or pleated configurations to increase the filtration area. Working Principle Stainless steel cartridges capture or block impurities (e.g., chemical and physical impurities) in the fluid as it flows through. Wide range of applications Power Generation Water Treatment Chemical Processing High Pressure Differential Corrosive oil and gas High Temperature Electronics Factory equipment
Expanded Metal Filters Expanded metal filters are stretched into various hole shapes using a special process with no welded surfaces, making them stronger and more robust than welded wire mesh. In some filtration applications with harsh environments, steel plate mesh cartridges last longer than welded cartridges. In filter element applications, expanded metal filters are often made into tubular shapes for filtering solids, water and other substances. Expanded metal filters are also used as a support mesh for filter elements made of other materials such as woven wire mesh and carbon filter elements. We also manufacture a range of formed filtration components, from vent ridge tiles for roof ventilation to small bullet filters for domestic heating systems, and our in-house tooling capabilities enable us to assist customers in developing new filtration products. Our range of mesh filtration solutions includes Filtafoil â?? our aluminium foil can be layered into filter panels to capture dust and grease for both internal and external air filtration. Filter panels â?? we can supply made to order products with frames and backing meshes constructed in stainless steel, aluminium, galvanised steel and tinplate, in thickness ranging from 7mm to 50mm. The infill options include Filtafoil, bondina, and galvanised and stainless steel.
High quality Oil Gas Separator 2901034300 1613750200 GA22 Filter element Air compressor maintenance accessories air compressor.The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
High Quality Fiberglass Material 2901162600 1622314000 Screw Air Compressor Air Oil Separator Filter.The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
Air/Oil Separator 42542787 Replacement Compatible Filter Element for Ingersoll Rand No reviews yet.The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
Replacement For Kobelco 75HP Air Compressors Air Oil Separator Part Number P-Ce03-578 P-Ce03-596 P-Ce03-592.The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
Replacement For Atlas Copco Air Oil Separator Filter1604038200 2911007500 2911011602 1615769500.The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
2116010085/2116010086 Oil-Gas Separator for Fusheng Air Compressor Machine.The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
Oil Separator 2202929400 for Atlas Copco Compressor 2202929450 1630404600.The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
Oil Separator 2202929400 for Atlas Copco Compressor 2202929450 1630404600.The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
6221372800 Oil Separator Compressor Replacement Filter Substitute Spare Parts.The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
Replacement For Kaeser Air Compressor Parts Air Oil Separator 6.4334.0.The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
1625481101 1625481100 Air Oil Separator for Atlas Copco Air Compressor Filter 1625481150.The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
13010174 A13010174 Air Oil Separator for CompAir L-15 Air Compressor Filter Element.The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
24121212 22388045 Air Oil Separator Filter Element for Ingersoll-Rand Screw Air Compressor Part Filter.The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
Oil Separator 6221372850 6221372800 Industrial Compressor Parts.The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
Oil Separator 6221372400 for Atlas Copco Screw Air Compressor Replacement Filter 6221372450.The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
High performance For Kobelco replacement oil air separator filter P-CE03-572 For Air Compressor Parts.The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
