Hot Air Ballooning /Fall Protection Stamped Steel Snap Hook Sheet steel,Heat treated 100% Proof loaded to 3600lbs/16kN Min. Breaking load: 5000lbs/23kN Net weight: 190g Meets or Exceeds: EN362-2004
Steel Snap Hook For Climbing And Emergency Rescue Sheet steel,Heat treated 100% Proof loaded to 3600lbs/16kN Min. Breaking load: 5000lbs/23kN Net weight: 790g Meets or Exceeds: EN362-2004
Climbing Swivel Survival Steel Snap Hook Sheet steel,Heat treated 100% Proof loaded to 3600lbs/16kN Min. Breaking load: 5000lbs/23kN Net weight: 234g Meets or Exceeds: EN362-2004
Climbing Swivel Survival Steel Snap Hook Sheet steel,Heat treated 100% Proof loaded to 3600lbs/16kN Min. Breaking load: 5000lbs/23kN Net weight: 472.3g Meets or Exceeds: ANSI Z359.12-19CSA Z259.12-16\EN362-2004
1. nominal size: Nominal diameter of the round section steel wire or bar from which the chain is made. 2. material diameter: Diameter of the material in the chain link as measured. 3. weld diameter: Diameter at the weld as measured. 4. length dimensionally affected by welding: Length on either side of the center of the link, affected by welding. 5. pitch: Internal length of a link as measured. 6. manufacturing proof force(MPF) of chain: Force to which during manufacture the whole of the chain is subjected. 7. breaking force( BF): Maximum force which the chain withstands during the course of a static tensile test to destruction. 8. working load limit (WLL) of chain: Maximum mass which the chain hanging vertically is authorized to sustain in general lifting service. 9. total ultimate elongation (A): Total extension at the point of fracture of the chain expressed as a percentage of the internal length of the test sample. 10. processing: Any treatment of the chain subsequent to welding, for example, heat treatment, polishing or dimension calibration. 11. lot: Specified quantity from which test sample(s) is/are selected. 12. competent person: A designated person, suitably trained qualified by knowledge and practical experience, and with the necessary instructions to enable the required examination to be carried out.
Short link chain for lifting purposes Conforms to the latest revision Grade 100 chain is 25% stronger than Grade 80 chain. Enables you to perform some lifts with lighter weight chain. Produced from the highest quality alloy steel Embossed with G100 and traceability code Quenched and tempered, proof tested In accordance with 4-to-1 design factor required by AS 2321 standard. Blue electrophoresis finish or black electrophoresis finish WARNING: DO NOT EXCEED THE WORKING LOAD LIMITS
Specifically recommended for overhead lifting Grade 100 chain is 25% stronger than Grade 80 chain. Enables you to perform some lifts with lighter weight chain. Meet the latest guidelines of ASTM A973 specifications Produced from the highest quality alloy steel Embossed with G100 and traceability code Quenched and tempered, proof tested In accordance with 4-to-1 design factor required by the ASTM A973 specifications Blue electrophoresis finish or black electrophoresis finish WARNING: DO NOT EXCEED THE WORKING LOAD LIMITS
Specifically recommended for overhead lifting Grade 100 chain is 25% stronger than Grade 80 chain. Enables you to perform some lifts with lighter weight chain. Meet the latest guidelines of the Produced from the highest quality alloy steel Embossed with and traceability code Quenched and tempered, proof tested In accordance with 4-to-1 design factor required by the specifications Blue electrophoresis finish or black electrophoresis finish WARNING: DO NOT EXCEED THE WORKING LOAD LIMITS
Welcome to buy the newest and competitive price DIN5687-80 G80 Lifting Chain, Grade 80 Alloy Lifting Chain from our factory. We're one of the leading manufacturers and suppliers, offering you the wholesale service and the OEM service at a discount. With CE certification, our products made in in stock are high in quality and low in price. Please be free to get the free sample from us.
Material: High-Quality Alloy Steel Surface treatment: Self-color, Polishing, Blackened,Painted, Plastic Coating, Hot-Dip Manufacture Standard: ISO, DIN, BS, JIS, ASTM Quality Grade: G80/G100 Safety Factor: MIN 4 Product Marking: Required by client We also can make the non-standard chain according to the clients' requirements.
Short link chain for lifting purposes Conforms to the latest revision Standard Grade 100 chain is 25% stronger than Grade 80 chain. Enables you to perform some lifts with lighter weight chain. Produced from the highest quality alloy steel Embossed with G100 and traceability code Quenched and tempered, proof tested In accordance with 4-to-1 design factor required by AS 2321 standard. Blue electrophoresis finish or black electrophoresis finish WARNING: DO NOT EXCEED THE WORKING LOAD LIMITS
AS2321 Short Link Chain Grade T ( 80 ), G80 Alloy Chain, Grade 80 Short Link Chain for Chain Slings
Welcome to buy the newest and competitive price DIN5687-80 G80 Lifting Chain, Grade 80 Alloy Lifting Chain from our factory. We're one of the leading manufacturers and suppliers, offering you the wholesale service and the OEM service at a discount. With CE certification, our products made in stock are high in quality and low in price. Please be free to get the free sample from us.
Code No. Nominal Size Material Diameter Working Load Limit(MAX) Proof Test(MIN) Breaking Force MIN Inside Length (MAX) Inside Width(MIN) MM IN MM IN KG LBS KN LBS KN LBS MM IN MM IN DS-C0141 7.0 1/4 7.0 0.281 1430 3150 28.0 6300 56.0 12600 31.8 1.24 9.8 0.38 DS-C0142 8.7 5/16 8.7 0.343 2130 4700 41.8 9400 83.6 18800 32.8 1.29 11.2 0.44 DS-C0143 11.9 3/8 10.3 0.406 2990 6600 58.7 13200 117.4 26400 35.0 1.38 14.0 0.55 DS-C0144 13.0 1/2 13.5 0.531 5130 11300 100.4 22600 200.8 45200 45.5 1.79 18.2 0.72 DS-C0145 16.0 5/8 16.0 0.630 7170 15800 140.4 31600 280.8 63200 56.0 2.20 20.0 0.79 DS-C0146 20.0 3/4 20.0 0.787 11200 24700 219.6 49400 439.2 98800 70.0 2.76 25.0 0.98
Technical Information chain and fittings are NOT SUITABLE FOR INDUSTRIAL LIFTING PURPOSES. Note: Dimensions and masses subject to commercial tolerances and design changes without notice. Welcome to buy the newest and competitive price Standard Chain Assembly with Cradle Grab Hook Each End from our factory. We're one of the leading manufacturers and suppliers, offering you the wholesale service and the OEM service at a discount. With CE certification, our products made in stock are high in quality and low in price. Please be free to get the free sample from us.
Three-Link Chain for Coal Transfer Grade B Size(d) Pitch(p) Min. Inside Width(a) Max. Outside Width(b) Curve Radius(r) Test Load Max. Elongation at Test Load Min. Breaking Load Min. Total Elongation at Fracture 3 Links(Weight) mm mm mm mm mm kn kn kn 22 105 40 87 41 70 2 370 15 2.9 26 118 46 102 48 100 2 520 15 4.6 28 120 48 108 51 110 2 610 15 6.7 30 120 48 112 53 120 2 670 15 7.8 30 130 55 119 56.5 120 2 670 15 6.9 Three-Link Chain for Coal Transfer Grade C Size(d) Pitch(p) Min. Inside Width(a) Max. Outside Width(b) Curve Radius(r) Test Load Max. Elongation at Test Load Min. Breaking Load Min. Total Elongation at Fracture 3 Links(Weight) mm mm mm mm mm kn kn kn 22 105 40 87 41 135 2 530 15 2.9 26 118 46 102 48 190 2 740 15 4.6 28 120 48 108 51 220 2 860 15 6.7 30 120 48 112 53 250 2 990 15 7.8 30 130 55 119 56.5 250 2 990 15 6.9
Specifically recommended for overhead lifting Produced from the highest quality alloy steel Embossed with G80 and traceability code Quenched and tempered, proof tested In accordance with 4-to-1 design factor required specifications Black electrophoresis finish WARNING: DO NOT EXCEED THE WORKING LOAD LIMITS
Short link chain for lifting purposes Conforms to the latest revision Standard 2321 Produced from the highest quality alloy steel Embossed with G80 and traceability code Quenched and tempered, proof tested In accordance with 4-to-1 design factor required by AS2321 standard. Black electrophoresis finish WARNING: DO NOT EXCEED THE WORKING LOAD LIMITS
Definitions to European standard EN 818-7 For the purposes of this Part of EN 818,the following definitions apply: 1. nominal size: Nominal diameter of the round section steel wire or bar from which the chain is made. 2. material diameter: Diameter of the material in the chain link as measured. 3. weld diameter: Diameter at the weld as measured. 4. length dimensionally affected by welding: Length on either side of the center of the link, affected by welding. 5. pitch: Internal length of a link as measured. 6. manufacturing proof force(MPF) of chain: Force to which during manufacture the whole of the chain is subjected. 7. breaking force( BF): Maximum force which the chain withstands during the course of a static tensile test to destruction. 8. working load limit (WLL) of chain: Maximum mass which the chain hanging vertically is authorized to sustain in general lifting service. 9. total ultimate elongation (A): Total extension at the point of fracture of the chain expressed as a percentage of the internal length of the test sample. 10. processing: Any treatment of the chain subsequent to welding, for example, heat treatment, polishing or dimension calibration. 11. lot: Specified quantity from which test sample(s) is/are selected. 12. competent person: A designated person, suitably trained qualified by knowledge and practical experience, and with the necessary instructions to enable the required examination to be carried out.
Application: Excavator Certification: CE, ISO9001: 2000 Condition: New Excavator Undercarriage Parts: Track Chain, Track Link, Track Shoes Assembly Machinery Model: R180LC-9 R180LC-7A Quality: High Quality with Cheap Price Delivery Time Usually Within 15 Days After Payment Receipt Payment Term T/T, L/C at Sight, Western Union Transport Package Cartons, Wooden Cases Specification R180LC-9 R180LC-7A Trademark QINDING Origin Shandong, China HS Code 84314999 Production Capacity 5000 PCS Per Month
