Storage Tanks , Water Filters, Water Treatment Plants .
Description Two component, air drying, high solids, Epoxy coating. The product has the advantage of epoxy resin composition with speciality pigment, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to completely wet the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. The composition has been balanced to a convenient mixing ratio by volume with excellent application characteristics. The ZERO solvent content reduces the problem of lifting of the paint film and adhesion failure by blistering and pin holing. This assures a stable long term performance. Recommended Use :- It is mainly recommended in those areas where blasting is impractical or impossible. Uses include steel structures in Industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, water tank, pipelines etc. for application on tank exteriors and interiors, structural steel, pipelines, machineries, vessels, etc. Physical Data COLOUR : Selected industrial shades FINISH : Semi glossy SOLIDS BY VOLUME : 80 �± 2% THEORETICAL SPREADING RATE : 10 sq.mt. / ltr. at a recommended DFT of 80 �µ FLASH POINT : Base : Above 25�°C Hardener : Above 25�°C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30�°C) : SURFACE DRY : 4 hours FULL CURE : 7 days HARD DRY : Overnight SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data :- MIXING RATIO Base : Hardener ( As per our recommendations) : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Airless Spray POT LIFE : 2 - 3 hours min at 30�° C RECOMMENDED DFT : 75-100 mic. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU
Dosing Tank Capacity: 100 LIT. MOC:LLDPE.
ISO tanks T1, T4, T11, T14
ISO tanks T1, T4, T11, T14
PP tank use for Chemical industries, or agro industries
Feed water tanks
We are manufacturer for Liquid Nitrogen containers ranging from 0.5 Ltr till 35 Ltrs, even can make as per your requirements. We are supplying in India to various limited companies. We can also supply Epoxy Insulation Tubes. Kindly send me your detailed requirements so that we can quote you the best rates FOB / CIF.
Inflatables Products With the experience of several years in rubber industry Zenith has now entered in inflatable products section and introduced range of products which include Air Cell, Gas Holder Balloon, Inflatable work boats and Life Rafts. The primary reason that Zenith holds for being great at making inflatable products is the state-of-the-art infrastructure for manufacturing inflatable products. The inflatable products undergo complete controlled manufacturing, from compounding to dispatch of finished products and extensive research & development gives Zenith a competitive edge over its competitors. Zeniths’ quality and manufacturing procedures are strictly in accordance with ISO 9001:2008, ISO 14001:2004 and ZENITH’s extensive R&D facilities are available to investigate new products and materials to meet the needs of our customers. Zenith certifications & awards assure highest quality products to its customers’ business requirements and needs.
Inflatables Products With the experience of several years in rubber industry Zenith has now entered in inflatable products section and introduced range of products which include Air Cell, Gas Holder Balloon, Inflatable work boats and Life Rafts. The primary reason that Zenith holds for being great at making inflatable products is the state-of-the-art infrastructure for manufacturing inflatable products. The inflatable products undergo complete controlled manufacturing, from compounding to dispatch of finished products and extensive research & development gives Zenith a competitive edge over its competitors. Zeniths’ quality and manufacturing procedures are strictly in accordance with ISO 9001:2008, ISO 14001:2004 and ZENITH’s extensive R&D facilities are available to investigate new products and materials to meet the needs of our customers. Zenith certifications & awards assure highest quality products to its customers’ business requirements and needs.
Inflatables Products With the experience of several years in rubber industry Zenith has now entered in inflatable products section and introduced range of products which include Air Cell, Gas Holder Balloon, Inflatable work boats and Life Rafts. The primary reason that Zenith holds for being great at making inflatable products is the state-of-the-art infrastructure for manufacturing inflatable products. The inflatable products undergo complete controlled manufacturing, from compounding to dispatch of finished products and extensive research & development gives Zenith a competitive edge over its competitors. Zeniths’ quality and manufacturing procedures are strictly in accordance with ISO 9001:2008, ISO 14001:2004 and ZENITH’s extensive R&D facilities are available to investigate new products and materials to meet the needs of our customers. Zenith certifications & awards assure highest quality products to its customers’ business requirements and needs.
Inflatables Products With the experience of several years in rubber industry Zenith has now entered in inflatable products section and introduced range of products which include Air Cell, Gas Holder Balloon, Inflatable work boats and Life Rafts. The primary reason that Zenith holds for being great at making inflatable products is the state-of-the-art infrastructure for manufacturing inflatable products. The inflatable products undergo complete controlled manufacturing, from compounding to dispatch of finished products and extensive research & development gives Zenith a competitive edge over its competitors. Zeniths’ quality and manufacturing procedures are strictly in accordance with ISO 9001:2008, ISO 14001:2004 and ZENITH’s extensive R&D facilities are available to investigate new products and materials to meet the needs of our customers. Zenith certifications & awards assure highest quality products to its customers’ business requirements and needs.
We are manufacturer of water storage tank. Diffrent capacity and layers available. 1 layer to 7 layers tanks we manufacture. Different colors available
Pickling Tanks are used in surface treatment industries I.e. Galvanizing, pickling, electroplating.
Water tank .
Water tanks.
Storage tanks.
MS and SS tanks..
Advanced non filling micro bio tanks .Manufactures and installs
Micro bio tanks .Manufactures and installs