ASTM A335 P22 alloy pipeA leading manufacturer, exporter, suppliers & stock holder of ASTM A335/ASME SA335 P22 High Pressure Steel Pipe & we provide a comprehensive range of ASTM A335/ASME SA335 P22 High Pressure Steel Pipe.
We manufacture ASTM A335/ASME SA335 P22 High Pressure Steel Pipe & ASTM A335 P1/P2/P5/P5b/P5c/P9/P11/P12/P22/P23/P91/P92 tubing in India for export all arround the world
ASTM A335/ASME SA335 P22 High Pressure Steel Pipe Chemistry Composition
C, % Mn, % P, % S, % Si, % Cr, % Mo, %
0.05-0.15 0.30-0.60 0.025 max 0.025 max 0.50 max 1.90-2.60 0.87-1.13
ASTM A335/ASME SA335 P22 High Pressure Steel Pipe Mechanical Properties
Tensile Strength , MPa Yield Strength, MPa Elongation, %
415 min 205 min 30 min
We are the Manufacturer of HR Pickled Side Channel in 14g/12g/10g/ And 8 g in 7/8/9/ and 10 Feet .Our sIZES ARE 2.5",3.0", AND 3.75" . Our side channel are mainly manufactured From HR Pickled Sheets ,Directly Purchased From Tata,JSW And Other Companies
Galvanization or galvanizing (also spelled galvanization or galvanizing) is the process of applying a protective zinc coating to steel or iron, to prevent rusting. The most common method is hot-dip galvanizing, in which the parts are submerged in a bath of molten hot zinc.
JRS Pipes and Tubes is India one of the most trusted MS rectangular pipe dealers with tubes in a wide range of dimensions and thicknesses. We specialize in offering our customers with custom thickness rectangular steel pipes for critical and special applications. Also commonly known as Rectangular Hollow Sections (RHS), rectangular pipes and tubes can be supplied with black paint mill finish or with anti rust oil coating for surface protection of the pipes. Rectangular steel pipes both in seamless and welded form are widely used for structural purposes, architectural work, special piping systems and many other general purpose fabrication works. Rectangular steel pipes can be offered in both mechanical and structural grades, as per the requirement of our customers.
Applications of Rectangular Steel Tubes & Welded Rectangular Hollow Section
Furniture
General Steel Fabrications
Structural Work
Racks
Engineering Applications
Special Shape Piping Systems
Rebar couplers are used in reinforced concrete structures to replace normal rebar lap joints. The couplers are also suitable for use in reinforced concrete columns and walls. Each rebar coupler consists of a piece of rebar equipped with a thread and coupler sleeve at the right end as viewed in the direction of installation. In construction joints, rebar couplers can be used to replace all pieces of rebar going through the formwork.
Rebar couplers are used in reinforced concrete structures to replace normal rebar lap joints. Each rebar coupler consists of a piece of rebar equipped with a thread and coupler sleeve at the right end as viewed in the direction of installation. ...
We are a leading Manufacturer, Traders and supplier of galvanized steel sheet. Galvanization is the process of applying a protective zinc coating to steel or iron in order to prevent it from rusting. The term is derived from the name of Italian scientist Luigi Galvani. Galvanized iron (GI) sheets are steel sheets which are basically coated with zinc and include a range of hot dip galvanized and electro-galvanized steel sheets. Zinc weathers at a very slow rate, so the coating generally has a long life. Zinc has a greater electro-negativity than iron and hence provides cathodic (or sacrificial) protection to the steel. This results in the zinc corroding in preference to the steel if the coating is chipped or damaged to expose the base metal. Besides acting as galvanic protector, The other functions of the zinc layer are as follow:
To retain the steel intact with its full initial strength.
To provide the surface a more pleasing appearance.
To increase the life of any suitable organic finishing system applied over it.
To protect the steel from corrosive attack in most atmospheres, acting as a continuous and lasting shield between steel and the atmosphere.
Features
Uniform zinc coating in the range of 60-600 GSM
Spangles: Zero / regular / minimized / suppressed
Surface finish: Normal spangle, large spangle, small spangle, matte surface
With and without tension leveling
Passivation: Chromated (Hexavalent / Trivalent)
Oiling: 100-1,000 GSM
Winding: Controlled / staggered (+/- 5 to +/-15mm)
Coil id: 508 / 610 mm
Elongation: 16-33%.
Dimensions
Thickness: 0.18 - 3.2 mm
Width: 800 - 1,500 mm
Length: Up to 2,500 mm
Grades & Standards
CQ, DQ, DDQ, EDDQ, HSLA
ASTM A653, SS33/37/40/50/60/80, EN 10327, JIS
Commercial Steel (CS Types A, B, and C)
Forming Steel (FS Types A and B)
Deep Drawing Steel (DDS Types A and C)
Extra Deep Drawing Steel (EDDS)
Structural Steel (SS) further designated by Grades (33,37,40,50,80)
High Strength Low Alloy Steel (HSLAS)
Supply condition
Coil / Slits/ Sheet form
We are a leading Manufacturer, Traders and supplier of galvanized steel sheet. Galvanization is the process of applying a protective zinc coating to steel or iron in order to prevent it from rusting. The term is derived from the name of Italian scientist Luigi Galvani. Galvanized iron (GI) sheets are steel sheets which are basically coated with zinc and include a range of hot dip galvanized and electro-galvanized steel sheets. Zinc weathers at a very slow rate, so the coating generally has a long life. Zinc has a greater electro-negativity than iron and hence provides cathodic (or sacrificial) protection to the steel. This results in the zinc corroding in preference to the steel if the coating is chipped or damaged to expose the base metal. Besides acting as galvanic protector, The other functions of the zinc layer are as follow:
To retain the steel intact with its full initial strength.
To provide the surface a more pleasing appearance.
To increase the life of any suitable organic finishing system applied over it.
To protect the steel from corrosive attack in most atmospheres, acting as a continuous and lasting shield between steel and the atmosphere.
Features
Uniform zinc coating in the range of 60-600 GSM
Spangles: Zero / regular / minimized / suppressed
Surface finish: Normal spangle, large spangle, small spangle, matte surface
With and without tension leveling
Passivation: Chromated (Hexavalent / Trivalent)
Oiling: 100-1,000 GSM
Winding: Controlled / staggered (+/- 5 to +/-15mm)
Coil id: 508 / 610 mm
Elongation: 16-33%.
Dimensions
Thickness: 0.18 - 3.2 mm
Width: 800 - 1,500 mm
Length: Up to 2,500 mm
Grades & Standards
CQ, DQ, DDQ, EDDQ, HSLA
ASTM A653, SS33/37/40/50/60/80, EN 10327, JIS
Commercial Steel (CS Types A, B, and C)
Forming Steel (FS Types A and B)
Deep Drawing Steel (DDS Types A and C)
Extra Deep Drawing Steel (EDDS)
Structural Steel (SS) further designated by Grades (33,37,40,50,80)
High Strength Low Alloy Steel (HSLAS)
Supply condition
Coil / Slits/ Sheet form
Parameters:
Thickness: 0.30 4.00 mm
Width: 600- 1500 mm
Length: 1000 7000 mm
Temper: 1/8 Hard, Hard, Hard, Full Hard,
Finish: Dull, Matt, Bright, Mirror
Grade: D, DD, EDD, Super EDD
Edge: Mill edge, Slit edge
CTL: Up to 4500mm with tolerance of +2/-0 mm(Further close tolerance
on - request)
Surface Finish: Super Bright, Bright, Dull & Matte. (RaValuewith controlled Rmax on request).
Grades: Specifications - As per JIS/BIS/ ASTM/EN Standards
Low Carbon CRCA Grades
Super EDD/EDD/DD/D (SPCX, SPCEN, SPCD, SPCC) non-aging, IF-High
Strength steel (IF-HSS), High Strength Low Alloy Steel (HSLA), viz., ST -42,
ST-45, ST-52, SAPH-400/41O, Steel for Porcelein Enammeling, Corrosion
Resistant Steel, viz., Tin Mill Black Plate (TMBP)
Medium & High Carbon CRCA Grades
C- 30, C-40,MC -ll, EN - 8, C-55, MC-12,
EN- 9 C-62, C-60, C-80, HC-14, EN-42J
ELECTRICAL Grades Elec -I, Elec-n, Elec-nI, SemiProcessed Elect. Steel
OTHER CRCA Grades
Case Hardening Steel- 15Cr3, SAE 1010, SAE 1012
Through Hardening Grades- SAE 1040, SAE 1045, 1055, 1065, 1080, 1541
specification
item hot rolled medium and high tensile structural steel â?? is 2062 e250br
thickness 1.6mm-20mm
width 1000mm-2100mm
length 3000mm-18000mm
chemical composition of is 2062 e250br plate
grade c mn s p si carbon equivalent (ce), max
is 2062 e 250 br 0.22 1.50 0.045 0.045 0.40 0.41
mechanical properties of is 2062 e250br plate
grade yield strength n/mm2 tensile strength n/mm2 elongation (%)
is 2062 e250 br 250 min 410 min 23
plates sheets 1 mm to 300 mm thickness cold rolled, hot rolled
Dimensions
Thickness: 0.15-3.2 mm
Width: 900 - 1,500 mm
Length: Up to 2,500 mm
Oiling: 100-1,000 GSM
Winding: Controlled / staggered (+/- 5 to +/-15mm)
Coil id: 508 / 610 mm
Elongation: 16-33%.
Grades & Standards
CQ, DQ, DDQ, EDDQ, HSLA
ASTM A653, SS33/37/40/50/60/80, EN 10327, JIS
Commercial Steel (CS Types A, B, and C)
Forming Steel (FS Types A and B)
Deep Drawing Steel (DDS Types A and C)
Extra Deep Drawing Steel (EDDS)
Structural Steel (SS) â?? further designated by Grades (33,37,40,50,80)
High Strength Low Alloy Steel (HSLAS)
Supply condition
Coil / Slits/ Sheet form
Dimensions
Thickness: 0.4-3.2mm (CRCA); 0.15-1.9mm (CRFH)
Width: 800-1,625mm
Material - Mild Carbon Steel
Length - Can be cut to sheets according to requirement
Max. Weight - 20MT per coil
Grades
Extra Deep Drawing steels (EDD, IF)
IFHS (350, 400, 440)
Bake hardening steel (BH180,220)
HSLA (320, 340, 440)
Semi-processed electrical steels
Steels for enameling
CORTEN
ASTM: A 1008: DS type A & B, DDS, EDDS, EDDS+
IS: IS 513: D, DD, EDD
DIN: DIN 17100: ST 37.3, ST 44.2, ST 44.3, ST 52.3
EN: EN 10268: HSLA 340, HSLA 420,EN 10130: DC 01, 03, 04, 05/06
JIS: G 3141: SPCD, SPCE, SPEN, SPRC 340/ 390,SPFC 340/ 390/ 440
Supply Condition:
Coil / Slit / Sheet form
Surface textures
a. Smooth (plating applications) - suitable for electroplated
articles and also for re-rolling when a matt texture is undesirable. A maximum surface roughness
of 0,5 micrometers centre line average (CLA) is aimed for. Typical applications are car bumpers,
door locks and other electroplated articles.
b. Light matt (drawing and pressing applications)- surface roughness of 0.60 -
1,25 micrometers centre line average (CLA) and 100 peaks per inch (PPI) minimum is aimed for.
Typical applications are automobile panels.
c. Medium matt (drawing and pressing applications)- A surface roughness of 0,8 - 1,6 micrometers centre line average (CLA) and 100 peaks per inch
(PPI) minimum is aimed for. Typical applications are drum bodies and ends.
Dimensions
Thickness: 1.6 -25mm
Width: 900-2,100mm
Material - Mild Carbon Steel
Max. Weight â?? 22 â?? 25 MT
Grades
Drawing quality steel: D / DD / EDD
Cold rolling grades: IF (Interstitial Free) and High Strength IF Steels
Medium carbon / high carbon steels
High strength steels: JIS G 3113 SAPH310/370/400/440, JIS G 3134 SPFH-540/590, EN 10149-2 S550MC/S650MC, DP590
Line pipe â?? API X42 to X-80 grades (Sour and Non Sour Applications)
Boilers and pressure vessels grades
Ship building grades
Corrosion resistant steel
Re-rolling/ Drawing Grades,
Tube and Pipe/ Forming Grades,
Structural/ Medium Tensile Tube/ Forming Grades,
LPG/ Low Pressure Vessel Grades,
HSLA Grades,
Medium Carbon Grades,
Weather Resistance Grades,
Line Pipe Grades,
Chequered Plates
ASTM (USA) : A 36 A572: Gr 42, Gr 50
IS (INDIA) : IS 2062: E250 Gr A/ B/ C, E350 Gr A/ B/ C
DIN (GERMANY) : DIN 17100: ST 37.3, ST 44.2, ST 44.3, ST 52.3
BS (ENGLAND) : BS 4360: 40, 43, 50
EN (EUROPE) : EN 10025: S235, S275, S355
JIS (JAPAN) : G 3106: SM400, SM 490 G 3101: SS400, SS490
