Rebar couplers are used in reinforced concrete structures to replace normal rebar lap joints. Each rebar coupler consists of a piece of rebar equipped with a thread and coupler sleeve at the right end as viewed in the direction of installation. ...
Termipore pipe - TP125175 â?? Inside diameter 12.5 , outside diameter 17.5
We are a leading Manufacturer, Traders and supplier of galvanized steel sheet. Galvanization is the process of applying a protective zinc coating to steel or iron in order to prevent it from rusting. The term is derived from the name of Italian scientist Luigi Galvani. Galvanized iron (GI) sheets are steel sheets which are basically coated with zinc and include a range of hot dip galvanized and electro-galvanized steel sheets. Zinc weathers at a very slow rate, so the coating generally has a long life. Zinc has a greater electro-negativity than iron and hence provides cathodic (or sacrificial) protection to the steel. This results in the zinc corroding in preference to the steel if the coating is chipped or damaged to expose the base metal. Besides acting as galvanic protector, The other functions of the zinc layer are as follow: To retain the steel intact with its full initial strength. To provide the surface a more pleasing appearance. To increase the life of any suitable organic finishing system applied over it. To protect the steel from corrosive attack in most atmospheres, acting as a continuous and lasting shield between steel and the atmosphere. Features Uniform zinc coating in the range of 60-600 GSM Spangles: Zero / regular / minimized / suppressed Surface finish: Normal spangle, large spangle, small spangle, matte surface With and without tension leveling Passivation: Chromated (Hexavalent / Trivalent) Oiling: 100-1,000 GSM Winding: Controlled / staggered (+/- 5 to +/-15mm) Coil id: 508 / 610 mm Elongation: 16-33%. Dimensions Thickness: 0.18 - 3.2 mm Width: 800 - 1,500 mm Length: Up to 2,500 mm Grades & Standards CQ, DQ, DDQ, EDDQ, HSLA ASTM A653, SS33/37/40/50/60/80, EN 10327, JIS Commercial Steel (CS Types A, B, and C) Forming Steel (FS Types A and B) Deep Drawing Steel (DDS Types A and C) Extra Deep Drawing Steel (EDDS) Structural Steel (SS) further designated by Grades (33,37,40,50,80) High Strength Low Alloy Steel (HSLAS) Supply condition Coil / Slits/ Sheet form
We are a leading Manufacturer, Traders and supplier of galvanized steel sheet. Galvanization is the process of applying a protective zinc coating to steel or iron in order to prevent it from rusting. The term is derived from the name of Italian scientist Luigi Galvani. Galvanized iron (GI) sheets are steel sheets which are basically coated with zinc and include a range of hot dip galvanized and electro-galvanized steel sheets. Zinc weathers at a very slow rate, so the coating generally has a long life. Zinc has a greater electro-negativity than iron and hence provides cathodic (or sacrificial) protection to the steel. This results in the zinc corroding in preference to the steel if the coating is chipped or damaged to expose the base metal. Besides acting as galvanic protector, The other functions of the zinc layer are as follow: To retain the steel intact with its full initial strength. To provide the surface a more pleasing appearance. To increase the life of any suitable organic finishing system applied over it. To protect the steel from corrosive attack in most atmospheres, acting as a continuous and lasting shield between steel and the atmosphere. Features Uniform zinc coating in the range of 60-600 GSM Spangles: Zero / regular / minimized / suppressed Surface finish: Normal spangle, large spangle, small spangle, matte surface With and without tension leveling Passivation: Chromated (Hexavalent / Trivalent) Oiling: 100-1,000 GSM Winding: Controlled / staggered (+/- 5 to +/-15mm) Coil id: 508 / 610 mm Elongation: 16-33%. Dimensions Thickness: 0.18 - 3.2 mm Width: 800 - 1,500 mm Length: Up to 2,500 mm Grades & Standards CQ, DQ, DDQ, EDDQ, HSLA ASTM A653, SS33/37/40/50/60/80, EN 10327, JIS Commercial Steel (CS Types A, B, and C) Forming Steel (FS Types A and B) Deep Drawing Steel (DDS Types A and C) Extra Deep Drawing Steel (EDDS) Structural Steel (SS) further designated by Grades (33,37,40,50,80) High Strength Low Alloy Steel (HSLAS) Supply condition Coil / Slits/ Sheet form
Parameters: Thickness: 0.30 4.00 mm Width: 600- 1500 mm Length: 1000 7000 mm Temper: 1/8 Hard, Hard, Hard, Full Hard, Finish: Dull, Matt, Bright, Mirror Grade: D, DD, EDD, Super EDD Edge: Mill edge, Slit edge CTL: Up to 4500mm with tolerance of +2/-0 mm(Further close tolerance on - request) Surface Finish: Super Bright, Bright, Dull & Matte. (RaValuewith controlled Rmax on request). Grades: Specifications - As per JIS/BIS/ ASTM/EN Standards Low Carbon CRCA Grades Super EDD/EDD/DD/D (SPCX, SPCEN, SPCD, SPCC) non-aging, IF-High Strength steel (IF-HSS), High Strength Low Alloy Steel (HSLA), viz., ST -42, ST-45, ST-52, SAPH-400/41O, Steel for Porcelein Enammeling, Corrosion Resistant Steel, viz., Tin Mill Black Plate (TMBP) Medium & High Carbon CRCA Grades C- 30, C-40,MC -ll, EN - 8, C-55, MC-12, EN- 9 C-62, C-60, C-80, HC-14, EN-42J ELECTRICAL Grades Elec -I, Elec-n, Elec-nI, SemiProcessed Elect. Steel OTHER CRCA Grades Case Hardening Steel- 15Cr3, SAE 1010, SAE 1012 Through Hardening Grades- SAE 1040, SAE 1045, 1055, 1065, 1080, 1541
specification item hot rolled medium and high tensile structural steel â?? is 2062 e250br thickness 1.6mm-20mm width 1000mm-2100mm length 3000mm-18000mm chemical composition of is 2062 e250br plate grade c mn s p si carbon equivalent (ce), max is 2062 e 250 br 0.22 1.50 0.045 0.045 0.40 0.41 mechanical properties of is 2062 e250br plate grade yield strength n/mm2 tensile strength n/mm2 elongation (%) is 2062 e250 br 250 min 410 min 23 plates sheets 1 mm to 300 mm thickness cold rolled, hot rolled
Dimensions Thickness: 0.15-3.2 mm Width: 900 - 1,500 mm Length: Up to 2,500 mm Oiling: 100-1,000 GSM Winding: Controlled / staggered (+/- 5 to +/-15mm) Coil id: 508 / 610 mm Elongation: 16-33%. Grades & Standards CQ, DQ, DDQ, EDDQ, HSLA ASTM A653, SS33/37/40/50/60/80, EN 10327, JIS Commercial Steel (CS Types A, B, and C) Forming Steel (FS Types A and B) Deep Drawing Steel (DDS Types A and C) Extra Deep Drawing Steel (EDDS) Structural Steel (SS) â?? further designated by Grades (33,37,40,50,80) High Strength Low Alloy Steel (HSLAS) Supply condition Coil / Slits/ Sheet form
Dimensions PPGI and PPGL Type: Continuous Coil Color Coating Thickness (MM):0.18 TO 2.00 MM Width (MM):900 TO 1450 MM GSM: 70-250 Gsm Paint Coating thickness: 15-40microns Surface Finishes: Smooth, matt, high gloss, textures, printed Output Coil ID (MM):508mm / 610mm Output Coil OD (MM):1200 mm Output Coil Weight (MT):3-7 MT Type of Painting: EXPOXY,RMP (Regular Modified Polyester), SMP (Silicon Modified Polyester) HDP (High Durable Polyester), SDP (super Durable Polyester) PVDF (Poly Vinylidene Fluoride), PLASTISOL, PUPA/ARS, Anti-Bacterial, Wrinkle Finish /Anti Skidding Self-Cleaning / Anti Dust. Type of Material: HOT DIPPED â?? GALVANIZED steel (ZINC : 60-350 GSM) HOT DIPPED -ALU ZINC (ALUZINC 30-150) Grade:LFQ,SS,SGCC,CS,DX,HX Paint Coating:4-8 Microns primer + 15 TO 35 microns top Coat ( Four Coat System also available â?? Top & Bottom Side with Primer + Paint ) Supply conditions Coil / Sheet/ Slit / corrugated sheets / plain sheets / trapezoidal profiles Applications Construction and infrastructure: Industrial roofing and cladding, cold storage and warehouses, airports, atriums in malls, showrooms, false ceilings, lighting fixture White goods: Refrigerators, display freezers, washing machines, air conditioner wraps Automotive: Bus bodies, railway coaches, luxury coaches
Dimensions Thickness: 0.4-3.2mm (CRCA); 0.15-1.9mm (CRFH) Width: 800-1,625mm Material - Mild Carbon Steel Length - Can be cut to sheets according to requirement Max. Weight - 20MT per coil Grades Extra Deep Drawing steels (EDD, IF) IFHS (350, 400, 440) Bake hardening steel (BH180,220) HSLA (320, 340, 440) Semi-processed electrical steels Steels for enameling CORTEN ASTM: A 1008: DS type A & B, DDS, EDDS, EDDS+ IS: IS 513: D, DD, EDD DIN: DIN 17100: ST 37.3, ST 44.2, ST 44.3, ST 52.3 EN: EN 10268: HSLA 340, HSLA 420,EN 10130: DC 01, 03, 04, 05/06 JIS: G 3141: SPCD, SPCE, SPEN, SPRC 340/ 390,SPFC 340/ 390/ 440 Supply Condition: Coil / Slit / Sheet form Surface textures a. Smooth (plating applications) - suitable for electroplated articles and also for re-rolling when a matt texture is undesirable. A maximum surface roughness of 0,5 micrometers centre line average (CLA) is aimed for. Typical applications are car bumpers, door locks and other electroplated articles. b. Light matt (drawing and pressing applications)- surface roughness of 0.60 - 1,25 micrometers centre line average (CLA) and 100 peaks per inch (PPI) minimum is aimed for. Typical applications are automobile panels. c. Medium matt (drawing and pressing applications)- A surface roughness of 0,8 - 1,6 micrometers centre line average (CLA) and 100 peaks per inch (PPI) minimum is aimed for. Typical applications are drum bodies and ends.
Dimensions Thickness: 1.6 -25mm Width: 900-2,100mm Material - Mild Carbon Steel Max. Weight â?? 22 â?? 25 MT Grades Drawing quality steel: D / DD / EDD Cold rolling grades: IF (Interstitial Free) and High Strength IF Steels Medium carbon / high carbon steels High strength steels: JIS G 3113 SAPH310/370/400/440, JIS G 3134 SPFH-540/590, EN 10149-2 S550MC/S650MC, DP590 Line pipe â?? API X42 to X-80 grades (Sour and Non Sour Applications) Boilers and pressure vessels grades Ship building grades Corrosion resistant steel Re-rolling/ Drawing Grades, Tube and Pipe/ Forming Grades, Structural/ Medium Tensile Tube/ Forming Grades, LPG/ Low Pressure Vessel Grades, HSLA Grades, Medium Carbon Grades, Weather Resistance Grades, Line Pipe Grades, Chequered Plates ASTM (USA) : A 36 A572: Gr 42, Gr 50 IS (INDIA) : IS 2062: E250 Gr A/ B/ C, E350 Gr A/ B/ C DIN (GERMANY) : DIN 17100: ST 37.3, ST 44.2, ST 44.3, ST 52.3 BS (ENGLAND) : BS 4360: 40, 43, 50 EN (EUROPE) : EN 10025: S235, S275, S355 JIS (JAPAN) : G 3106: SM400, SM 490 G 3101: SS400, SS490
0.1ml PCR Plate 4 Tubes and 4 Caps Strips available on 250 Strips pack Compatible with Qiagen Rotor Gene PCR Thermal Cycler
0.1ml 96 well PCR Plate Low Profile Non skirted Pack of 25 plates Compatible with Standard PCR qPCR Machine For More details please contact us
Specifications Type : Finned Material : Copper Thickness : 5-10mm Application : Industrial Color ; Brown Features : Durable, High Strength, Rustproof Grade : Superior
Stainless Steel 7-1/2" Cheeks Blued Steel 5" Broken Mouth
Stainless Steel d-ring style bit with 3" D cheek. Copper 5" broken mouth piece.
Respected Sirs, We Can Supply The Above Cargo As Per The International Laid Standards Within The Brackets Of Price Provided A Minimum Order Qty Of 25000 Tons To 50000 Tons Per Shipment.
Respected Sirs, We Can Supply The Above Cargo As Per The International Laid Standards Within The Brackets Of Price Provided A Minimum Order Qty Of 25000 Tons To 50000 Tons Per Shipment.
Range: 3.17 MM TO 350 MM DIA Stainless Steel : ASTM / ASME SA 276 TP 304 , 304L , 309S , 309H, 310S , 316 , 316L , 316 TI , 317 , 321 , 347 , 410 , 420 , 430 ,431 , 440A ,B & C. , 446 ASTM / ASME SA 479 TP 304 , 304L , 304H, 309S , 309H, 310S , 310H , 316 , 316H , 316L , 316 TI , 317 , 321 , 321H , 347 , 347 H , 410, 430 ,431 & 444. Duplex Steel :ASTM / ASME SA 276 UNS NO. S 31803 , S 32205 , S 32550 , S 32750 , S 32760
Perforated Sheets
We are an Accredited Manufacturers of "HES" Parallel Threaded Rebar couplers in compliance with BS 8110, BS 5900, ACI 318 and BIS 16172:2014 codal specifications. We have a huge clientelle across India and Global for many Renouned Projects.
