V3 Borewell Submersible Pumpset Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP) - Version : Single Phase 160V to 230V, 50Hz, AC Supply - Speed : 2880 RPM - Head Range : 14 Mtr. to 96 Mtr. - Discharge Range : 70 LPM to 15 LPM - Outlet Size in Inch : 1.25" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m�²/sec (max.) - Ph Value : 6.5 to 8.5
V3 Borewell Submersible Pumpset Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP) - Version : Single Phase 160V to 230V, 50Hz, AC Supply - Speed : 2880 RPM - Head Range : 14 Mtr. to 96 Mtr. - Discharge Range : 70 LPM to 15 LPM - Outlet Size in Inch : 1.25" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
Falcon Premium 200 mm (8) Borewell Submersible pumpsets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked in stainless steel stator shell. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - SS-304 Grade investment casting bowl and SS-304 grade impeller in radial flow series - 20 Mtr. Head per stage in radial flow series - Specially designed high performance thrust bearing (SS-420 Tilting pad with carbon plate) to with stand axial thrust loads - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Special designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures services feasibility - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS Pumps are available Specification Direction of Rotation : Counter clockwise from driving end -1ph : Electrically Reversible -3ph - Power Range : 7.5 kW to 75 kW (10 HP to 100 HP) - Version : Three Phase 350 to 415V, 50Hz AC Supply - Thrust Load : 7.5 kW -30 kW -10000 lbs - Speed : 2880 RPM - Head Range : 12 Mtr. To 440 Mtr. - Discharge Range : 2400 LPM to 300 LPM - Outlet Size in Inch : 4.0" & 5.0" - Degree of Protection : IP 58 - Minimum Cooling Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : Star Delta (SD) - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
V7 Borewell Submersible Pumpset Falcon Premium 175 mm (7) Borewell Submersible pumpsets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked in stainless steel stator shell. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Cast iron casting bowl and SS-410 grade impeller in mix flow series - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Special designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures services feasibility - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps Specification - Method of Starting : 3 ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 37.3 kW - Power Range : 11.2 kW to 37.3 kW (15 HP to 50 HP) - Version : Three Phase 350 to 415V, 50Hz AC Supply - Speed : 2880 RPM - Head Range : 18 Mtr. To 650 Mtr. - Discharge Range : 1860 LPM to 55 LPM - Outlet Size in Inch : 2.0 , 2.5 , 3.0 & 4.0 - Degree of Protection : IP 58 - Direction of Rotation : Electrically Reversible -3ph - Thrust Load : 11.2 kW -37.3 kW -8000 lbs - Minimum Cooling Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
V6 Borewell Submersible Pumpset Falcon Premium 150 mm (6) Borewell Submersible Pumpsets are powered by water filled, rewindable submersible Motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow series - 60 feet head per stage in radial flow series - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Additional intermediate bearing in higher stage pumps - Fully SS pump set are available in SS - 304 Grade Specification - Power Range : 2.2 kW to 30 kW (3.0 HP to 40 HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. - Speed : 2900 RPM - Head Range : 12 Mtr. To 600 Mtr. - Discharge Range : 1080 LPM to 170 LPM - Outlet Size in Inch : 2.0, 2.5 , & 3.0 - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW 4.5 kW - 3500 lbs, 5.5 kW - 30 kW - 6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) upto 2.2kW: 3ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 30 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
Falcon Premium 150 mm (6) Borewell Submersible Pumpsets are powered by water filled, rewindable submersible Motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles Salient Features - SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow series - 60 feet head per stage in radial flow series - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Additional intermediate bearing in higher stage pumps - Fully SS pump set are available in SS - 304 Grade Specification - Power Range : 2.2 kW to 30 kW (3.0 HP to 40 HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. - Speed : 2900 RPM - Head Range : 12 Mtr. To 600 Mtr. - Discharge Range : 1080 LPM to 170 LPM - Outlet Size in Inch : 2.0, 2.5 , & 3.0 - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW 4.5 kW - 3500 lbs, 5.5 kW - 30 kW - 6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) upto 2.2kW: 3ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 30 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
V5 Borewell Submersible Pumpset Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are assembled under pressure and rigidly locked in stainless steel stators shell. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series) - 9 Mtr. Head Per Stage In Radial Flow Series. - Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads. - Dynamically balanced roating parts ensure minimum vibration and longer life - Motor Portion covered with corrosion resistant S.S. J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS pumps are available in (GRS - Series) Specification - Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply (Single Phase available in 3 HP to 5 HP) - Speed : 2880 RPM - Head Range : 12 Mtr. To 640 Mtr. - Discharge Range : 690 LPM to 80 LPM - Outlet Size in Inch : 1.5 , 2.0" & 2.5" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW, 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2 kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star Delta (SD) upto 9.3 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are assembled under pressure and rigidly locked in stainless steel stators shell Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series) - 9 Mtr. Head Per Stage In Radial Flow Series. - Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads. - Dynamically balanced roating parts ensure minimum vibration and longer life - Motor Portion covered with corrosion resistant S.S. J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS pumps are available in (GRS - Series) Specification - - Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply (Single Phase available in 3 HP to 5 HP) - Speed : 2880 RPM - Head Range : 12 Mtr. To 640 Mtr. - Discharge Range : 690 LPM to 80 LPM - Outlet Size in Inch : 1.5, 2.0" & 2.5" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW â?? 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2 kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star Delta (SD) upto 9.3 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m²/sec (max.) - Ph Value : 6.5 to 8.5
V4 Borewell Submersible Pumpset Falcon Premium 100 mm (4) Borewell Submersible pump is firmly coupled to a submersible electric motor and Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosive resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification Power Range : 0.37 kW to 4.4 kW (0.50 HP to 6.0 HP) - Version : Single Phase 160V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. Single Phase available in 0.5 HP to 5.0 HP Three Phase available in 1.0 HP to 6.0 HP - Speed : 2880 RPM - Head Range : 10 Mtr. To 340 Mtr. - Discharge Range : 450 LPM to 12 LPM - Outlet Size in Inch : 1.0 , 1.25, 1.5 & 2.0 - Degree of Protection : IP 58 - Direction of Rotation Minimum Cooling : Counter clockwise from driving end -1ph: Electrically Reversible -3ph - Thrust Load : 0.37 kW â?? 0.75 kW- 650 lbs, 1.1 kW -1.5 kW -1000 lbs, 2.2kW, 7.5 kW -1500 lbs. - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR): 3ph Direct Online (D.O.L) - Maximum Starts Per Hour : 20 Times
V9-V10 Borewell Submersible Pumpset Falcon Dlx. 250 mm ( 9 & 10) Borewell Submersible Pumpsets are powered by water filled, rewindable submersibleMotor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under pressureand rigidly locked in stainless steel stator shell. T-Bolt design in all motor ensures rigid construction. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles Salient Features - SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow MRS series 27Mtr head per stage in radial flow series. - FG 250 Cast Iron Bowl with CED Catted and SS-304 Grade Impeller in Mix flow FMC Series 22Mtr head per stage in Mix flow series. - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set. - Dynamically balanced rotating parts ensures minimum vibration and longer life. - Designed for wide voltage fluctuations. - Motor portion covered with corrosive resistance Stainless steel (SS 304) shell. - More durability and hygiene & High operating efficiency. - Specially designed thrust bearing to withstand high axial thrust load. - Extremely hardwearing water lubricated bearing. - Thread type motor construction ensures service feasibility. - Designed for wide voltage operation. - Best alternative for JET & Compressor pump set. - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 55 kW to 112 kW (75 HP to 150HP) - Version : Three Phase 350 to 415V, 50Hz AC Supply - Speed : 2900 RPM - Head Range : 12 mtr. To 300 mtr. - Discharge Range : 3600 LPM to 960 LPM - Outlet Size in Inch : 4.0" & 5.0" - Degree of Protection : IP 58 - Maximum Starts Per Hour : 10 Times
Salient Features Highly efficient 3-phase water filled motor - Easily rewindable - Dynamically balanced design - Extended life with flawless performance - Thrust bearing : Carbon + S.S. material for High thrust load capacity - 100% EC grade copper winding - Presenting world 1st design (design registered 100% fully S.S.-304 investment casting pumps. - Zero maintenance - Superior performance - Sand proof operation - Highly efficient 3-phase water filled motor Product Specification Power Range : 1.0 HP to 20.0 HP Operating Speed : 0 - 2890 RPM Operating Frequency : 0 - 50 Hz Input Solar DC Power Range : 900 Wp, 20000 Wp Input Solar DC Voltage Range : 110 Vmp - 600 Vmp Head Range : 30 Mtr , 220 Mtr Discharge Range : 10000 LPD - 420000 LPD Type of Duty : S1 material of construction - motor Part Grade Body Lock : Spring Steel Stud Ring : M.S. (Zinc Coated) Stator Stamping : CRNGO - M45 Silicon Winding Wire : 100% EC Copper Shaft : SS-420 Rotor Stamping : CRNGO - M45 Silicon Copper Lamination : 100% EC Copper Upper Housing : SS-304 Lower Housing : SS-304 Connection Piece : SS-304 Oil Seal : NBR TB Set : Carbon + SS Base : SS-304 Drain Plug : Brass Couple Sleeve : Stainless Steel Water Bolt : Brass MATERIAL OF CONSTRUCTION PUMP Part Grade Suction : SS-304 Couple : Stainless Steel Couple Counter : SS-304 Rubber Seal : NBR Bush Seal Cover : SS-304 Bowl : SS-304 Impeller : SS-304 Key : SS-410 Bowl Bush : NBR Bush : LTB-4 Middle : SS-304 Cap : NBR Outlet : SS-304
Salient Features Highly efficient 3-Phase Water Filled Motor - 100% EC grade copper winding - Easily Rewindable - Motor Designed with Higher Cooling Effect Ensures Longer Life - Sustainable uniform performance for years - Ensures long life durability - Optimized Hydraulic & Mechanical Design - Improved efficient performance - Excellent output in Low Radiation - Dynamically balanced design - Zero maintenance Product Specification Power Range : 3.0 HP to 10.0 HP Operating Speed : 0 - 2890 RPM Operating Frequency : 0 â?? 50 Hz Input Solar DC Power Range : 3000 Wp, 10000 Wp Input Solar DC Voltage Range : 330 Vmp , 600 Vmp Head Range : 10 Mtr , 50 Mtr Discharge Range : 126000 LPD , 425000 LPD Type of Duty : S1 Material Of Construction Part Grade Oil Seal : Nitrile butyl rubber Motor Shaft : SS - 420 Motor Body : Cast Iron / J4 Motor Bush : LTB-4 / Teflon Thrust bearing assembly : SS - 420 & Carbon Base : Cast Iron Bracket : Cast Iron Flange : Cast Iron Casing : Cast Iron Impeller : Cast Iron
Monoblock pumps - Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features - High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Inbuilt thermal overload protector in al single phase pumpsets upto 2.0 HP - Specially designed for wide voltage operation - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life - Back pull-out design for easy servicing and repair - Double shielded ball bearings, so no need of external lubrication - All Model fitted to Mechanical seal. specification - Power Range : 0.37Kw - 1.5 Kw (0.5 HP - 2.0 HP) - Version : Single Phase, 220-240V, 50Hz AC Supply Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 32 Mtr. - Maximum Flow Rate : 940 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Mechanical Seal - Type of Duty : S1 (Continuous) - Method of Starting : Permanent Split Capacitor (PSC) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 25 X 25, 32 X 25, 40 X 32, 40 X 40, 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 (All size in mm) characteristics of clear cold water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Mechanical Seal : Carbon & Ceramic Motor Shaft : EN-8 Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Plastic
Monoblock Pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. - Mechanical seal is provided as per customers requirement Specification - Power Range : 2.2 Kw - 11.2 Kw (3.0 HP - 15.0 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 65 Mtr. - Maximum Flow Rate : 1450 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 100 X 80 and 100 X 100 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 mÃ?/sec (max.) - Ph Value : 6.5 to 8.5 Material of construction - motor Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminium
Falcon regenerative monoset pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. Salient Features High operating efficiency resulting in lower power consumption. - Good suction lift characteristics. - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. - All Model fitted to Mechanical seal. specification Power Range : 0.37 Kw - 0.75 Kw (0.5 HP - 1.0 HP) - Version : Single Phase, 220-240V, 50Hz AC Supply - Speed : 1440 RPM - Maximum Total Head : 18 Mtr. - Maximum Flow Rate : 4200 LPH - Maximum Suction Lift : 8 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Mechanical Seal - Type of Duty : S1 (Continuous) - Direction of Rotation : Single Phase, Clockwise from driving end - Nominal Pumpset Size (Suction X Delivery) : 25mm X 25mm Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 material Of construction - Motor Part Name Material Mechanical Seal : Carbon & Ceramic Motor Shaft : SS-410 Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : Brass Cooling Fan : Plastic
Monoblock pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. Salient Features High operating efficiency resulting in lower power consumption. - Good suction lift characteristics. - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. specification - Power Range : 1.5 Kw - 5.5 Kw (2.0 HP - 7.5 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 1440 RPM - Maximum Total Head : 12 Mtr. - Maximum Flow Rate : 3160 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase - Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 80 X 80, 100 X 100, 125 X 125, 150 X 150 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminum
Sodium Hydroxide Solution is used in many industries, mostly as a strong chemical base in the manufacture of pulp and paper, textiles, drinking water, soaps and detergents and as a drain cleaner. Appearance: A clear colorless liquid free from foreign matter Relative Density at 40�°C: 1.506 % Sodium Hydroxide [as NaOH]: 48.80% Sodium Hydroxide (On Dry Basis) [as NaOH] : 99.80% Sodium Carbonate [as Na2CO3]: 0.084% Chlorides [as Cl] : 0.004% Sulphate [as SO4] : 0.005% Silicates [as SiO2] : 0.003 % Copper as [as Cu]: 0.08 ppm Manganese [as Mn]: 0.06 ppm Iron [as Fe]: 4.02 ppm Matter insoluble in water: 0.010ppm
Sodium Hydroxide Flakes is used in many industries, mostly as a strong chemical base in the manufacture of pulp and paper, textiles, drinking water, soaps and detergents and as a drain cleaner. Physical Appearance White Flakes, Material shall be free from foreign matter, dirt or other visible impurities Sodium Hydroxide [as NaOH] Min. 99.50 Sodium Carbonate [as Na2CO3] Max. 00.40 Chlorides [as Cl] Max. 00.030 Sulphate [as SO4] Max. 00.030 Silicates [as SiO2] Max. 00.02 Iron [as Fe] Max. 20.00 Copper [as Cu] Max. 02.00 Nickel [as Ni] Max. 02.00 Manganese [as Mn] Max. 01.00 Chlorates & PerChlorate [as NaClO3] Max. 10.00 Matter insoluble in Water. Max. 00.050
Caustic Soda is used in many industries, mostly as a strong chemical base in the manufacture of pulp and paper, textiles, drinking water, soaps and detergents and as a drain cleaner. Physical Appearance White flakes, Material shall be free from foreign matter, dirt or other visible impurities Sodium Hydroxide [as NaOH] Min. 99.50 Sodium Carbonate [as Na2CO3] Max. 00.40 Chlorides [as Cl] Max. 00.030 Sulphate [as SO4] Max. 00.030 Silicates [as SiO2] Max. 00.02 Iron [as Fe] Max. 20.00 Copper [as Cu] Max. 02.00 Nickel [as Ni] Max. 02.00 Manganese [as Mn] Max. 01.00 Chlorates & PerChlorate [as NaClO3] Max. 10.00 Matter insoluble in Water. Max. 00.050
Sodium Hydroxide or Caustic Soda Lye or Solution is used in many industries, mostly as a strong chemical base in the manufacturing of pulp and paper, textiles, drinking water, soaps and detergents and as a drain cleaner. Physical Appearance : A clear colorless liquid, free from foreign matter. Relative Density at 40�°C: 1.485 % min. Sodium Hydroxide [as NaOH] : Min. 48.00 % Sodium Hydroxide (On Dry Basis) [as NaOH] : Min. 99.50% Sodium Carbonate [as Na2CO3]: Max. 00.20% Chlorides [as Cl]: Max. 0.015% Sulphate [as SO4]: Max. 0.015% Silicates [as SiO2] : Max. 00.010% Copper as [as Cu] : Max. 2.00 ppm Manganese [as Mn] : Max. 0.50 ppm Iron [as Fe] : Max 10.00 ppm
