C purlin Sizes are H - 100 to 300 B - 40 to 70 Lip - Up to 20 as standard Thickness - 2.0, 2.15, 3.0 and 3.15 All units are in mm (millimeter)
REFLEX GLASS LIQUID LEVEL INDICATOR Enquiry Now Liquid level indicators are equipped with boron silicate glass, hardened by an accurately controlled heat treatment process. These level indicators are used to display the level of ammonia gas in the system. The liquid level indicators are installed with stop valves equipped with handwheels The liquid chamber is a one piece metal body covered by glass. The light striking the glass in the liquid portion is absorbed by the liquid whereas the light striking the glass in the vapour portion is reflected, making the liquid appear black. Sizes: 12", 18", 24", 30" 36", 42" 48", 54", 60". Gives safe and positive visual indication of liquid level in vessel under high pressure and temperature conditions. Suitable for R717 (Ammonia), HCFC & HFC. In case of glass break, the balls inside the valve stop the refrigeration flow immediately. Tempered boron silicate glass resistant to chemical, thermal and mechanical shocks. Safe working pressure: 400 psig (27 bar). Large chambers for boiling, flashing and surging liquids.
Type SA5 solenoid valves in refrigeration sysytem is the direct acting type & type SA 17, SA 32, SA 42, SA 50 are higher capacity pilot operated Ammonia solenoid valves in refrigeration system & air conditioning applications. SPECIFICATIONS : Refrigerants : R717 (NH3), R22, R134A etc. Temperature of medium -40 C to + 80C Single coil (type KC -3) for all SA series valves. AVAILABLE IN SIZES: 15 mm / 20 mm / 25 mm / 32 mm / 40 mm and 50 mm
MSVA Ammonia Stop Valves are accessible with Standard neck (MSVA-S) in angle way and straightway variants. Ammonia stop valves are specially designed to meet all modern refrigeration application necessities and favorable flow characteristics. These Ammonia Stop valves are very easy to disassemble and repair when required. The Ammonia stop valve cone is intended to ensure perfect sealing and withstand a high pulsation and vibration, which can be present particularly in the discharge line. The MSVA is furnished with internal back seating support/enabling the shaft seal (packing gland) to be replaced while the Ammonia stop valve is still under working condition. Highlights Applicable to R717(Ammonia), R744(CO2), HCFC and HFC. Also utilized in chemical and petrochemical applications. Each valve type is clearly mentioned with type, size and operating range. Quick and simple valve maintenance. It requires less effort to replace the top assembly and no welding is required. Modular Concept Each valve body is available with a number of different sizes and connection types. Possible to transform/convert MSVA-S into any other product of MSVL family (stop/check valves, regulating valve and strainer) by replacing the entire top part. Optional accessories: For frequent operation heavy duty hand wheel can be supplied. For infrequent operation seal Cap can be supplied Available in angleway and straightway forms with Standard neck. The valves and seal caps are prepared for sealing, to avoid operation by unauthorised person, utilizing a seal wire. Internal back seating: Internal metal backseating: -DN 15 - 65 (�½ - 2�½ in.). Internal TEFLON backseating: DN 80 - 200 (3-8 in.). Can be used for flow in both directions. Valve body and bonnet material is low temperature steel as per PED norms. Maximum working pressure: - 754 psi g (52 bar g). Operating temperature range: - 60 to +150C ( 76 to 302F).
Technical Data Introduction Refrigerants Shut off valves are applicable to all common non-flammable refrigerants including R717 and non-corrosive gases/liquids dependent on sealing material compatibility. For further information please see installation instruction for CSVA. These Shut off Valves are used in the Industrial Refrigeration system. Temperature range Standard version : - 46/+150�°C Pressure range shut off valves are designed for max, working pressure CSVA-2 DN-15 to DN-40 : 25 bar (362 psig) CSVA-4 DN 15 to DN 200:40 bar (580 psig) Features Housing Made of special, cold resistant steel. Valve cone Shut off valves cone can be turned on the spindle, thus there will be no friction between the cone and the seat, when the valve is opened and closed. Spindle Made of polished stainless steel so that PTFE and Graphite gaskets are not damaged. Sealing Spindle sealing is done with PTFE and Graphite gaskets assuring 100% sealing. Design Housing Made of special, cold resistant steel. Connections Available with the following connections: - Butt-weld ANSI DN15-40(B 36.10 Schedule 80) Butt-weld ANSI DN 50(B 36.10 Schedule 40) Butt-weld ANSI Socket weld (ANSI B 16.11) - DN 15 - 40 % -1% in.). Valve Cone Spindle Made of polished stainless steel so that PTFE and Graphite gaskets are not damaged. Sealing Spindle sealing is done with PTFE and Graphite gaskets assuring 100% sealing.
HYDRAULIC VALVE
VALVES Ball Valves: (IDF, SMS, TC, DIN, Flange, BSP) Butterfly Valve: (Manual & Pneumatic) Diaphragm & Zero Dead Leg Valves FDV & Flush Bottom Valves Non Return & Plug Valves Sampling & Needle Valve
Features Design as per IS 6137-1983 taper lock design. Gauging practice as per IS 3455-1971. Material En31.
Master Setting Ring gauges are ideals for setting bore measurement instrument. Features: Manufacturing Range : 4.00 mm to 500 mm. Material : OHNS , En 31 Alloy steel. Blank Design as per IS 3485 1983. Gauging practice as per IS 3455 1971. Are ground and precision lapped after a heat treatment process which includes subzero stabilization cycle to ensure dimensional stability. Calibration under standard room temperature at 20 degree celsius on carl zeiss,Horizontal Metro scope which is traceable to National Standards.
Plate Valve, Butterfly Valve, Ball Valve
Brand : Kisna Pneumatics Weight : 150g Base Diameter : 6mm, Width : 79mm Inlet : 1/2 inch BSP, Pipe Thread Type & Size : Rc, 1/2/inch The drain housings are made of first-class aluminium alloy materials through die-casting technology, strong and tight, surface is plastic-sprayed, can resist corrosion by synthetic lubricants of air compressor. Easy to install and clean, no noise and compressed air loss, running safely. Better to clean drain bodies weekly to guarantee better drainage effect and less blockage. Originated from the automatic draining design of the freestyle float ball, KISNA drains are free from electricity, safe, low carbon, environment friendly and really help our end users save costs. Working Principle: Drains are designed with float ball drain system. The outlet of the drain will close and stop draining if the draining buoyance is smaller than the float ballâ??s weight and the pressure from the compressed air. It will have a trickle of drainage if the float weight and pressure are balanced. It will open and start draining if the draining buoyance is greater than the float balls weight and the pressure from the compressed air. It works cyclically according to the buoyance.
Valve Size : 1/2 inch BSP (Inlet),1/2 inch (Outlet) Pressure : 16BAR Brand : Kisna Pneumatics Material : Flame retardant ABS Plastic (Shell Material) Manual test button : Yes( micro switch ) We are presenting an excellent quality assortment of Electronic Auto Drain Valve.
The operation of the gate valve has got it its name. This valve acts like a gate to stop or allow the flow through itself. The valve is either fully closed or fully opened, thus, it faces least pressure drop. These valves are designed for uses related to liquid and gases flow. Here, the valve is opened by lifting the wedge out of the flow path. They are best suitable for hot tapping and pigging and not for throttling purpose.
The globe valve is called so because of its rounded body shape. They are good for regulating flow in a pipeline and ideal for gases control choices. Suraj Steelmet is a known exporter of quality valves and globe valve is one amongst them. Before starting any process we deeply study various factors that can affect its working quality. We offer best balance of requirements and limitations through our services.
It is also a type of check valve that operates because of the difference between upstream & downstream pressures. When the inlet pressure is high then the disc lifts up and the valve allows the fluid to flow to the outlet side. If the downstream or gravity pressure if higher than inlet pressure the disc gets back to its seat. This way reverse flow is blocked. For the smooth process it is important to have durable working disc and this is what we offer. We examine the raw material to be used in our product’s exporting. This results in durable quality production.
Wafer check valve is another type of check valve that allows only unidirectional flow. The advantage of employing check valves is that they automatically block the reverse flow with the change in pressure difference. Wafer check valves have thin design with the swinging disc as the main component. These valves are made to fit in tight spaces so it is desired to get them accurately designed. We offer cut-to-cut exporting and ensures its proper functioning before releasing the consignment.
Check valves are two port valves i.e. two sides opened. Swing check valve allows unidirectional flow. From one side fluid enters and from other it leaves. These are automatic valves that do not require open and close assistance. As they have single directional functionality, thus, automatically prevents backflow or reverse flow. We at Suraj Steelmet maintain inventory of finished swing check valves at best competitive prices.
Butterfly Valves are compact, lightweight and quick opening valves. These are the metal valves ideal for petrochemical and oil industries. These are the most suitable valves in fire sensitive industries because of their lightweight and fire safe nature. As they are small in size, they fit small dimensional needs where space is limited. We at Suraj Steelmet work along specifications entirely to get the required results.
Multiport design system offer great designing flexibility as they can accommodate various ends. Four seats featuring designs are more balanced than 3 seats ball valve. Installing such multiport designs make a lot of tasks easier like for changing the flow plan you can simply remove the valve handle & reposition the ball. Such one piece design can replace more expensive valves. We add great value to the products through our fine exporting unit. Before providing any piping system solution we determine all aspects.
Flush bottom valves are special purpose valves used for draining the unwanted. They are available in various sizes and materials. The material range is given to suit every type of industrial flushing needs. We have an inventory of standard sized flush bottom valves to fulfil instant demands. For special orders we carry out the exporting as per given specifications.
