Find Verified Fiberglass Suppliers, Manufacturers and Wholesalers

FRP-03
Description
Specification Item
Density 2.1g/cm3
Water Absorption <0.05 %
Tensile Strenth 1200 Mpa
Bending Strenth 900 Mpa
Flexural Strength in thermal state 300 Mpa
Water Diffusion Test (12 KV)1min <1 mA
Dye penetration pass after 15mins
characteristics
1. Light weight, high strength, corrosion resistant

FRP is a good corrosion resistant material, and has good resistance to air, water, acid, alkali, salt and many kinds of oils and solvents.Has been used in all aspects of chemical corrosion protection, is replacing carbon steel, stainless steel, wood, nonferrous metal and so on.

2. Good electrical performance

It is an excellent insulating material used to make insulators.High frequency can still protect good dielectric property.Microwave transmittance is good and has been widely used in radome.

3. Good thermal performance

FRP has low thermal conductivity and is 1.25~ 1.67kj /(m�· H �·K) at room temperature. It is only 1/100~1/1000 of metal. FRP is an excellent thermal insulation material.It is an ideal thermal protection and ablative material under the condition of instantaneous super high temperature, which can protect the space vehicle from the erosion of high-speed airflow above 2000â??.

4. Good design ability

(1) according to the needs, flexible design of a variety of structural products, to meet the use of requirements, can make the product has a good integrity.

(2) can be fully selected materials to meet the performance of the product, such as: can be designed to corrosion resistance, resistance to instantaneous high temperature, a direction of the product has special high strength, good dielectric, and so on.

Application: Electrical insulation

Technique:Pultrusion

Material: Fiberglass Yarn and Expoy Resin

Color: Any

Size: S22.5mm,S25mm,S28mm,S32mm,S36mm and length as customer's request.

FRP-04
Description
Epoxy fiber glass tube is high quality material as making high voltage electric devices.

Inner diameter(mm):
24 30 33 36 38 42 46 48 50 52 54 55
56 58 60 63 66 74 75 76 78 80 82 100 105
115 130 140 144 180 1851 94 210 240 245 250 253
Other Inside diameter is available.

Outer diameter and length can be made by customers specific requirements.

Features
Non-Corrosive
2. Dimensionally Stable

3. Lower Life Cycle Cost

4. Flame Retardant

5. Easy to Fabricate and Install

6. Electrically Non-Conductive

7. Lightweight/High Strength

8. Resists Insect Damage

9. High Impact Strength

10. Low Water Absorption

11. Greater Flexural Strength Than Timber

12. Non-Leeching

Physical,mechanical and dielectric property should follow the table below:
Technical requirement
Normal Diameter Thickness Length Tolerance Allowed
inside diameter outside diameter Length
30~70 3~20 500 ±0.3 ±0.3 ±1
70~150 3~20 1000 ±0.5 ±0.5 ±2
150~550 10~100 2800 ±0.5 ±0.2 ±2
Physical and mechanical parameters Physical and mechanical parameters
Index Name Unit Index Index Name Unit Index
Density g/cm3> 1.80 Density g/cm3> 1.80
Water absorption % 0.15 Water absorption % 0.15
Intensity of curvature(circling direction) Mpa 400 Intensity of curvature(circling direction) Mpa 400
Intensity of compress Mpa 98 Intensity of compress Mpa 98
Voltage vitality on parallel layer at normal state for 5min Kv 25 Voltage vitality on parallel layer at normal state for 5min Kv 25
Voltage vitalityon vertical layer in the oil at 90C for 5min MV/m 12 Voltage vitalityon vertical layer in the oil at 90Cfor 5min MV/m 12


Enquire Now
Epoxy fiber glass tube is made by good quality glass fiber steeped into epoxy resin of thermo-stability, which is high quality material as making high voltage electric devices, such as breakers, thimbles, mutual inductors, zinc oxide arresters, etc.

FP-01
Description
Insulated 12mm Rod Pin with a metal point and metal cap, which allows it to be struck with a hammer. Each Insulated Road Pin is flash tested to 10,000V.

Insulated non conductive road pins help reduce the risk of electric shock from buried cables. Manufactured from 12mm fibreglass rod with forged point, allowing it to penetrate a variety of surfaces.

Sizes Available : 12mm x 600-1500mm.

Attachments Available : Metal & Plastic Point & Plastic Hook End & Metal Cap.

FP-02
Description
Insulated 16mm Rod Pin with a metal point and metal cap, which allows it to be struck with a hammer. Each Insulated Road Pin is flash tested to 10,000V.

Insulated non conductive road pins help reduce the risk of electric shock from buried cables. Manufactured from 12mm fibreglass rod with forged point, allowing it to penetrate a variety of surfaces.

Sizes Available : 16mm x 600-1500mm.

We Have Manufacturer Of Coated & Uncoated Frp Rod For Telecom Grade