Description : offering thyristor trigger pulse isolation transformer. Small size, pcb Mountable for coupling a trigger pulse generator to thyristor triac Isolation of small signals from power circuits. Epoxy molded. 4502-1:1 2502-1:1 4503-1:1:1 2503-1:1:1 4504-1:1:1:1 2504-1:1:1:1 4506-2:1 2506-2:1 4507-2:1:1 2507-2:1:1 miniature pulse transformer 4502-1:1 2502-1:1 4503-1:1:1 2503-1:1:1 we also manufacture transformer used in Mobile chargers we also make transformer as per customers requirements If detailed information is provided. 23mm diameter, 18mm height excluding lead height
S64A101-D6 is a vertically polarized broadband dipole blade antenna operating in the frequency band of 20-1200 MHz. and suitable for DF, Navigation & Reconnaissance applications on UAV.
Used in current transformer & power transformer, also used in servo voltage stabilizer & variable auto transformer - dimmer or variac. As per customer requirement.
Remote switch.
Light sensitive switch is a device that is used for automatically switching on and off the street lights garden lighting, passage lighting and doorway lighting etc in accordance with the natural lighting level. The lights connected to the light sensitive switch are turned on automatically in evening when the natural light falls below 15 lux. And lights are switched off in the morning automatically when the light level reaches above 20 lux. Eliminates the need of human operation for switching on and off any external light connected with this system. Saves energy saves electricity , no need to manually switching on and off the light, easy to install and durable. Applications: roadway lighting , building perimeter lighting , outdoor advertising signs , parking lot lighting, garden lighting passage lighting and doorway lighting etc.
Tubular battery for solar and inverter application from 60 ah to 180 ah.
An Electronic Ballast is a device/instrument used to control the amount of current in on electric circuit, Also referred as a control gear, an electronic. If generates high frequency alternative goes about more then 25Khz. High freq. allows to lower the system rating without reducing the luminous flux of the lamps. Also available series of
An Electronic Ballast (Sometimes called control gear) is a device intends to limit the amount of current in an Electronic circuit. An Electronic lamp ballast uses solid state electronic circuitry to provide the proper starting and operating electrical Condition to power fluorescent lamps (FTL).An Electronics ballast dissipates some heal around 90%. GRE’s industrial ballast series heaving special features like EMI/RFI filters, spike protections, high power factors etc. Also available ballast series of
ARN-TS2D is a MEMS based single/dual axis inclinometer module that boasts a low price tag. It is most appropriate for mechanical industry, transportation, heavy vehicle, construction and survey applications. This device returns highly accurate angular data in static conditions and can be a part of lab instrumentation, platform stabilization equipment and oem alignment measuring instruments. Single axis module returns roll and dual axis returns roll and pitch information. 1. Measurement range: 60deg (Pitch), 180deg (Roll) 2. Accuracy in static conditions: 0.1 degrees 3. Size: < 78 mm x 56 mm x 36 mm 4. Weight: < 200 grams. 5. Output rate: 1 to 50 hz configurable 6. Power supply: - +8 to +12 vdc 7. Interface: RS232, RS485 serial digital.
We are mfrg. Different type of solenoid coils DC contactors & contactor coils both AC or DC.
In low Voltage & High Amps D C Contactors with 12V DC to 220 V DC Coil. Available. Single POle,Double Pole & Three Pole.
Acid battery
Details as follows : Rotational-speed range : 20 . 7000 rpm Permanent ambient temperature in the cable area : -40 to + 120C Permanent ambient temperature in the coil area : -40 to + 150C Winding resistance at 20 C 860 : 10 % Inductance at 1 kHz 370mH : 15 % Degree of protection : IP67 Output voltage : 0.200V
Electrical : Output: Analogue or digital Typical Linearity: 2.5% (absolute) 1.0% (independent linearity) Typical Travel: 15mm electrical* / 18mm mechanical* (*application dependent, adaptable to larger or smaller travel requirements) Nominal Index Voltage : Programmable Electrical Limit Maximum : 20 VDC Supply Voltage : 4.5 - 5.5 VDC Typical Current Draw : 12 mA (dependent on program conditions) Maximum Response Time : 600 S Durability : Typical Vibration: 200 hrs.; 3 planes; 20 - 2000 Hz; 40G RMS;-40C -160C. Typical Thermal Shock: 500 cycles, -40C and 160C; 15 sec. transition; 30 min. soak at each temperature Typical Temperature Range: -40C > 160C
Parameter specification : 1 switching capability 10 w (max) 2 switching voltage 100 vdc (max) 3 switching current 0.5 amps (max) 4 contact resistance 1 ohms max 5 dielectric : between terminals 200vdc for 1minute between body & terminal 500vdc for 1minute body & cable insulation 500vdc for 1minute 6 must operating distance 7- 14 mm with tvsc magnet tvsc-mfax-01 7 must release distance 10-25 mm with tvsc magnet tvsc-mfax-01 8 operating temperature 80 deg c max 9 surface temperature 5 deg c max @ ambient 10 ambient temperature -20 to +50 deg c x denotes for high temperature (50 deg c ) 11 IP rating ip 67. 12 sensor dimension 35x19x10 mm 13 Cable 2 core cable with shield 14 Approvals : CE & Atex.
28 watts No ring formation No harmonic distortion 2 yrs warranty Starting 120 v to max 450 v . Please enquire every time.
PE-AOBDV Automatic Oil Breakdown Voltage Testeris a highly precise instrument, which can be applied to measure either the breakdown voltage or also check the withstanding voltage for a predefined time. Usual available automatic test sets only perform the former function, but PE-AOBDV can do both. PE-AOBDV can measure the breakdown voltage repetitively and computes an average reading, for a proper decision making. PE-AOBDV consists of an integrated Oil Cup, HV AC power source. Features - 0-80kV or 0-100kV smooth operation, 5mA trip current - Complete Automatic operation - Non-contact magnetic stirring - Programmable Stir, Hold, and Intermediate Stand times - Programmable voltage ramp rate - Repetitive test sequence and average readings - Digital display output - Integrated thermal Printer - Internal memory for data storage and recall - Included IS 6792, IEC 60156 and GB507-86 test sequences - Programmable test sequences as per requirement. 1 pc - 25 kgs.
2k ohms single turn 0 to 100% .
Transformer.
Electronic control panel for submersible pump for operation of 0.50 hp to 3 hp 1 phase and electrical coustomise panel up to 150 hp in 3 phase. Quality component used in panel for long lastings result and for customer satisfaction Panels are available in diffrent lot size according to hp wise but 1 box contain min. 20 pcs. Weight n dimension are veries according to product specification
