DIRECTIONS FOR USE:
- Shake well before using.
- Keep container closed when not in use.
- Set time is the time required before joint can safely be handled.
- Cure time is the time required before joint can be pressure tested.
1. Cut pipe square with saw or hand cutter. Remove all burrs.
2. Check dry fit of pipe and fitting. Pipe should easily go A1/A3 to A1/A2 way into fitting. If pipe bottoms into fitting it should be very snug.
3. Pipe and Fitting should be free of dirt, grease and other foreign materials. If necessary clean pipe and fitting using RPC-WELD Pipe Cleaner. Primer is highly recommended for 3 and larger diameter installation. Apply liberal coat. Primer will start softening surface of pipe and fitting thus ensuring superior joint.
4. Use applicator supplied with the can or suitable applicator at least A1/A2 the size of the pipe diameter.
5. Apply liberal coat of cement to the pipe (equal to depth of fitting) and adequate coat inside of fitting. Make sure there is no uncoated surface. Avoid puddling of cement, it may weaken the joint.
6. Immediately insert pipe into fitting with twisting motion. Cement should be wet. If it has dried recoat both parts. Use sufficient force to ensure pipe bottoms into fitting.
7. Hold joint together for 30-40 seconds to make sure pipe is not pushed out longer time if temperature is low and for larger pipes.
8. Allow 15 minutes set time before handling the assembly and 2 hours cure time if temperature is below 16 C or 60 F Longer cure time may be required for larger pipe and /or temperature is below 16 C or 60 F.
DIRECTIONS FOR USE:
Shake well before using.
Keep container closed when not in use.
Set time is the time required before joint can safely be handled.
Cure time is the time required before joint can be pressure tested.
1. Cut pipe square with saw or hand cutter. Remove all burrs.
2. Check dry fit of pipe and fitting. Pipe should easily go way into fitting. If pipe bottoms into fitting
it should be very snug.
3. Pipe and Fitting should be free of dirt, grease and other foreign materials. If necessary clean pipe and
fitting using RPC-WELD Pipe Cleaner. Primer is highly recommended for 3 and larger diameter installation.
Apply liberal coat. Primer will start softening surface of pipe and fitting thus ensuring superior joint.
4. Use applicator supplied with the can or suitable applicator at least the size of the pipe diameter
5. Apply liberal coat of cement to the pipe (equal to depth of fitting) and adequate coat inside of fitting.
Make sure there is no uncoated surface. Avoid puddling of cement, it may weaken the joint.
6. Immediately insert pipe into fitting with twisting motion. Cement should be wet. If it has dried recoat both parts.
Use sufficient force to ensure pipe bottoms into fitting.
7. Hold joint together for 30-40 seconds to make sure pipe is not pushed out longer time if temperature is low
and for larger pipes.
8. Allow 15 minutes set time before handling the assembly and 2 hours cure time if temperature is below 16 C or
60 F Longer cure time may be required for larger pipe and /or temperature is below 16 C or 6
RPC-WELD PVC solvent cements have passed the following tests performed according to ASTM Standard D2564
Test Pressure
2 hour Hydrostatic Burst Test 400 psi
2 Hour Lap Shear Test 250 psi
16 Hour Lap Shear Test 500 psi
72 Hour Lap Shear Test 900 psi
DIRECTIONS:
Keep container close when not in use
Set time is the time required before joint can safely be handled.
Cure time is the time required before joint can be pressure tested
1. Cut pipe square with saw or hand cutter. Remove all burrs.
2. Check dry fit of pipe and fitting. Pipe should easily go to way into fitting. If pipe bottoms into fitting
it should be very snug.
3. Pipe and Fitting should be free of dirt, grease and other foreign materials. If necessary clean pipe and
fitting using RPC-WELD Pipe Cleaner. Primer is highly recommended for 3 and larger diameter installation.
Apply liberal coat. Primer will start softening surface of pipe and fitting thus ensuring superior joint.
4. Use applicator supplied with the can or suitable applicator at least the size of the pipe diameter
5. Apply liberal coat of cement to the pipe (equal to depth of fitting) and adequate coat inside of fitting.
Make sure there is no uncoated surface. Avoid puddling of cement, it may weaken the joint.
6. Immediately insert pipe into fitting with twisting motion. Cement should be wet. If it has dried recoat both parts.
Use sufficient force to ensure pipe bottoms into fitting.
7. Hold joint together for 30-40 seconds to make sure pipe is not pushed out longer time if temperature is low
and for larger pipes.
8. Allow 15 minutes set time before handling the assembly and 2 hours cure time if temperature is below 60 F.
Longer cure time may be required for larger pipe and /or if temperature is below 60 F.
Do not test with compressed air.
DESCRIPTION: RPC-WELD CPVC is an orange, heavy bodied, high strength, medium setting CPVC solvent cement for all classes and schedule. This cement is manufactured in the India.
APPLICATION: RPC-WELD CPVC is for use on all grade CPVC pipes and fittings. This cement may be used for potable water, irrigation drain, waste, vent, sewer and conduit. This cement can be used for HOT and COLD water applications.
PROPERTIES AND SPECIFICATIONS:
Color Orange
Appearance Liquid
Set TimeFast Medium
Cure Time Consult ASTM schedule
Exceeds ASTM F- 493 specification
Shelf Life 3 years
Raw Materials from U.S.A
AVAILABILITY:
Size Units/case Units/ master
59 ml 24 192
118 ml 24 144
237 ml 24 96
473 ml 12 48
946 ml 6 24
DESCRIPTION: King PVC Solvent is a clear, medium bodied, high strength, fast setting PVC solvent cement for all classes and schedule. This solvent cement is manufactured in the India.
APPLICATION: King PVC Solvent is for use on PVC pipes and fittings. This cement may be used for upto 4â??â?? pipes and fittings with interference fit for potable water, irrigation, drain, waste, vent, sewer and conduit applications.
PROPERTIES AND SPECIFICATIONS:
Color: Clear
Appearance: Liquid
Set Time: Fast
Cure Time: Consult ASTM schedule
Exceeds: ASTM D2564 specification
Shelf Life: 3 years
Raw Materials from U.S.A
AVAILABILITY:
Size Units / case Units/ master
59 ml 24 192
118 ml 24 144
237 ml 24 96
473 ml 12 48
946 ml 6 24
57157 Construction Materials Suppliers
Short on time? Let Construction Materials sellers contact you.
DESCRIPTION : RPC-WELD PVC Solvent is a clear, heavy bodied, high strength, fast setting PVC solvent cement for all classes and schedule. This solvent cement is manufactured in the India.
APPLICATION : RPC-WELD PVC Solvent is for use on PVC pipes and fittings. This cement may be used for all grade pipes and fittings irrespective of diameter with interference fit for potable water, irrigation, drain, waste, vent, sewer and conduit applications.
PROPERTIES AND SPECIFICATIONS:
Color: Gray
Appearance: Liquid
Set Time: Fast
Cure Time: Consult ASTM schedule
Exceeds: ASTM D2564 specification
Shelf Life: 3 years
Raw Materials from U.S.A
AVAILABILITY:
Size Units / case Units/ master
50 ml 24 192
100 ml 24 144
200 ml 24 96
250 ml 24 96
500 ml 12 48
1000 ml 6 24
DESCRIPTION: RPC-WELD PVC Solvent is a clear, heavy-bodied, high strength, fast setting PVC solvent cement for all classes and schedule. This Solvent cement is manufactured in the India.
APPLICATION: RPC-WELD PVC Solvent is for use on PVC pipes and fittings. This cement may be used for all grade pipes and fittings irrespective of diameter with interference fit for potable water, irrigation, drain, waste, vent, sewer and conduit applications.
PROPERTIES AND SPECIFICATIONS:
Color: Clear
Appearance: Liquid
Set Time: Fast
Cure Time: Consult ASTM schedule
Exceeds: ASTM D2564 specification
Shelf Life: 3 years
Raw Materials from U.S.A
AVAILABILITY:
Size Units / case Units/ master
50 ml 24 192
100 ml 24 144
200 ml 24 96
250 ml 24 96
500 ml 12 48
1000 ml 6 24
DESCRIPTION : RPC-WELD PVC Solvent is a clear, heavy bodied, high strength, fast setting PVC solvent cement for all classes and schedule. This solvent cement is manufactured in the India.
APPLICATION: RPC-WELD PVC Solvent is for use on PVC pipes and fittings. This cement may be used for all grade pipes and fittings irrespective of diameter with interference fit for potable water, irrigation, drain, waste, vent, sewer and conduit applications.
PROPERTIES AND SPECIFICATIONS:
Color: Clear
Appearance: Liquid
Set Time: Fast
Cure Time: Consult ASTM schedule
Exceeds: ASTM D2564 specification
Shelf Life: 3 years
Raw Materials from U.S.A
AVAILABILITY:
Size Units/Case Units/ master
50 ml 24 192
100 ml 24 144
200 ml 24 96
250 ml 24 96
500 ml 12 48
1000 ml 6 24
DESCRIPTION : RPC-WELD PVC Solvent is a clear, heavy bodied, high strength, fast setting PVC solvent cement for all classes and schedule. This solvent cement is manufactured in the India.
APPLICATION: RPC-WELD PVC Solvent is for use on PVC pipes and fittings. This cement may be used for all grade pipes and fittings irrespective of diameter with interference fit for potable water, irrigation, drain, waste, vent, sewer and conduit applications.
PROPERTIES AND SPECIFICATIONS:
Color: Clear
Appearance: Liquid
Set Time: Fast
Cure Time: Consult ASTM schedule
Exceeds: ASTM D2564 specification
Shelf Life: 3 years
Raw Materials from U.S.A
AVAILABILITY:
Size Units / case Units/ master
59 ml 24 192
118 ml 24 144
237 ml 24 96
473 ml 12 48
946 ml 6 24
Metal Aids India a accredited with AN ISO 9001: 2015, 14001: 2015, OHSAS 18001 & PED Certified Company and was established in since 2010. We take the pleasure to introduce ourselves as a largest Manufacture & Exporter of all type of industries products like Seamless & Welded Elbow, Tee, Reducer, Clamp, Cap in different
shape & size (as per client drawing & specification) etc.
Product Specification: UNS 32750 Duplex Elbow
Specification: ASTM / ASME
Size: 1/2\" To 48\"NB & OD (Welded Thk: 1MM to 40MM)
Seamless Thk: Sch10, Sch 30, Sch 40, Sch 60, Sch 80, Sch 160
Type: Elbow (Short & Long Elbow),90 Deg Elbow, 45 Deg Elbow.
Form: Seamless & ERW (Welded)
Grade:
Duplex & Super Duplex: UNS 31803, UNS32205 (F51), UNS 32750
(F 53), UNS 32760 (F 55), UNS 31254 (SMO. 254)
Product Details:
Size 3 inch, 2 inch, 1/4 inch, 1 inch, 3/4 inch, >3inch
Connection Flange, Male, Female, Welded
Material TITANIUM
Application Hydraulic Pipe, Gas Pipe, Structure Pipe, Chemical Fertilizer Pipe
Elbow Bend Angle 90 Degree, 180 Degree, 45 Degree
I Deal In New Only
Metal Aids India, are one of the leading manufactures & suppliers of Titanium Forged Elbow.
Grade:-
Titanium Gr 1, Gr 2, Gr 3, Gr 4, Gr 5.
Dimensions
ANSI/ASME B16.11 & BS3799, etc.
Class:-
2000LBS, 3000LBS, 6000LBS, 9000LBS, etc.
Type:-
Socket Weld (S/W) & SCREWED (SCRD) â?? NPT, BSP, BSPT
Types of Titanium Forged Fittings : â?º Forged Threaded Elbow
â?º Forged Threaded Equal & Unequal Tee
Product Details:
Material SS
Size 3/4 inch, 1 inch, 3 inch, 1/4 inch, >3inch, 2 inch
Connection Welded
Elbow Bend Angle 45 Degree, 180 Degree, 90 Degree
Application Gas Pipe, Structure Pipe, Chemical Fertilizer Pipe
Thickness Sch 20, Sch 40, Sch 80
Country of Origin Made in India
We are stockist & manufacturers of Long radius, short radius Elbow 45 degree, 90 degree, 1D, 2D, 3D in various grades like 304 / 304L / 316 / 316L / 904L / 310 / 317L in both semaless and welded as per customers requirement.
Product Details:
Usage/Application Oil Industry
Size 10-20 inch, 20-30 inch, 1-5 inch, 0-1 inch
Material Standard ANSI B16.5, ASTM A182, ASTM A351, ASTM A105
Rated Pressure (Bar) 2500
Country of Origin Made in India
FLANGE15 NB UP TO 600 NB IN 150 LBS , 300 LBS, 400 LBS , 600 LBS , 900 LBS , 1500 LBS , 2500 LBS / TABLE 2.5 , TABLE 6 , TABLE 10, TABLE 16,TABLE 25 , TABLE 40, TABLE 64, TABLE 160, TABLE 320, TABLE 400FORMSLIP ON , SOCKET WELD , BLIND , LAPPED , SCREWED , WELD NECK , REDUCING , SPECTACLE ,SLIP ON BOSS , PLATE , PLATE BLANK , SCREWED BOSS.
Nickel & Copper Alloy
Nickel Alloy
ASTM / ASME SB 564 UNS 2200 ( NICKEL 200 ) , UNS 4400 (MONEL 400 ) , , UNS 8825 INCONEL (825) , UNS 6600 (INCONEL 600 ) , UNS 6601 ( INCONEL 601 ) , UNS 6625 (INCONEL 625) , UNS 10276 ( HASTELLOY C 276 )ASTM / ASME SB 160 UNS 2201 (NICKEL 201 )ASTM / ASME SB 472 UNS 8020 ( ALLOY 20 / 20 CB 3 )
Copper Alloy
ASTM / ASME SB 61 UNS NO. C 92200 & ASTM / ASME SB 62 UNS NO. C 83600.ASTM / ASME SB 151 UNS NO. 70600 , 71500 , C 70600 ( CU -NI- 90/10) , C 71500 ( CU -NI- 70/30)ASTM / ASME SB 152 UNS NO C 10100 , C 10200 , C 10300 , C 10800 , C 12000, C 12200.
Product Details:
Size 2 inch, 3/4 inch, 1/2 inch, 3 inch, 1 inch
Application Structure Pipe, Chemical Fertilizer Pipe, Gas Pipe
Thread Size as per requirement
Surface Finishing 2B finish
Range 1/4" to 18"
Bend 45 degree, 90 degree, 180 degree
Nominal Diameter 1/4" to 18"
Packaging Type plastic pack or box pack
Port Of Dispatch JNPT
We are exporters of stainless steel socket weld fittings like elbow, tee, reducer, cross, coupling, cap, union etc. in grade F347, F347H, F321, F321H, F310, F309, F317L, F51, F53 etc.
Product Details:
Shape C Channel
Usage/Application Construction
Color Off White
Is It Water Proof Water Proof
I Deal In New Only
Corrosion Proof Yes
Application Oil & Gas Industry, Automobile Industry, Construction, Pharmaceutical / Chemical Industry
Country of Origin Made in India
Stainless Steel Angles, Channels & Flats
Grades 304, 304L, 316, 316L
Size Equal / Unequal Angle Size (mm) Thinckness (mm)
25 4 to 20
25 .00 to 45.00 4 to 25
50 .00 to 60.00 4 to 30
65 .00 to 90.00 5 to 30
100 6 to 30
110.00 to 120.00 10 to 30
125.00 to 150.00 10 to 25
Supply Condition HOT ROLLED, SOLUTION ANNEALED, PICKLED, STRAIGHTENED
LengthAs per required up to 7 mtrs
Product Details
Size 3 inch 2 inch 14 inch 1 inch 34 inch 3inch
Connection Flange Male Female Welded
Material TITANIUM
Application Hydraulic Pipe Gas Pipe Structure Pipe Chemical Fertilizer Pipe
Elbow Bend Angle 90 Degree 180 Degree 45 Degree
I Deal In New Only
Metal Aids India are one of the leading manufactures suppliers of Titanium Forged Elbow
Grade
Titanium Gr 1 Gr 2 Gr 3 Gr 4 Gr 5
Dimensions
ANSIASME B1611 BS3799 etc
Class
2000LBS 3000LBS 6000LBS 9000LBS etc
Type
Socket Weld SW SCREWED SCRD NPT BSP BSPT
Types of Titanium Forged Fittings Forged Threaded Elbow
Forged Threaded Equal Unequal Tee
Product Details:
Material SS
Size 3/4 inch, 1 inch, 3 inch, 1/4 inch, >3inch, 2 inch
Connection Welded
Elbow Bend Angle 45 Degree, 180 Degree, 90 Degree
Application Gas Pipe, Structure Pipe, Chemical Fertilizer Pipe
Thickness Sch 20, Sch 40, Sch 80
Country of Origin Made in India
We are stockist & manufacturers of Long radius, short radius Elbow 45 degree, 90 degree, 1D, 2D, 3D in various grades like 304 / 304L / 316 / 316L / 904L / 310 / 317L in both semaless and welded as per customers requirement.
Product Details:
Usage/Application Oil Industry
Size 10-20 inch, 20-30 inch, 1-5 inch, 0-1 inch
Material Standard ANSI B16.5, ASTM A182, ASTM A351, ASTM A105
Rated Pressure (Bar) 2500
Country of Origin Made in India
FLANGE15 NB UP TO 600 NB IN 150 LBS , 300 LBS, 400 LBS , 600 LBS , 900 LBS , 1500 LBS , 2500 LBS / TABLE 2.5 , TABLE 6 , TABLE 10, TABLE 16,TABLE 25 , TABLE 40, TABLE 64, TABLE 160, TABLE 320, TABLE 400FORMSLIP ON , SOCKET WELD , BLIND , LAPPED , SCREWED , WELD NECK , REDUCING , SPECTACLE ,SLIP ON BOSS , PLATE , PLATE BLANK , SCREWED BOSS.
Nickel & Copper Alloy
Nickel Alloy
ASTM / ASME SB 564 UNS 2200 ( NICKEL 200 ) , UNS 4400 (MONEL 400 ) , , UNS 8825 INCONEL (825) , UNS 6600 (INCONEL 600 ) , UNS 6601 ( INCONEL 601 ) , UNS 6625 (INCONEL 625) , UNS 10276 ( HASTELLOY C 276 )ASTM / ASME SB 160 UNS 2201 (NICKEL 201 )ASTM / ASME SB 472 UNS 8020 ( ALLOY 20 / 20 CB 3 )
Copper Alloy
ASTM / ASME SB 61 UNS NO. C 92200 & ASTM / ASME SB 62 UNS NO. C 83600.ASTM / ASME SB 151 UNS NO. 70600 , 71500 , C 70600 ( CU -NI- 90/10) , C 71500 ( CU -NI- 70/30)ASTM / ASME SB 152 UNS NO C 10100 , C 10200 , C 10300 , C 10800 , C 12000, C 12200.
