Charminar Aerocon Insta panels is a slim and lightweight wall panel consisting of a core of portland cement, binders, silicaceous & micaceous aggregate sandwiched between two fibre reinforced cement sheets. Charminar Aerocon panels are an excellent substitute for plasterboard, plywood, particleboard and brick walls because of their sheer strength coupled with fire & moisture-resistance properties and ease of installation. * lightweight * easy to install * space saving * strong and durable * excellent acoustic barrier * fire resistant * optimum thermal insulation * relocatable.
This motor MCC Panel is exclusive tailor made product & is designed as per requirement of customer. Nos. of motors are started from this panel center & mostly these are DOL or Star- delta Starter motors. All the push buttons & indicators are mounted on panel or remote controlled. Features: Simplex & Duplex pattern Degree of Protection: IP-42 to IP-65 Painting: Powder Coating / Spray Paint / Epoxy Paint Compartmentalized design eliminates risk to maintenance personal Sufficient space for incoming and outgoing cables Provided with buzzer & hooter during emergency Separate Bus bar and cable chambers Motor Control Center shall have hinged door with lockable arrangement Motor Control Center Available with Aluminum / copper bus bar Motor Control Center is suitable for use on 415V, 3 Phase, 4 wire, 50Hz Application: These are widely used for: Protection against electrical Short Circuit, overload and earth fault of the system Control & monitoring of the entire electrical system of an industry / plant Systematic power catering to various load of an electrical system Normally used in Hospitals, Multi-storied buildings, steel industries, cement industry, open â??cast mines, shopping mall etc. We offer the following options and facilities: ASTA certified bus bar systems (50 KA for 1 sec as standard). Separation: Form 4 Type 2 as standard but types 3, 6 and 7 available if required Ingress protection up to IP 65 Wall mounting or floor standing Top, bottom or special cable entry Front or rear cabling access Fixed, plug in or with drawable type Full range of instruments and metering to customers requirements Contactor, soft start and variable speed drives Local or remote control Wired to separate terminal chambers Facilities for thermal imaging Local or remote manual controls Relay or PLC automatic controls Alarm systems Alarm annunciators BMS interface Special control systems to customers requirements
This motor MCC Panel is exclusive tailor made product & is designed as per requirement of customer. Nos. of motors are started from this panel center & mostly these are DOL or Star- delta Starter motors. All the push buttons & indicators are mounted on panel or remote controlled. Features: Simplex & Duplex pattern Degree of Protection: IP-42 to IP-65 Painting: Powder Coating / Spray Paint / Epoxy Paint Compartmentalized design eliminates risk to maintenance personal Sufficient space for incoming and outgoing cables Provided with buzzer & hooter during emergency Separate Bus bar and cable chambers Motor Control Center shall have hinged door with lockable arrangement Motor Control Center Available with Aluminum / copper bus bar Motor Control Center is suitable for use on 415V, 3 Phase, 4 wire, 50Hz Application: These are widely used for: Protection against electrical Short Circuit, overload and earth fault of the system Control & monitoring of the entire electrical system of an industry / plant Systematic power catering to various load of an electrical system Normally used in Hospitals, Multi-storied buildings, steel industries, cement industry, open â??cast mines, shopping mall etc. We offer the following options and facilities: ASTA certified bus bar systems (50 KA for 1 sec as standard). Separation: Form 4 Type 2 as standard but types 3, 6 and 7 available if required Ingress protection up to IP 65 Wall mounting or floor standing Top, bottom or special cable entry Front or rear cabling access Fixed, plug in or with drawable type Full range of instruments and metering to customers requirements Contactor, soft start and variable speed drives Local or remote control Wired to separate terminal chambers Facilities for thermal imaging Local or remote manual controls Relay or PLC automatic controls Alarm systems Alarm annunciators BMS interface Special control systems to customers requirements
This motor MCC Panel is exclusive tailor made product & is designed as per requirement of customer. Nos. of motors are started from this panel center & mostly these are DOL or Star- delta Starter motors. All the push buttons & indicators are mounted on panel or remote controlled. Features: Simplex & Duplex pattern Degree of Protection: IP-42 to IP-65 Painting: Powder Coating / Spray Paint / Epoxy Paint Compartmentalized design eliminates risk to maintenance personal Sufficient space for incoming and outgoing cables Provided with buzzer & hooter during emergency Separate Bus bar and cable chambers Motor Control Center shall have hinged door with lockable arrangement Motor Control Center Available with Aluminum / copper bus bar Motor Control Center is suitable for use on 415V, 3 Phase, 4 wire, 50Hz Application: These are widely used for: Protection against electrical Short Circuit, overload and earth fault of the system Control & monitoring of the entire electrical system of an industry / plant Systematic power catering to various load of an electrical system Normally used in Hospitals, Multi-storied buildings, steel industries, cement industry, open â??cast mines, shopping mall etc. We offer the following options and facilities: ASTA certified bus bar systems (50 KA for 1 sec as standard). Separation: Form 4 Type 2 as standard but types 3, 6 and 7 available if required Ingress protection up to IP 65 Wall mounting or floor standing Top, bottom or special cable entry Front or rear cabling access Fixed, plug in or with drawable type Full range of instruments and metering to customers requirements Contactor, soft start and variable speed drives Local or remote control Wired to separate terminal chambers Facilities for thermal imaging Local or remote manual controls Relay or PLC automatic controls Alarm systems Alarm annunciators BMS interface Special control systems to customers requirements
Aluminum composite panels 1220mm x 2440mm and .4 by .25 x .25 thickness
Electrical panel Industrial automation product panels - control panel, mcc panels, instrumentation panels, desk panels
We manufacture and supply PCC Panel that is used to control the power supplied to motors and transformers. Our PCC panel is a power distribution board that can be used to control the power supplied to HT motors, MCC panels and transformers who play vital role in any electrical control system. They find application in refineries, chemical plants, dairies, refrigeration plant, pharmaceuticals and plastic industries. Features: Made of high quality materials and components Error-free performance High efficiency
With an aim to stand tall on the expectations of our esteemed clients, we are Operator Panels actively committed towards offering a wide assortment of quality assured HMI. These HMI Operator Panels are precisely manufactured at our sound and facility-enriched manufacturing unit using high grade raw material and cutting edge technology. Further, we test these panels against various quality parameters to ensure their durability and finish. Perfectly designed, these HMIsare offered at industry competent prices. Features: Trouble free operation Easy synchronization Withstand fluctuation of voltage
We manufacture and supply PCC Panel that is used to control the power supplied to motors and transformers. Our PCC panel is a power distribution board that can be used to control the power supplied to HT motors, MCC panels and transformers who play vital role in any electrical control system. They find application in refineries, chemical plants, dairies, refrigeration plant, pharmaceuticals and plastic industries. Features: Made of high quality materials and components Error-free performance High efficiency
We manufacture and supply PCC Panel that is used to control the power supplied to motors and transformers. Our PCC panel is a power distribution board that can be used to control the power supplied to HT motors, MCC panels and transformers who play vital role in any electrical control system. They find application in refineries, chemical plants, dairies, refrigeration plant, pharmaceuticals and plastic industries. Features: Made of high quality materials and components Error-free performance High efficiency
We are engaged in offering Drive Automation Control Panels that is based on advanced technology and find application in different industries. This control panel is designed to operate on its own i.e. give command out put to drive valves/motors/ alarm etc in industrial process based on the feed back given by different process Instrument. Our range of control panel is in compliance with set industry standards. Features: Robust structure Cabinet available in various material Digitally controlled system
With the help of our experienced professionals, we are offering superior quality Relay Logic Control Panel. This Relay Logic Control Panel is huge demand in the market due to high quality and durability. These products are available at competitive rates. Features: Repetitive operations Time-driven operations Event-driven operations High-speed control
We specialize in manufacturing and supplying a wide range of PLC Automation Control Panels. Our product is available in both customized designs and standard designs as per the exact requirements of clients. This control panel is engineered as per world class standards and using best available technologies. It is extensively recommended by clients owing to its less maintenance cost and longer functional life. Features: Customized designs Low maintenance Availability in various specifications Other Information: Pay Mode Terms: L/C (Letter of Credit) Minimum Order Quantity: 1 Enter Unit Type Delivery Time: Within a month
