Ring joint metallic gasket Metal ring gasket is by smithing, heat treatment and mechanical processing. It is suitable for oil or gas pipe flange, pressure vessel, high speed joint face, valve with high temperature and high pressure. It has good sealing performance even when the pressure and temperature is not stable.The typical style r are divided into ellipse style and octagonal style according to its cross section. The standard style r gasket is made conform to the api 6a & asme b16, 20 standard, can bear 10000psi pressure at most. The octagonal style and ellipse style can be interchanged in flange with trapezum groove. Style rx is an improvement of style r in pressure resistant. It is a standard ring gasket suitable for all the flange sealing which is suitable for style r. Style by is another item with a high pressure resistant up to 15000psi. We have some different material and style which can correspond to different design and operation demand please see the following table for the reference of material characteristic. 56sheets/packing
Spiral wound gasket Spiral wound gasket is the best in the compression resilient in all the half-metal seal gasket, which is made by the metal hoop band and different kinds of packing material. We can make its structure density according to the demand of different locking force, and we use the inner and outer circle to control the maximum compact degree. So it can be well suit the rough flange face, especially suit the situation of unbalance load, loose of joint force, temperature and pressure change periodically , concussion and shock. It is used in flange joint of valve, pump, heat exchanger, tank, and handhole. It is widely used in the fields like petrochemical industry, machine, electric power, metallurgy, ship-building, medicine, atomic energe, space navigation. We made spiral wound gasket conform to different standards, for example, asmi, bs, jis, din and several other criterion used in china. 100x40x1mm
Spiral wound gasket is the best in the compression resilient in all the half-metal seal gasket, which is made by the metal hoop band and different kinds of packing material. We can make its structure density according to the demand of different locking force, and we use the inner and outer circle to control the maximum compact degree. So it can be well suit the rough flange face, especially suit the situation of unbalance load, loose of joint force, temperature and pressure change periodically , concussion and shock. It is used in flange joint of valve, pump, heat exchanger, tank, and handhole. It is widely used in the fields like petrochemical industry, machine, electric power, metallurgy, ship-building, medicine, atomic energe, space navigation. We made spiral wound gasket conform to different standards, for example, asmi, bs, jis, din and several other criterion used in china. 100x40x1mm
Non-asbestos joint sheet At1600 series---the products made of asbestos are rejected step-by-step when people demanding more and more on the health and environment-protection.Expandable teflon and flexible graphite are used much more widely than ever in modern industry. Although they are gradually replace the asbestos gasket, they cannot do it completely because they have some defect. So the non-asbestos sheet become the best replacement of asbestos planking. The non-asbestos sheet which is made of aramid fiber, inorganic fiber, synthetic rubber etc under high temperature and high pressure. The nonasbestos material is widely used in the joint part of tubing, valve, heat exchanger, pressure container in refinery, chemical plant, power plant, boatyard, pipework. 10000x1000x1mm/volume
Gasket Manufacturers and suppliers of head gaskets for evenger, kia pride, mercedes benz, paykan, willys.We also manufacture plain washers, turning components, spl. Fasteners, long threaded bars, spokes.Above that we also deal in leather animals and home furnishing items bed sheets, pillow covers, cushion covers, duvet covers, 100%pure vigin wool blankets. 100 pcs
The Spiral Wound Gaskets can be used to seal fluid pressure up to 250 bar cryogrnices temperature as low as -2000C and up to elevated temperature of 10000C Products are widely used in the oil, gas, petrochemical process and engineering industries. We can produce according to ANSI B16.5, MSS SP-44, API605, DIN, JIS, JPI, BS1560
SPIRAL WOUND GASKET The spiral wound gasket is suitable for use across a wide pressure range and is therefore virtually applicable. The spiral wound gasket can be used to seal fluid pressures up to 250 bar and cryogenic temperatures as low 200C and up to elevated temperatures 550C. Due to its sturdy design the spiral wound gasket is simple to install without causing damage (although extra care should be taken during transportation and installation of large diameter gasket without guide rings). The outer guide ring serves to locate the spiral element centrally on the flange faces and prevent blow-out. By combining different winding materials and metals the gasket can be tailored to a wide variety of operating conditions. Due to its non-adhesive character the gasket is easy to remove after service. The gasket does not cause damage to the flange faces. BENEFITS OF THE CENTRING RING The spiral wound gasket outer centering ring provides the following benefits: Optimum location between the bolts. Protection of the spiral wound element. Additional security against gasket blow-out. Acts as compression limiter preventing overloading and over compression of the spiral wound element. Prevents radial-flow of soft fillers, such as P.T.F.E. For these reasons it is preferable to use spiral wound gasket with outer centering rings. On the outer ring is marked with nominal size, pressure class, standard and materials. BENEFITS OF THE INNER RING The spiral gasket inner ring provides the following benefits: Prevents radial-flow of soft fillers, such as P.T.F.E. Reduces turbulence-minimizing flow resistance and crevice corrosion. Acts as a heat shield when the spiral wound gasket is subjected to high temperatures. Inner and outer rings are particularly recommended for use on spiral wound gaskets exceeding class 600lbs, but specifically recommended for high temperatures and pressures to optimize the operational reliability of the spiral wound sealing element. MATERIAL SELECTION Material selected for the inner ring and winding metal is usually the same as the flange metal, in order to prevent corrosion and differential expansion problems. The outer centering ring is generally manufactured from carbon steel with an anti- corrosion treatment; however, the ring may also be manufactured in the same metal as the flange to prevent corrosion problems.
Fitment: 84-99 EVO ONE -PIECE LOWER ROCBBR HOUSING GASKET STEEL
Fitment: HusqvarnaK750, K760 Only fits K760 models built before 2013 GHS part number - 2365 OEM part number - 5063853-01, 5063853-04, 5813574-02
Similar fits No. 48-308 / 611812 Fits 2001 - 2004 Polaris Genesis I 2001 - 2002 Polaris Genesis/Pro1200 2003 - 2004 Polaris MSX140 2001 - 2002 Polaris Virage TX 2001 - 2002 Polaris Virage TXI Product link: https://www.sineramarine.cc/buy/main_products.php?pid=543&mt=1 We are a manufacturer for Aftermarket supplier for stern drive, snowmobile, PWC, jet ski and ATV spare parts selling worldwide. For more information and price, please feel free to contact us.
Similar fits No. 48-308 / 611812 Fits 2001 - 2004 Polaris Genesis I 2001 - 2002 Polaris Genesis/Pro1200 2003 - 2004 Polaris MSX140 2001 - 2002 Polaris Virage TX 2001 - 2002 Polaris Virage TXI Product link: https://www.sineramarine.cc/buy/main_products.php?pid=543&mt=1 We are a manufacturer for Aftermarket supplier for stern drive, snowmobile, PWC, jet ski and ATV spare parts selling worldwide. For more information and price, please feel free to contact us.
Thickness- 2.5 mm,3.5mm,4.5 mm & 6.5mm Filler Material - Graphite, PTFE, Non-Asbestos fiber, CAF Material -SS 304, SS 306, Nickel Type-Gasket Use- Industrial
Cylinder Head Gasket For " BMW " Part Number : 11127567764
Cylinder Head Gasket For " BMW " Part Number : 11127506983
Cylinder Head Gasket Right For " Mercedes-Benz " Part Number : A1560160020
Automatic Transmission Oil Pan Gasket For " Audi & Volkswagen " Part Number : 09L321371A
GEAR , TRANSMISSION PAN GASKET FOR " Audi & Volkswagen " Part Number : 09E321371
ELRING SEAL, AUTOMATIC TRANSMISSION OIL SUMP, Engine Oil Gasket FOR " Audi & Volkswagen " Part Number : 0AT321371
Cylinder Head Left Gasket For " Mercedes-Benz " Part Number : A1560160420
Hydraulic filter, Automatic transmission, Seal, Automatic transmission oil pan, Hydraulic filter For " Audi & Volkswagen " Part Number : 09K321370
