Timothy or mixed medow hay bales, square or round for horses.
GEA Varitherm VT-20 Plate Heat exchanger is made of several Varitherm-design stainless steel plates which are combined to form one effective heat transfer unit. Within each plate package the heat exchanger plates support each other at the metal-on-metal profile cross points, which ensure the stable behavior of the plate gap. The plate gasket has so called glue less sealing system. VT-20 is specially designed for cooling and heating of fluids with particle content up to a particle size of 2 mm as well as condensation of vapors, gas cooling and gas dehumidifying. This unit is in good operational condition. Manufacturer: GEA Ecoflex GmbH Type: VT 20 BC-12 Serial no: 170/12982 Year of manufacture: 2000 Frame material: Stainless Steel AISI 4571 Plate material: Stainless Steel Max. operating pressure: 16 Bars Max. operating temp. 100 C Max flow volume: 90 m3/h Width: 337 mm Length: 999 mm. Manufacturer: GEA Ecoflex GmbH Type: VT 20 BC-12 Serial no: 170/12982 Year of manufacture: 2000 Frame material: Stainless Steel AISI 4571 Plate material: Stainless Steel Max. operating pressure: 16 Bars Max. operating temp. 100 C Max flow volume: 90 m3/h Width (plates) 337 mm Length (plates): 1370 mm.
Good condition filtration press made ny German MSE Filterpress GmbH in year 1997. The press has 33 plates of size 630 x 630 mm, cace thickness 25 mm. Includes own hydraulic system and control cabinet. The equipment is manufactured by German MSE Filterpress GmbH, year 1997. Manufacturer’s type KFP 630-40-25K-MPN+DLMP. Structure is made on normal construction steel, plate size is 630 x 630 mm. The filter plates are pressed with single acting hydraulic cylinder with inbuilt hydraulic pump-motor. Product is fed in a central sludge feed inlet with flange connection and each pressing unit has its own outlet for the liquid filtrate which is them collected in one outlet channel. The cake will be disposed under the press. The unit has its own control panel attached to the equipment. Technical data: Manufacturer: MSE Filtterpress GmbH Year of manufacture: 1997 Manufacturers type: KFP 630-40-25K-MPN+DLMP Plate size: 630 x 630 mm Number of plates: 33 Cake thickness: 25 mm Hydraulic pressure: 380 bar max Filtration pressure: 15 bar.
Compressors units (totally 4 pcs) are built by York Sabroe in 2002 and 2003 and they operate with R22 refrigerant. Two identical SAB 128 HF screw compressor units are built on a common base frame with an integrated horizontally mounted oil separators, oil circulation pumps and local operating panels. Common (for two compressors) plate type Freon / Glycol evaporator, internal glycol circulating pump and one large Freon buffer tank is also build on the same base frame. Delivery includes also evaporative condenser and LV / Control cabinet and external glycol circulating pump. Above described 2 x SAB 128 HF packages we have two for sale, one made in year 2002 and the other year 2003. Both packages are still installed and can be tested in mutually agreed time. Units have been in operation approx 6 years and 5 years and they are in very good condition. Technical data Number of compressors - 4 pcs Compressor type - SAB 128 HF Refrigerant - R 22 Cooling capacity - 4 x 379 kW ( 0 /+40C) Swept volume - 4 x 454 m3/h Electric drives (compressor) 4 x 110 kW - 400/690 V 50Hz (also suitable for 60Hz) Freon buffer tank -2 x 1650 liters Plate evaporators - Alfa-Laval M10-BW FGR Evaporative condensers - 2 x BAC VXC 116 Closed Circuit Condenser fans - 1 x 17 kW and 1 x 4 kW for each Condenser circulating pumps- 2 x Grundfors LP80 - 25/133 Glycol pumps - 2 x Grundfors LP 80 - 25/133 2 x Hilge Mahana 65-160
The main description of the plant equipmet is: 1. Brew House Make & Capacity: Steinecker1995 -1999 5 brews/d, 450-500 hl/brew. for 7000 kg malt, 3850 Raw grain Cast-out quantity: 500 hl, 16,5° Plato 8 Brews/ 24 hours, annual capacity 0.85 Mhl Controls are based on Siemens S5 and S7 PCS with, Botec Control system, PC Windows 2000 (Steinecker) Laboratory yield = 97.1% (2.1.09 – 28.5.09, 837 brews) The Brewhouse was installed in 1996 - 1999 by Steinecker to a high standard of control and automation and it contains the following main equipment: Wet Conditioning Mill, capacity 20 tons/hour and it is fully overhauled 2008 Configuration, main characteristics: 1 wet mill plant: 20 t/h 1 mash tun kettle plant: V=550 hl 1 lauter tun plant: D=7200mm 1 weak wort tank: V=155 hl 1 pre run vessel: V=640 hl 1 CIP- water distributor brew/whirpool kettle hot wort max. 520 hl (1 brew / 5 hours) wort cooling 400 hl/h, 10°C - Mash Kettle, a jacketed vessel 550 hl - Enzyme Dosing pot and pump - Lauter Tun complete with spent grain tank and Pondorff pneumatic grains transfer. Tun capacity 814 Hl and diameter 7200 mm, Solids capacity of 7000 kg malt and 3850 kg raw grain. Complete with internal rakes and scrapers - Pre Run Vessel complete with internal heater , volume 640 hl - Wort Boiler/ Whirlpool, gross volume 757 hl net 520 hl - Wort Cooler with aeration – GEA supplied plate heat exchanger (YOM 1990) – rated at 450 Hl/hr cooling the wort from 95oC down to less than 10oC. Cooling achieved with brewing water and then chilled water. Aeration achieved by use of a sintered disc and static mixers, and controlled manually using mass flow meters - 2 Hop Pellet Tanks - 2 Hop Oil Tanks - Brewhouse Weak Wort Tank, volume 150 hl - Alfa-Laval Decanter, year 2008, capacity 100 hl / h - 2 Weak Wort Tanks, volume approx 80 hl each - Gypsum Tank, volume approx 40 hl - Wet starch tank – volume 100 hl - Spent Grains Silo - Spent Grains Drying System - Bulk Acid tank – plastic tank with integral bund and dosing pumps
R -STEEL, Fastening products are standard steel components embedded in concrete for connecting steel or precast elements by welding. It develops its load resistance by virtue of anchorage provided by studs or bars welded to steel plate. Fastening systems are categorized into the following types based on their area of application and load carrying capacities. SBKL Fastening Plates Plate thickness 8-15 mm Headed studs.Steel For lighter loads. KL Fastening Plates Plate thickness 8-15 mm Ribbed bars as anchors. For dynamic anchoring. JRL Fastening Plates Plate thickness 25-30 mm Ribbed bars as anchors. For heavy loads. RKL Fastening Plates Plate thickness 10-25 mm Available for customized lengths (ex. 2000 - 6000 mm) Headed Studs For heavy loads. Salient Features - Load capacities ranging from 0.5 to 12.5 Tons - All plates available in steel, stainless steel, and acid resistant materials. - Both Galvanized as well as Epoxy coated are available. - Fastening plates with Anchors S235JR+AR have a 40 �m protective painting on top surface and on sides. - Plates 1.4301 and 1.4401 have no surface coating. - Resistances are calculated for concrete C25/30. - Resistances take into account the manufacturing tolerances and an assembly tolerance of ± 15 mm. - Dimensions for dynamic loads must be done separately. - All plain steel plates come with painting to prevent rusting at the warehouse and at site. - Fastening plates are marked with Inspecta Sertifiointi Oy control mark, the emblem of R-Group Finland Oy, the type of the fastening plate and production date. - R-STEEL, fastening plates are tested, approved and, in terms of load resistance, designed according to Eurocodes. - R-STEEL, also provides tailor made fastening products as per project requirements.
R-steel threaded lifting devices including several options as wire loops, wire loops equipped with a pressure plate and full metallic lifting devices, are designed to transport and erect precast units and elements. R-steel lifting devices have been designed and tested according to european quality standards to ensure safe precasting and lifting. - wire loops are manufactured of high-quality steel wire which are more suitable for on-site high loads such as beams. It can be equipped with a pressure plate for different lifting angles. - full metallic lifting devices equipped with pressure plate are designed for the lifting of 0 - 90 angles. The free turning swivel can also be used for turning precast elements. - all threaded lifting devices are easy to install and can be recessed if required, they can be used with all sizes of threaded inner socket anchors. - inner socket anchors are provided separately from lifting devices and it's highly recommended to use co-ordinated lifting system units for the safety of your precast site. Nailing plates, socket magnets, and plastic caps are also available. - tailor made solutions are also available.
R-steel, offers a comprehensive range of high quality lifting systems designed for safe lifting and transportation of various types of precast elements. Your selection may be based upon technical or economic requirement or due to already owned/available lifting equipment. R-steel, threaded lifting systems system consists of threaded anchors their lifting devices and other accessories. * salient features - load capacities ranging from 0.5 to 12.5 tons. - used for lifting all kind of precast elements. - used for lifting angle from 0 to 90 degrees. - easy to install and can also be recessed if required. - ce marking. * products: - r-lifting anchor - are threaded socket with headed stud for anchorage. - rls crosshole anchors - are threaded socket with hole for ribbed steel bar for anchorage. - rpas plate anchor - are steel tube with inner thread welded to a flat steel plate for anchorage. - rta, rwtl and rwts anchors - are threaded socket with straight/ wavy ribbed bar for anchorage. - wire loop lifting device - used for lifting angle between 0, , and 45, , . - wire loop lifting device equipped with pressure plate - used for lifting angle between 0, , and 90. - full metallic lifting device equipped with pressure plate for lifting angle between 0, , and 90. - nailing plates, socket magnets and plastic caps are also available. - custom made solutions are also available
Precast Concrete Magnets - Wire Loop Box Magnets - Fastening Plate Magnets L115 x 115 x 5 Steel Instrument box magnet - Electrical tube Magnets - Low& High Socket Insert Magnets - Distribution Box Magnets Diameter 94 x 26.5 & 75 x 29.8 - Shutter Magnets 300kg - 600kg - 1000kg
Hollow Core Slab Supports steel parts manufactured by R-Steel R Group Finland Oy under European quality standards. ROK Slab Supports Designed for support of HCS slab end at holes in HCS slab structure. The R-STEEL® ROK is a great technical solution to support hollow-core slabs(HCS) and make openings into hollow-core slab floors. ROK consists of an L-shaped steel front plate welded together with side plates. It transfers HCS slab end support reaction to adjacent HCS slabs or walls in both installations of HCS slabs and in the �nal situation. ROK support (together with seam grout) acts as support structure until fire resistance class R 60 without separate fire protection. Available in several standard models with the maximum width of opening up to 240 cm. RLK and RLKP Slab Supports Steel parts designed for support of precast massive concrete slabs. R-STEEL® RLK and RLKP slab support transfers the slab support reaction to supporting walls or other structures. RLK slab support consists of two square structural hollow section steel tubes that are installed one inside another and ribbed steel bond bars, which are welded to the outer tube. RLKP slab support consists of two square structural hollow section steel tubes that are installed one inside another and studded steel bars, which are welded to the outer tube. Structural hollow section steel tube with the larger section dimensions is installed to the concrete slab before concrete is cast. The end of the steel tube closer to slab edge is pressed against the mold and the other ends is closed with a welded steel plate, which prevents concrete from entering the steel tube during casting. During the installation of the precast slab the smaller tube is inserted in to the larger tube. Smaller tube is left protruding from the slab for approximately 95mm and acts as a cantilever support.
- r-steel, rpp& rpp-e anchor bolts are fastening elements used to connect precast building components such as beams, columns and walls to adjoining elements or foundations. Rpp bolts for moderate loads and rpp-e bolts are used for high loads. - r-steel, rpk-n2/ rpk-e2 column shoes are fastening components used with anchor bolts to create moment resisting connections for precast columns to foundations or linking columns together, - r-steel, rsk-n, rsk-e wall shoes fastening components create tension resisting connections across joints between two precast wall elements or between precast wall element and a site cast structure. - the advantages of this connection system are rapid assembly of the columns eliminating the need for temporary bracing during installation. - additional ral washer plates are supplied with the associated wall shoes to form the connection to the matching base bolts. - these r-steel, components are used in combination to prevent any fit issues from different suppliers
R-Steel® Wire Loops and Boxes manufactured by R-Group Finland Oy are steel parts consisting of a high strength steel wire and a steel box. R-Steel® Wire Loop boxes are very easy to use on site, with proven no tool tear off tape that releases the flexible loops. Our wire loop box range includes: Single wire loop boxes and Double wire loop boxes. Highly effe�cient product available for both precast and cast in situ structure. It is mainly used in the connection of slabs, walls and columns. Quality control of the wire rope loops is done according to the requirements of the Finnish Code of Building Regulations and the instructions according to the quality and environment system of the R-Group Finland Oy (ISO9001 and ISO 14001). R-Group Finland Oy has a quality control contract with Inspecta Sertifiointi Oy. The steel box and the wire rope are zinc coated. Zinced products are passivized with min. 1 month of storage. R-Steel Loop is a flexible wire rope is bent to loop and held together by compression sleeve. R-Steel® Loop may be used e.g. to tie concrete wall elements to the building frame with ribbed steel bars installed through the wire rope loop. The wire boxes have the advantage of ease of casting and protection of the loop, however the R-Steel® loops can be used in thinner panels and can also be used for lifting. Single Wire Loop Boxes For Single Boxes available standard wire lengths of 60 mm, 80 mm, 100 mm, 120 mm and 140 mm. Double Wire Loop Boxes Double Wire Loop Box offers unique solution for joining double walls to precast elements. Design resistances can be achieved in all directions. Wire lenghts of 80 mm and 100 mm are available for double wire loop. Thickness of the steel plate of the box is 0,7 mm, according to SFS-EN 12385.
