Find Verified Power Saving Devices Suppliers, Manufacturers and Wholesalers

The recovery plant is specially designed to recover CO2 from fermentation processes at breweries. This complete CO2 plant was installed in 2001 and it has nominal CO2 removal capacity of 1000 kg/h. The plant has Siemens S 7 control system where operation is carried our via a large 12 " color screen panel with Windows CE operating system. This is a complete CO2 recovery plant and final delivery scope depends on buyers needs. The plant has been in operation only approx 5 years and is still installed and in very good condition. The carbon dioxide plants was designed by Danish Union Engineering (www.union.dk ) and the delivery includes following main components:

- 1 Scrubber for gas flushing
- 2 Foam catcher vessels
- CO2 collection, inflammable
- 2 Mehrer TZW 70 CO2 compressors
- 2 Carbon filters
- 2 Dehydrators
- CO2 Liquefier
- CO2 Storage Tank
- 2 Cooling compressors GEA Grasso GD-3 for R717
- Air cooled condenser for NH2 compressors
- Alarm center for CO2 and NH3 concentration
- Station for 40 kg CO2 still tank filling
- CO2 pumping station from a truck to the factory
- CO2 purification tester
- Steam heated evaporator for liquid CO2

Detailed technical information available for serious buyers

Manufacturer pompetravaini italy, made in year 2002. Vacuum pump is two staged rotating pump with externally located, grease lubricated bearings. Pump is liquid ring type designed for water sealed operation. The impeller and shaft are made of stainless steel (aisi 316), cast iron casing and manifold normal steel. The shaft is sealed with double mechanical seal. Pump is provided with connections for service water and draining. Pump includes also anticavitation valve. Pump is dismantled from its base frame but the delivery includes original electric motor eex classified abb hyr 200m lb 4 30 kw, 1476 rpm, year 1995. The equipment will be supplied loose - not as a skid.

Technical data:trch 80 - 540/c2/ra
Max suction pressure:25 mbar (till 300mbar)
Max capacity:540 m3/h (min 400 m3/h)
Flanges:80 mm
Rotation speed:1500 rpm
Power requirement:30 kw at 1500 rpm
Year made:2002
Condition:fully operational

Rotary Lube Blower / Vacuum compressor KAESER EB 420 C û 38 m3/min, 53 kPa

There are two identical sets of oil-free, 2 lobe rotary blowers, made by Germand Kaeser Kompressoren GmbH in year 2005 with accessories. Manufactures type is Kaeser ED 420 Compact Omega Pluss 53 and accessories include a control cabinet with two inverters and programmable Kaeser Start Control STC 30 unit, totally 6 preliminary intake air filters and 3 final air intake filters with their steel supports. The rotary blower units have removable sound enclose for noise insulation. Operation of the equipment was stopped in year 2007, total running hours approx 7000 and therefore they are in excellent operational condition. In addition, we can offer you service maintenance by the manufacturer at separate cost.

This equipment is suitable for demanding dust collection and pneumatic transportation of various products due to oil free operation. For pneumatic transport application some changes in filters and other parts are needed.
The rotary lobe has two blower shafts with high efficiency Omega profile in a blower block. The rotary lobe and the block have a very small distance and they are not touching each other's and therefore there is no need for lubrication oil. The rotors are driven by high efficiency electric motor via belt connection and they both are installed on the same base frame. . The inlet and discharge silencers are designed to be effective at all frequencies and are eminently suited to variable speed . Higher rotational blower speeds produce high volumetric efficiencies, which in turn lower discharge temperatures and power consumption. The Compact Range ensures that all serviceable items are accessed from the front panels of enclosures.
The preliminary intake air filters are combination of cyclone and bag filter and it removes most of the dust from inlet air. Fine filter is a combination of cyclone and 138 ceramic fine filters which removes fine dust very effectively.

Technical Data
Manufacture's type: EB 420 Compact Omega plus 53
Manufactured in year: 2005
Suction capacity with max vacuum:38,0 m3/min
Power demand max: 40,3 kW
Rotor's rotation speed 4120 rpm
Max suction vacuum: 0,53 bar (abs.)
Discharge pressure: 1,0 bar (abs.)
Max pressure increase: 470 mbar
Temperature rise max -t: 82 K
Electric motor: 45 kW û 50 Hz / 400/690V û 83/48 A
Electric motor nominal speed:2965 rpm
Protection class: IP 55
Inverters: Mitsubishi FR-F740-01160-EC
Case ventilation fan: 370 W û 50 Hz / 230 / 400V
Weight blower with the case:1120 kg
Blower case main dimensions:1.8 x 1.7 x 1.8 m (K x L x S)
Noise level: 99 dB (A)
Noise level with the case: 84 dB (A).

We are metals & minerals supply company. Also supply technical products for the industry made from Titanium, Tantalum, Tungsten and alloys and their feeds concentrates.

If you have requirement for
1. Rutile (min 94% TiO2)
2. Ilmenite
3. Scheelite, Wolframite
4. Tantalite
5. Cassiterite

RUTILE is used for :
1. brilliant white pigment in paints, plastics, paper, and foods due to its high opacity and brightness
2. a primary source for producing titanium metal, which is used in aerospace, medical devices, and other high-performance applications
3. in the coating of welding electrodes, providing stability and enhancing the quality of the welds,
4. Due to its high melting point and stability, rutile is used in the manufacture of refractory ceramic

Do not hesitate to contact us.

Mikael Keinonen

R-steel threaded lifting devices including several options as wire loops, wire loops equipped with a pressure plate and full metallic lifting devices, are designed to transport and erect precast units and elements. R-steel lifting devices have been designed and tested according to european quality standards to ensure safe precasting and lifting.

- wire loops are manufactured of high-quality steel wire which are more suitable for on-site high loads such as beams. It can be equipped with a pressure plate for different lifting angles.

- full metallic lifting devices equipped with pressure plate are designed for the lifting of 0 - 90 angles. The free turning swivel can also be used for turning precast elements.

- all threaded lifting devices are easy to install and can be recessed if required, they can be used with all sizes of threaded inner socket anchors.

- inner socket anchors are provided separately from lifting devices and it's highly recommended to use co-ordinated lifting system units for the safety of your precast site. Nailing plates, socket magnets, and plastic caps are also available.

- tailor made solutions are also available.

Totally two identical 145 kW wind turbine units, made in 1988 by Danish A/S Nortank, total operating hours approx 75000. The equipment have been dismatled since 2008 and inspected and serviced for operation condition and they are ready for immediate delivery

We have totally 2 units of uninstalled complete wind turbines manufactured by Danish A/S Nordtank in year 1988, manufactures type NTK 130 with rated power of 2 x 145 kW. The mills are in good operational condition and ready for immediate shipment. The hubs are heat treated MEEHANITE hubs made by company SABROE and are equipped with cast iron construction which allows adjustment for blade pitch angle. The blades are made by Danish company LM- Glasfiber, material is glass fiber reinforced polyester and they have self-supporting structure with bushing roots. The blades have also hydraulically activated tip brakes which automatically rotate the tips to a 90 degree break angle when wind is lost or it can be used for maintenance stoppage. The gear box in made by German Lohman & Stolterfoht and it is two step planetary gear type with high AGMA rating of 302 kW. The break system is 100% fail safe Nortank’s own hydraulically / mechanically activated brakes. Both units have they own Motorola 6809 multi-microprocessor operated control units which are housed in dust proof steel cabinets.

More information on requests, for spam protection please introduce yourself properly.

Main data of one mill:
Manufacture’s type: NTK 130F/LM
Year of manufacture 1988
Total operating hours: approx. 75000
Rated capacity, max: 145 kW
Number of blades: 3 pcs
Rotor diameter: 22 m
Rotor speed: 44.5 rpm
Cut-in wind speed: 4.0 m/sec
Cut-out wind speed: 53 m/sec (120 mph)
Hub height: 26 m
Generator: ASEA 145 kW / 1500 rpm / 50 Hz
Blade type: LM 9.7 m H/H/T diam. 21 m
Gear box type: Lohman & Stolterfort GPC 145
Clutch type: Lohr & Brokamp Universal Joint No 105
Total weight: 15200 kg.

Used computers without hdd p4/p3.
Used laptops mac/p4/p3 without hdd .
Used laser printers.


Products are packed on eur pallets and wrapped with plastic film.

Electric motor scrap

Mix of scrap electric motors from scrap yard owner.
Orders from 1 container to 20 containers per month.
Ex-works = 900 USD / ton (EXW) Finland.
60 km from port of Helsinki (Finland).

This Powerpak 660 horizontal thermoforming machine (form/fill/seal) is manufactured by German Tiromat Krämer+Grebe GmbH & Co in 1998. It is designed for high capacity packing of various products in food and pharmaceutical industry. This unit has been packing bread in to vacuum pack and it is equipped with a three head hot foil printer, 2- gas mixing device for CO2 injection, separate vacuum pump, cross- and longitudinal cutters and water cooled upper cover of the forming unit. Construction material is food quality stainless steel and equipment is controlled with PC-programmable Tiromat Control Unit.

This unit has very little operation hours - estimated total 3000 hours - and therefore it is in excellent condition. Operating and service manuals in English, Finnish and German and machine comes with the CE-certificate.


Machine type:Powerpak 660
Machine number:665/0211
Manufacturing year:1998
Foil type:Flexible
Formatting width:430 mm
Film type used:PS-PE 450/50
Max formatting depth:40 mm
Forming dies:223-3,1
Capacity:10 phases / min
Control unit:Tiromat
Ho foil printer:SC-700 with 3 printing units
Overall length:7.30 meters
Overall width:1.15 meters
Height:1.85 meters
Nominal power need:50 A / 380 V / 50 Hz.

Certificate of quality
Fineness % +-10.0
Initial setting time h:min +-0:45
Final setting time h:min +-10:00
Soundness Mum +-5.0
So3 % +-3.5
Mgo % +-5.0
Loss on ignition % +-5.0
Bending strength mpa +-6.5
Compressive strength mpa +-42.5



1ton/big bag

Common Gypsum Plasterboard
Technical parameters Standards(GB/T9775-1999)

Common Gypsum Plasterboard-specifications
dimension(mm)
depth: 9.5, 12, 15,
width:1200, 1200, 1200,
legnth:3000, 3000, 3000,
weight(kg/m2):7.2,9.0,11.5,
Simple packing specification
No.s: 100,80,60,
area(m2):360,288,216,
weight(ton):2.67,2.69,2.61,
Standard of loading
No.s:76,60,50,
area(m2):273.6,216,180,
weight(ton):2.1,2.1.2.28

Fireproof Plasterboard technical parameters

Standards(GB/T9775-1999)

FireProof Gypsum Plasterboard-specifications
Dimension(mm)
depth: 9.5, 12, 15,
width:1200, 1200, 1200,
legnth:3000, 3000, 3000,
weight(kg/m2):8.2,9.6,12.4,
Simple packing specification
No.s: 100,80,60,
area(m2):360,288,216,
weight(ton):3.04,2.87,2.81,
Standard of loading
No.s:76,60,50,
area(m2):273.6,216,180,
weight(ton):2.39,2.25.2.46

Waterproof Plasterboard technical parameters

Standards (GB/T9775-1999)

Water Proof Gypsum Plasterboard-specifications
Dimension(mm)
depth: 9.5, 12, 15,
width:1200, 1200, 1200,
legnth:3000, 3000, 3000,
weight(kg/m2):8.3,9.7,12.6,
Simple packing specification
No.s: 100,80,60,
area(m2):360,288,216,
weight(ton):3.08,2.90,2.86,
Standard of loading
No.s:76,60,50,
area(m2):273.6,216,180,
weight(ton):2.42,2.27.2.50

GB Standard

U profile horizontal stud
Dimension(mm)
depth: 0.7, 0.7, 0.7,
width:100, 75, 50,
Wingwidth:404040
legnth:3000, 3000, 3000,
Simple packing specification
weight(kg/m):0.9670.8350.698