The line is designed to fill beer in to three different type of 0,33 litre glass bottles, label the bottles neck around and lower body small around and pack the bottles in to 4 x 6 bottle cartoon boxes. This bottling line capacity is 20000 bph. Clean glass bottles were brought on wooden pallets to depalletizer which feed them to the filling lines. Innofill DMG bottle filling machine and Handtmann MMS filtration system are located in a clean air room. KHS lamella conveyor system for bottle transport and cartoon boxes. The equipment were totally delivered by German KHS in year 2003, most of machines manufactured in year 2002. All control units are Siemens Simatic S7 model with remote connection. The line was shut down in year 2008 and it is still installed and in very good operational condition. Main equipment are: - Bottle Depalletizer KHS AL, semiautomatic - Micro Filtration Handtmann MMS 130 - Filling Equipment KHS Innofill DMG (rinsing, filling and capping) - Labelling Machine KHS Innoket 2060 - Cartoon Box Forming Machine KHS Innopak CA-1 - Bottle Packing Robot KHS Innopak SP 1200 - Box Marking System - Case Sealer KHS Innopak CV.
Kisters Wrap Around Packer 310 Kisters fully automated wrap around packer model 310 is a single-lane, high-performance packing robot for producing wrap-around and tray packs from stable individual products. It can handle tins, cans, jars, glass and PET bottles, as well as pre-packed products from the beverage, hygiene and food processing industry with high packaging speeds. It can process flat corrugated cardboard and full carton blanks in different qualities. In each case, the carton is folded tightly around the product groups and subsequently glued with hotmelt and it has a large and easily accessible cardboard blank magazine. Optimum packaging results are achieved in conjunction with the precise cardboard blank guides and the exact folding process. Wrapping robot can handle a wide range of formats. The unit is PLC-controlled and it can be easily adjusted for other packing formats. This machine has been packing beer tins (12/24 x 0.3 liters and 12 / 24 x 0.5 liters) into cartoon wrap-around packs at speed of 60 packs / min. This unit was in full operation till beginning of November 2010 and is now dismantled and stored. Technical Data Manufacturer: Kisters Machinenbau GmbH (Nowadays KHS ) Model: Wrap Around Packer 310 / 100 Year of manufacture: 1994 Serial number: 941782 Capacity: upto 60 cycle / min Electricity: 16 kVA, 400 V / 50 Hz
This laminating tunnel / convection oven is made by Swedish TRIAB / Tri Innovations AB in year 2006. The oven is designed for industrial use and in build up in two separable laminating sections, both equipped with one 40.5 kW hot air sections, one product and one return conveyors and common control unit. All product touching parts are made either of stainless steel (structures and panels) or Teflon made net belts. Convection belt (600 mm wide) is located inside of the oven tunnel and has grid type surface, the return conveyor is installed on the tunnel and it has tight waived Teflon belt. The control cabinet is attached to the equipment structures. The speed of laminating conveyor is adjusted with an inverter driven motor. The speed of return conveyor can be fine tuned via a potentiometer. The equipment is featured with a remote control possibility. This has been operating with hygienic products (material foam / polyurethane film, thickness 5 mm, max. width 450 mm and production speed 6 m/min) and is in excellent operational condition with total 3450 operating hours only and it comes with original operation manual in English language. Technical data: Made by: TRIAD / Air Innovations AB Manufacturing year: 2006 Total operating hours: 3450 Convection capacity: 2 x 40.5 kW Process control PLC: Eurotherm 2216e Hot air circulation volume: 2 x 9000 m3/h Fan electric power: 2 x 2.2 kW Temperature range: 50 – 150 C Total machine length: 10 000 mm Total machine width: 1600 mm Convection belt material: Teflon covered metal net Convection belt length: 9 000 x 600 mm Convection belt speed: 3 – 8 m/s / 0.25 kW, inverted controlled Heated width: 650 mm Inside / free height: 80 mm (from belt to nozzles) Return conveyor: Habasit FAB-8EO WV Return conveyor dimensions: 12000 x 600 mm (Teflon) Return conveyor drive: 0.25 kW, 380 V/50 Hz.
The equipment is designed and manufactured by Gough & Co Ldt, UK in year 1999 / installed in 2000, manufacturer’s type single deck Vibracon GVF4. We have totally 3 identical units which were dismantled in 2007 and all of them are in very good operational condition. These are single deck circular screen design for high velocity scalping, de-watering or single deck separation in chemical and pharmaceutical industry. (These units were screening oversized particles in PVC - granulate factory truck loading station) The perforated screen and all product touching parts are made on stainless steel AISI 304L. Top deck houses the screen and the discharge spout for oversize particle removal is fitted to it. Top deck is supported with mechanical spring and vibration movement is created by two contra rotating vibrating motors on the outside of the unit so there are no internal working parts. Vibration power can be adjusted. Technical data: Type: Vibracon GVF 4 Material: AISI 304L – product touching parts Perforated screen: Mesh size 4 mm Screen diameter: 1100 mm Screen area: 9500 cm2 Vibrators: 2 x 0.52 kW units.
The vacuum evaporator is made by Italian Ecoteck in year 2003 and operation was stopped in early 2009 and it is in very good operational condition. This unit is made for concentrate acidic liquid wastes and therefore all liquid touching parts are made of acid proof steel ( SS 2353) or PVC. The evaporation capacity of the unit is 5000 liters / day. The unit is a complete working unit and it includes evaporator, boiler, heat pump, centrifugal pump, water-air cooler, steam ejector, control unit and all other necessary equipment to complete the unit. Operation principle: Steam rises from the boiler through a drop dispenser to the cooling unit where it condensates. The condensate drops with the gravity down to vacuum system. In-build heat pump heats up the cooling media and simultaneously cools down the condensate. Water – air cooler cools down the extra heat from the process. Necessary vacuum is generated with a centrifugal pump and a steam ejector. Condensate rejection takes place in accordance with prescheduled frequency. Technical data: Manufacturer: ECOTECH Srl Italy / Vilokan Ren Miljöteknik Sweden Type: ECO 5000 VS-HP, R407C Year made: 2003 Evaporation capacity: 5000 liters / 24 hour (pure water) Electricity consump.: about 0,15 kWh / liter pure wateri) Control unit: Siemens Micromaster 420 Compressor: Bitzer Kuhlmachinenbau GmbH, Compressor type: 6G-40,2 Compressor capacity: 126.8 m3/h, 19/28 bar Refrigenerant: R 407 C Main dimensions: 2.8 m x 1.3 m x 2.9 m Weight: 1500 kg.
ating line is delivered by Finnish Elmont Oy and it consist of 59 separate dipping tanks, 6 material handling cranes and related process and automation equipment. We have the dipping tanks and material handling cranes in our store for sale. Dipping tank materials are AISI 316, SS, PP, HST and PP. All tanks are 2200 mm long and 1250 mm height, widths varies from 450 to 1740 mm, volumes from 1213 to 4016 liters. All tanks are in good condition. The cranes are designed for those tanks and we have 6 pcs of them. Cranes have 0.25 kW gear motors and control panels. Structure is made of steel and they are in good condition. If you are looking for such equipment, please contact us and we are pleased to give you more deep information.
Industrial Crane Konecranes CTX 10 t, Dual Bridge with 33.6 m span The crane was manufactured by Konecranes Oyj in 2001 and the operation was stopped in year 2006. The equipment was regularly serviced by the manufacturer and is thus in excellent operating condition. The crane is still installed in its original place and can be tested on any time. The double bridge is welded housing construction equipped with one double speed wire hoists and a motorized rail equipment on both ends. The crane has both the local wire connected control unit as well as the wireless remote controller. On the bridge there is a service platform and the local LV û and control cabinet. All electric motors are dimensioned in accordance with Industrial Heavy Duty ED classification. The equipment includes the crane moving rail which will be sold separately. Technical data: Manufacturer's type:CXTD10t x 33.6m Hol: 6.1m Lifting capacity:10 000 kg Span distance:33.55 m Lifting class:FEM M5 (2m) Bridge structure:Welded case Total weight:Approx 22 000 kg Type of wire hoist:XL 404N40BDA4 Lifting height:6.1 m Lifting speeds:8.0 and 1.3 m / min Wire hoist speeds:32 and 8 m / min Bridge speed:Inverter controlled, max 40 m / min Wire hoist lifting motor:Double power 15 and 2.5 kW (60% ED) Wire hoist moving motors:2 x 0.65 kW (40% ED) Bridge moving motors:2 x 1.8 kW (40% ED) Total power need:19.9 kW / 400 V / 50 Hz Crane moving rail:60 x 40 cm, length 2 x 140 m.
Compressor single stage, standard speed oil-injected rotary screw compressor with manufactured by German company Drucklufttechnik GmbH in year 2002. The complete unit consists of intermediate pressure vessel and Ultratroc - air dryer all delivered same time as the compressor. The unit is controlled by modern DELCOS 3000 control unit. The total unit has 30320 operating hours, the unit has been regularly serviced by a compressor service company and is in good operational condition. The compressor is single-stage, double screw, V-belt driven electric motor drive compressor which has oil cooler and thermostat controlled water - air after cooler on discharge of the pressurized air. The operations were stopped in year 2006 but the compressor and other equipment are still installed and ready for test run. Technical data: Compressor type:CompAir L90 7,5A Capacity:16.1 m3/min, 7.5 bar Comp. electric motor:90 kW - 400/415 V û 50 Hz Air cooler electric motor:3.0 kW - 400/415 V û 50 Hz Compressor weight:2380 kg Compressor dimensions:2.4 x 1.4 x 2.0 m (W x L x H) Air dryer type:Ultratroc SD 1350 û type 422 Air dryer air volume:22.5 m3/min Total power requirement of dryer:2.4 kW DryerÆs refrigerant:Type R134 a û filling 3.5 kg DryerÆs dimensions:1200x900x800 mm, weight 185 kg Int. mediate air pressure vessel:Volume 2 m3, 10 bar, made by Galvanoimis Oy.
This Powerpak 660 horizontal thermoforming machine (form/fill/seal) is manufactured by German Tiromat Krämer+Grebe GmbH & Co in 1998. It is designed for high capacity packing of various products in food and pharmaceutical industry. This unit has been packing bread in to vacuum pack and it is equipped with a three head hot foil printer, 2- gas mixing device for CO2 injection, separate vacuum pump, cross- and longitudinal cutters and water cooled upper cover of the forming unit. Construction material is food quality stainless steel and equipment is controlled with PC-programmable Tiromat Control Unit. This unit has very little operation hours - estimated total 3000 hours - and therefore it is in excellent condition. Operating and service manuals in English, Finnish and German and machine comes with the CE-certificate. Machine type:Powerpak 660 Machine number:665/0211 Manufacturing year:1998 Foil type:Flexible Formatting width:430 mm Film type used:PS-PE 450/50 Max formatting depth:40 mm Forming dies:223-3,1 Capacity:10 phases / min Control unit:Tiromat Ho foil printer:SC-700 with 3 printing units Overall length:7.30 meters Overall width:1.15 meters Height:1.85 meters Nominal power need:50 A / 380 V / 50 Hz.
Drum and Container Filling Line, Semiautomatic YOC 2006 The line is designed for filling both 1000 liter IBC’s and normal 209 liter drums / barrels. It consist of straight chain driven heavy duty roller conveyor which is carrying IBC’s or a standard pallet loaded with four drums / barrels through the filling process and conveying them for further storing. The filling machine is semiautomatic coarse-and-fine filling station; first is programmable volumetric and then fine filling with integrated weighing system. Cap closing / bunging and sealing will be made manually but a machine aided. The station operation is controlled by Siemens S7C programmable logic. The line is manufactured in 2006 by Finnish company “Insinööritoimisto Jyrki Kekälainen” who is specialized supplying automation solutions filling and packing applications. Operation description: The operator lifts the empty containers on the conveyor (open the cap of container), the container will move into filling machine and it will be filled automatically with 2 "and 1 / 2" valves, coarse-and fine-filling. After filling the container will move out of the machine and the operator will fix the label and close the cap. After the filling station there is ~16 m long puffer conveyor for the filled IBC`s, where a fork lift will pick up the IBC`s In drum filling the operator lifts the empty drums on pallet (open the caps). Then he lifts the pallet on the conveyor. In the machine there is an extra filling lence for the drums. The drums are filled on the weighing system of the machine which is controlling the filling of each barrel. After the drum is filled the operator move the lence into second drum and machine start to fill it. After all drums are filled the pallet will move out of machine and the operator will close the caps and fix the seals and labels. Technical data: Manufactured in: 2006 Suitable for: Standard IBC and Drums Max filling weigh: 1500 kg Filling accuracy: 0.5 kg Filling capacity: 7 IBC/hour or 35 Drums (209 liters) / hour Roller conveyor type: Chain Driven, Galvanized Roller conveyor length: Approx 16 meters Roll diameter: 80 mm.
GEA Varitherm VT-20 Plate Heat exchanger is made of several Varitherm-design stainless steel plates which are combined to form one effective heat transfer unit. Within each plate package the heat exchanger plates support each other at the metal-on-metal profile cross points, which ensure the stable behavior of the plate gap. The plate gasket has so called glue less sealing system. VT-20 is specially designed for cooling and heating of fluids with particle content up to a particle size of 2 mm as well as condensation of vapors, gas cooling and gas dehumidifying. This unit is in good operational condition. Manufacturer: GEA Ecoflex GmbH Type: VT 20 BC-12 Serial no: 170/12982 Year of manufacture: 2000 Frame material: Stainless Steel AISI 4571 Plate material: Stainless Steel Max. operating pressure: 16 Bars Max. operating temp. 100 C Max flow volume: 90 m3/h Width: 337 mm Length: 999 mm. Manufacturer: GEA Ecoflex GmbH Type: VT 20 BC-12 Serial no: 170/12982 Year of manufacture: 2000 Frame material: Stainless Steel AISI 4571 Plate material: Stainless Steel Max. operating pressure: 16 Bars Max. operating temp. 100 C Max flow volume: 90 m3/h Width (plates) 337 mm Length (plates): 1370 mm.
Double floor tool storage made of removable metal structure. Walls on 3 sides of the storage, one side is main building wall. Includes two lockable separate storage rooms and selves. Free height in lower level is 2.7 meters. Material is steel and aluminum. Will be sold as is where is bases.
Plasmatreat FG1002 pre-treatment and cleaning unit This flat surface pre-treatment and cleaning unit with open air / atmospheric-pressure plasma technology was originally made by Plasmatreat company in 2004, manufacturer's model FG1002 with Siemens PLC control system and then in year 2008 it was refurbished with new plasma nozzle directing robot and an aluminium profile structured operation table. The unit has two plasma nozzles and it has been used on occasionally and is in excellent condition. The equipment has CE marking and proper documentation, including wirering diagrams This machine is designed to pre-treat and clean any metal, aluminum, plastics (such as PP and EPDM) or glass surface free from grease, dust and other unwanted materials and to pre-treat material surface for ensuring the adhesion of surface coating to these materials. Plasmatreat process also allows to use environmentally friendly water-based painting for coating and due to the fact that cleaning with plasma is a dry process immediate further processing of the materials is possible. For more information, please visit manufacturer's web page www.plasmatreat.de Technical information: Manufacturer:Plasmatreat Company Model:Plasmatreat Openair® FG 1002 Serial number:695 Year of manufacturing:2004 / 2008 Operation table size:1600 x 3000 mm Electricity connection:3~/ 400V / 32 A Condition:Used, excellent.
Workwear, T shirts, fabrics, and southeast asian rice.Clearing agent, transportation and shipping
White talc powder 400 mesh.
Waste paper.
Plastic scrap.
D6 Virgin Oil and JP A1-JP54.
Hardwood pulp and softwood pulp.
Crude oil.Agent
