FEATURES 3s statistical interval, continuously record 168h Support multi-brand current transformer Up to 32G data storage space Record up to 461 power energy parameters simultaneously Up to 10000 screenshots saved Support periodic recording function Up to 3.9M/s USB high-speed transfer Recording wave FUNCTIONS Energy loss calculator: classic active and reactive power measurements, unbalance and harmonic power, are quantified to pinpoint true system energy losses in dollars (other local currencies available). Power inverter efficiency: simultaneously measure AC output power for power electronics systems. Power wave data capture: GF438II analyzers capture fast RMS data, show half-cycle and waveforms to characterize electrical system dynamics (generator start-ups, UPS switching etc.). Waveform capture: GF438II capture 50/60 cycles (50/60Hz) of each event that is detected in all modes, without set-up Automatic transient GF438II analyzers capture 200 kHz waveform data on all phases simultaneously up to 1000V. Fully class-A compliant: GF438II analyzers conduct tests according to the stringent international IEC 61000-4-30 class-A standard. Mains signaling: GF438II analyzer measure interference from ripple control signals at specific frequencies. Troubleshoot: analyze the trends using the cursors and zoom tools. Highest safety rating in the industry: 600 V CAT IV/1000 V CAT III rated for use at the service entrance. Measure all three phases and neutral: with included four flexible current probes with enhanced thin flex designed to fit into the tightest places. Automatic trending: every measurement is always automatically recorded, without any set-up. System-monitor: ten power quality parameters on one screen according to EN50160 power quality standard Logger function: configure for any test condition with memory for up to 600 parameters at user defined intervals. View graphs and generate reports: with included analysis software. Battery life: up to 5 hours operating time per charge on Li-ion battery pack.
FEATURES Measure phase angle between two voltages, between two current or between voltage and current Measure alternating voltage (U), alternating current (I), frequency (F), active power (P), reactive power (Q), power factor (PF) and so on. Current signal is obtained by the clamp current transformer on line directly Discern inductive circuit and capacitive circuit; Directly read differential protection phase among every unit of CT Can check connection of transformer Measure two way voltage phase sequence Can check whether the meter connection is right or not Can evaluate the running speed of electric kWh meter High resolution of current, so can be used as a leakage current meter
GF211 double clamp phase volt-ampere meter is a multi-functional portable instrument. It can measure not only alternating voltage, but also alternating current. Its important function is to measure phase angle between two voltages, between two current or between voltage and current. The current signal is obtained by the clamp current transformer without cutting off current wire. It can discern inductive circuit and capacitive circuit; can directly read differential protection phase among every unit of CT; can check connection of transformer; measure three way voltage phase sequence; can check whether the meter connection is right or not; can evaluate the running speed of electric kWh meter. It has high resolution of current, so can be used as a leakage current meter. It is an ideal choice for electric power bureau, factories, mine, petroleum -chemistry enterprises, metallurgy factories and so on.
Electrical parameters Power voltage AC220V±10% or AC110V±10%, 50/60Hz±10% Time measurement 0.1ms-999999.999s AC current output Phase current output (effective value) 3 x 0-30A Maximum power output 260VA/phase Maximum parallel current output (effective value) 0-90A Long-term allowable working value of phase current (effective value) >10A Allowable working time of maximum current >11s Accuracy class
PARAMETERS Electrical parameters Power voltage AC220V±10% or AC110V±10%, 50/60Hz±10% Time measurement 0.1ms-999999.999s AC current output Phase current output (effective value) 3 x 0-30A Maximum power output 260VA/phase Maximum parallel current output (effective value) 0-90A Long-term allowable working value of phase current (effective value) >10A Allowable working time of maximum current >11s Accuracy class
Shandongsenyuan new energy technology co., LTD., SYNE founded in 1998, is a leading manufacturer of power generation solutions in China. We specialize in the design, sale, installation, maintenance and service of gas power stations produced by natural gas, methane, diesel, biomass gas, petroleum associated gas, coal gas, landfill and sewage treatment. And provide project consultation, system design, technical support and other services; www.sy-ne.com Our products: Farm power generation, diesel power generation, natural gas power generation, heavy oil power generation, garbage power generation garbage power generation project design, the contractor and operation; 100Kw - 3000Kw generator set, etc.
Shandongsenyuan new energy technology co., LTD., SYNE founded in 1998, is a leading manufacturer of power generation solutions in China. We specialize in the design, sale, installation, maintenance and service of gas power stations produced by natural gas, methane, diesel, biomass gas, petroleum associated gas, coal gas, landfill and sewage treatment. And provide project consultation, system design, technical support and other services; www.sy-ne.com Our products: Farm power generation, diesel power generation, natural gas power generation, heavy oil power generation, garbage power generation garbage power generation project design, the contractor and operation; 100Kw - 3000Kw generator set, etc.
ï¼?SYNEï¼?ï¼?Shandongsenyuan new energy technology co., LTD., founded in 1998, is a leading manufacturer of power generation solutions in China. We specialize in the design, sale, installation, maintenance and service of gas power stations produced by natural gas, methane, diesel, biomass gas, petroleum associated gas, coal gas, landfill and sewage treatment. And provide project consultation, system design, technical support and other services; Our products: Farm power generation, diesel power generation, natural gas power generation, heavy oil power generation, garbage power generation garbage power generation project design, the contractor and operation; 100Kw - 3000Kw generator set, etc.
50w constant voltage led transformer
Generator capacitors Details Our company specializes in export run capacitor Basic Information: product: Generator capacitors Design Style: High Cylindrical Inner Core: one core Core material: Aluminum foil Capacitor connection type: two cables (Double lead), Sealing material: PO oil Outer.
Power of Lamp 4*1000W Generator Power 6KW Elevation Height 700CM By Hand-operated Working Time 42-45H Anti-wind Capacity less than 6-G Frequency 60HZ Engine Brand KIPOR Power Rating 6KVA Luminous Flux 440000LM Insulation Grade H Generator Brand SENCI Model Number FHZM-T Model Number FHZM-T SHIPPING SIZE 408*160*175CM -
Introduction DCEM are special design for DC circuit metering, muti-channels signal design can much reduced the hardware cost of project. One meter provide different four channel amp reading and energy consumption value record. Same 35mm din rail mounting shell can work with Blue Jay MCM series meter for combine energy metering project in AC & DC circuit. Optional analog, digital, relay and alarm output is available via field-swappable plug-in communications modules. Also provide on-board RS485 serial communication port (MODBUS RTU) to send data to the external systems. Main features DC power / energy sub-meter provides Voltage, Current, Power and Energy measurements Monitor and control power switches Bi-directional for renewable systems (NET metering) Interfaces with shunt or external Hall Effect current sensors Up to 1000Vdc Voltage input Up to 4 channels energy metering Record last 30days energy data for all channels RS-485 connectivity - Modbus RTU Optional alarming and analog output Optional 4 channels digital inputs / 2 channels digital outputs
Introduction Low cost solution for power line parameter monitor, standard with LED display, visual display of the most commonly used data Using electrical parameters means using several analog or digital single-function products such as ammeters, voltmeters or watt meters. 0.5class high-precision performance, can instead of your old analog indicator or digital single-function products such as ammeters, voltmeters or watt meters etc. Main features Class 0.5 power and energy Current measuring .../5 or .../1 A Optional RS-232 Modbus/RTU Communications Backlit red LED display Optional mini type installation dimension (72X72mm) ITF Technology: galvanic insulation protection inputs outputs Universal series power supply (85-265VAC/DC)
Introduction Advance power meter, provide RS-485 communication port, easy for user connect to PLC and build SCADA system. Higher measurement accuracy(0.2) and system stability, it is cost effective ideal for OEMs and panel builders solution. (Option LED display screen) Main features Class 0.5 power and energy Current measuring .../5 or .../1 A Backlit LCD display Expandable input / output modules (up to 3 modules) With RS-485 Modbus/RTU Communications With 2 channel Pulse Output (PO) for active energy &reactive energy counting Optional 1 channel Analog Output (AO) ITF Technology: galvanic insulation protection inputs outputs Universal series power supply (85- 265VAC/DC)
Introduction Three phase electrical network power quality detection device, provide energy consumption and generate; THD (Total Harmonic Distortion); Harmonic individual data reading. Build-in 4 tariffs energy logger function, with onboard memory can record last three month energy data, free to set max 12 segment record period, can be use as a commercial billing unit. Main features Class 0.5S power and energy Current measuring .../5 or .../1 A Backlit LCD display Expandable input / output modules (up to 3 modules) With RS-485 Modbus/RTU Communications With 2 channel Pulse Output (PO) for active energy &reactive energy counting Optional 1 channel Analog Output (AO) Optional 4 channel Digital Input (DI) and 2 channel Digital Output (DO) Record and read multi- tariffs ratio, Up to 3 months ITF Technology: galvanic insulation protection inputs outputs Universal series power supply (85- 265VAC/DC)
Introduction New 194J series Smart Power Manager is the more powerful meter than 194Y series power analyzer. With higher precision and more measurement parameters. This meter is the latest series meter developed in 2015 by Blue Jay tech. It is the ideal choice for monitoring and controlling of power distribution systems. Main features Class 0.2 power and energy Current measuring .../5 or .../1 A Backlit LCD display Expandable input / output modules (up to 3 modules) With RS-485 Modbus/RTU Communications Measured varies of power parameter. (Max demand/ unbanlance/crest factor/K factor...) Optional 2 channel Digital Input (DI) and 3 channel Digital Output (DO) Record and read multi- tariffs ratio, Up to 3 months Provide max 50 lists SOE record function ITF Technology: galvanic insulation protection inputs outputs Universal series power supply (85-265VAC/DC)
Introduction High-end multifunction power analyzer manufactured by Blue Jay Technology. Higher measurement accuracy, and powerful functions. With its four direct access keys and TFT displays, friendly full text interface helps user operate device more easy. Max 52th harmonic individual monitor, let user clear grasp of the present electrical grid quality. Main features Class 0.2 power and energy Current measuring .../5 or .../1 A Clear and large matrix LCD screen Expandable input / output modules (up to 3 modules) With 2 channel Pulse Output (PO) for active energy &reactive energy counting With RS-485 Modbus/RTU Communications Optional 1 channel Analog Output (AO) Optional 4 channel Digital Input (DI) and 2 channel Digital Output (DO) Record and read multi- tariffs ratio, Up to 3 months Electrical parameter MD record ITF Technology: galvanic insulation protection inputs outputs Universal series power supply (85-265VAC/DC)
Introduction The MCM1000 Series provides a compact and robust metering solution, enable reliable monitoring of building electrical loads with a low installation cost-per-point by combining sub-metering. The unit performs real-time metering, measures energy consumption, multi tariff time-of-use (TOU) and monitors power quality for max 18 channel circuits for single phase or 6 channel for three phase circuits. Advanced communications options including Modbus via RS485, I/O communications provide for extensive reliable data exchange. Multiple units can be connected together to meter unlimited number of circuits. The versatility of MCM1000 meters are ideal for multi-tenant or departmental metering applications within office towers, condominiums, apartment buildings, shopping centers and other multi-user environments. Main features Class 0.5 basic parameter and class 1 for active energy 6 channels three phase or 18 channel single phase metering Current measuring .../5 or .../1 A (optional 333mV) Standard 35mm - 8 module DIN rail mounting Provide RS-485 MODBUS-RTU Communications Optional 6DI / 2DO for signal detect and remote control Optional external connection LCD screen, 96*96mm panel mount Optional TOU record for each monitor channel Accept customization design
Introduction The MCM400 main for Non - industrial users sub-metering, use ../100mA or 0.333mV CT, split core design easy for install, Din-rail mounting for every style of electrical panel in build. The unit performs real-time metering, measures energy consumption, multi-tariff time-of-use (TOU) and monitors power quality max 4 channels circuit for three phase circuits, with LCD screen and keypad for easy for configuration. RS485 port can send out collected value to remote host. Enable reliable monitoring of building electrical loads with a low installation cost-per-point by combining sub-metering. It is ideal for multi-tenant or departmental metering applications within office towers, condominiums, apartment buildings, shopping centers and other multi-user environments. Main features Class 0.5 basic parameter and class 1 for active energy 4 channels three phase metering Current measuring .../5 or .../1 A (optional 333mV) Standard 35mm - 4 module DIN rail mounting Provide RS-485 MODBUS-RTU Communications Build in LCD screen, keypad for configuration Optional TOU record for each monitor channel Accept customization design
