Acidity testing kit, field testing kit, transformer oil.
Spectrometer, optical power meter.
Water temperature gauge, electrical temperature gauge, oil pressure gauge, air pressure gauge, engine pressure gauge, transmission pressure gauge, R.P.M. (round per minute), hours meter, speedometer, fuel meter, volt meter, ammeter, hourmeter digital.
Level gauge, transmitter, flow meter.
Sawn timber, cca treated timber and poles, electric meters.
Instruments, meters, chemical reagents and consumptive materials.
Fiber optic, fusion splicer, fiber cleaver, media converter, video converter, OTDR, power meter, laser source, red source, polishing machine, optical equipment, fiber instrument, fiber cable.
PCB relay, auto relay, solid state relay, power relay, timer relay, contactor, voltage regulator, KWH meter.
Power meter, multifunction power meter, energy meter, power quality analyzer, wireless temperature and humidity measurement system.
Digital multimeters, digital clamp meters, laser distance meters, ir thermometer.
Application: HV test shielding room (faraday cage) are Widely used in power cable, transformer, transformer switch, transformer substation and other High voltage levels of partial discharge test or impulse test. For HV testing shielding room, as a HV test place, it should has good electromagnetic shielding condition. And its electromagnetic compatibility always is of great importance. Firstly, it should restrict electromagnetic wave into inside shielding room caused by discharge when making HV test to weakening interfere to outside, especially on electronic and communication system. Secondly, it should prevent outer electromagnetic wave intruding into shielding room to cause measurement error of partial discharge and wireless. Thirdly, it should reduces open circuit voltage and closed current to restrain common-mode interference so that to avoid equipment damage and to improve accuracy of impulse measurement. For GIS HV test shielding room, design area is 500 m2ï¼?Length 25mã??Width 20m). From provided information , we find that steel structure have been completed already with one set of 20T crane indoor, crane supporting corbel also completed, the height is 17.9m from ground to upper part of corbel. Main door height 13m,width 10m, locates at downward of the west side, the door open direction towards to north . According to ILJIN drawing, three side of structure column has already, but western structure column still missing yet. however, as the main door will be located in this side, the western side also should have steel structure , and this structure position still should be unified considered with main door installation. We will be able to submit suggested design diagram with position & size of this structure column for reference. in order to save construction cost, the construction engineering will be carried out by ILJIN team.
Scratch Grinding Tester Automobile line inspection equipment Wire and Cable Detection Equipment It is applicable for assessing the scratch-resistant performance of automobile wire insulation with external forces in line with the requirements of GB/T12528-2008. Main parameters: 1. The scratch grinding device exercises in two directions along wire axes with a stroke above 10mm 2. Exercise frequency: 50~60 cycles/min 3. Minimum distance between test points and test point and test sample end: >10mm; rotation angle of test sample: 90° 4. Length of test sample: Test sample which is about 750mm is firmly fixed to a steel anvil 5. Weight: 400, 700, 1000g (weights applied to scratching needle) 6. Function: The device will stop when the scratching needle grinds through insulation and comes into contact with conductor
Resistance Test Instrument Supplier ZY9733 and ZY9734 digital desk type low current resistance measuring meters are suitable for units concerned to measure the DC resistance of various components and parts with certain limitations on current, such as platinum resistor, coppery thermal resistor, PTC ceramics, thermistor and various wire rods, etc. 1. Key features 1.1 It adopts a large green LED to display measured value, which is striking and clear. It also adopts the four-terminal resistance measurement method to eliminate the impact of conductor resistance, and the measurement accuracy is high. 1.2 There are a variety of specifications, and each specification has four scales to meet the measurement requirements of different users. 1.3 The test current is lower than similar equipment, which effectively prevents the impact of components and parts on resistance. 1.4 ZY9734 type has a RS-232 serial data output interface to facilitate the connection to computer. 1.5 It adopts a novel plastic shell and can changes the inclined angle between the device and table by adjusting the handle position, so as to determine the suitable panel observation angle. It has a well-designed appearance and is easy to use. 2. Main technical indicators Temperature: Reference conditions: 20±5; nominal condition: 5~35 Relative humidity: Reference conditions: 40~60%; nominal condition: 25%~75% Power source: AC 220V±10%, 50Hz, power consumption: About 5VA.
Sawdust Moisture Meter MS-W Sawdust moisture meter with seperate probe MS-W used for measuring moisture content of wood materials(such as sawdust,paillasse,bamboo powder and wood chips).It applicable of paper making , flakeboard , furniture and mechanism of charcoal industry. Features: * It is portable, compact, easy to use and the moisture measurement readings are instant. * Digital display with back light gives exact and clearly reading although you stay at the somber conditions. * The moisture meter operation has automatic temperature compensation. * Data hold function. * Low battery alert. Specifications: Digits LCD with backlight Measuring range :0-84% Operating conditions: Temperature:0-60 Humidity:
JH Digital Tension Meters Large, easy to read backlit, graphic display with adjustable backlighting and contrast. Display shows tension, name of calibration selected, running line minimum and maximum tension values, and battery charge level. Indicate length of material in feet or meters.
JH Digital Tension Meters Large, easy to read backlit, graphic display with adjustable backlighting and contrast. Display shows tension, name of calibration selected, running line minimum and maximum tension values, and battery charge level. Indicate length of material in feet or meters.
JH Digital Tension Meters Large, easy to read backlit, graphic display with adjustable backlighting and contrast. Display shows tension, name of calibration selected, running line minimum and maximum tension values, and battery charge level. Indicate length of material in feet or meters.
JH Digital Tension Meters Large, easy to read backlit, graphic display with adjustable backlighting and contrast. Display shows tension, name of calibration selected, running line minimum and maximum tension values, and battery charge level. Indicate length of material in feet or meters. Packaing:59*78*183mm
SCR Voltage Regulator
•Large and easy-to-read LCD •Data Hold Function •Waterproof and designed to float •Automatic Temperature Compensation •Replaceable probe
