Description The Trusted TMR 24 / 48V dc Digital Output module interfaces to 40 field devices. Triplicated diagnostic tests are performed throughout the module including measurements for current, and voltage on each portion of the voted output channel. Tests are also performed for stuck on and stuck off failures. Fault tolerance is achieved through a Triple Modular Redundant (TMR) architecture within the module for each of the 40 output channels. Automatic line-monitoring of the field device is provided. This feature enables the module to detect both open and short circuit failures in field wiring and load devices. The module provides on-board Sequence of Events (SOE) reporting with a resolution of 1ms. An output change of state triggers an SOE entry. Output states are automatically determined by voltage and current measurements on board the module. Features 40 Triple Modular Redundant (TMR) output channels per module. Comprehensive, automatic diagnostics and self-test. Automatic line monitoring per channel to detect open circuit and short circuit field wiring and load faults. 2500V dc optical isolation barrier. Automatic over-current protection (per channel), no fuses required. On-board Sequence of Events (SOE) reporting with 1ms resolution. Module can be hot-replaced on-line using dedicated Companion (adjacent) Slot or SmartSlot (one spare slot for many modules) configurations. Front panel output status LEDs for each channel indicate output status and field wiring faults. Front panel module status LEDs indicate module health and operational mode (Active, Standby, Educated) TUV Certified IEC 61508 SIL 3 Outputs are powered in isolated groups of eight. Each power group can be of a different voltage
Description The Trusted TMR analogue input module interfaces to 40 single-ended field input devices. A wide input range and programmable thresholds allow the module to be used in most voltage or current configurations. Comprehensive diagnostic tests are performed on each input channel, including tests for out of range values and stuck at failures. Fault tolerance is achieved through Triple Modular Redundancy (TMR) within the same module for each of the 40 input channels. The module can apply a digital filter to each input channel. Individual channels can be configured for high noise immunity (50Hz or 60Hz rejection), low noise immunity (fast response) or pass-through operation (no filtering). Each input channel has four configurable state thresholds, which may be assigned to SOE reporting. A change of state triggers an SOE entry. The on-board sequence of events (SOE) reporting has a resolution of 1ms. Each triplicated section of the module, referred to as a slice, conditions and measures each channel independently. Each slice is optically isolated up to 2500V dc. Each slice sends its data to a safety layer hardware voter that presents the information from all three slices to the Trusted TMR processor. When a fault is detected on a slice of the module, the Trusted TMR processor will flag the error, indicating the need to replace the module. The Trusted TMR processor will continue to use the information provided by the remaining two slices until a replacement module is available. Replacement modules can be located in a standby slot next to the module or in a designated SmartSlot with a temporary connection to the same Trusted termination assembly. Modules may be placed in any I/O module slot in a Trusted processor chassis or expander chassis. Once the I/O module configuration is set, mechanical keying is available on all I/O modules to prevent inserting a module into an incorrect slot. Configuration of the module is carried out using the Trusted Toolset running on an engineering workstation. Once configured and loaded into the Trusted controller, replacement modules are online educated by the TMR processor. Features 40 TMR input channels per module. Comprehensive diagnostics and self-test. 2500V dc optically isolation. Digital signal filtering on a per channel basis. Four user configurable thresholds per channel. On-board 1ms resolution sequence of events reporting. Hot replaceable. Front panel status LEDs for each channel. Module fault and status indicators. IEC 61508, SIL 3 safety applications.
Description The Trusted 40 Channel Analogue Input FTA T8830 is designed to act as the main interface between a field device generating an analogue signal and the Trusted TMR Analogue Input Module T8431. Features 40 input channels per FTA. Industry standard field device connections (2-wire). Standard DIN rail compatibility. Simple installation and connection. 24V dc operation. SmartSlot connection for one to many hot replacement of input modules. Fused field power supply per channel. On-board LED indication field power supply integrity.
General Information Product ID: 3BSE051306R1 Medium Description: AI835A Analog input Module, 8 channels, thermocouple/mV Technical Information: Supersedes 3BSE008520R1/3BSE008520Z1/ 3BSE051306Z1 Product Type: I/O Module Country of Origin: Estonia Customs Tariff Number: 85389091 Length: 150 mm Height: 150 mm Width: 75 mm Weight: 0.2 kg
General Information Product ID: 3BSE028925R1 Medium Description: AI843 Analog Input Module, 8 channels, Redundant or Single, thermocouple /mV Product Type: I/O Module Country of Origin: Estonia Customs Tariff Number: 85389091 Length: 102 mm Height: 119 mm Width: 45 mm Weight: 0.25 kg
General Information Product ID: 3BSE052605R1 Medium Description: AO815 Analog Output Module, 8 channels with HART Product Type: I/O Module Country of Origin: India Customs Tariff Number: 85389091 Length: 102 mm Height: 119 mm Width: 45 mm Weight: 0.3 kg
16 Channels Isolated Digital Output * 16-ch. Isolated Single-Ended output * Open drain Output (P-MOSFET) * Max. Output load current 3A/per channel * Programmable Host Watchdog Timer For Host Failure Protection. * Support MODBUS RTU And ASCII Format Protocol
8 Isolated differential digital input * Support 8 isolated differential digital input * Input channel support max. 50Hz counter * Programable Host Watchdog Timer For Host Failure Protection. * Support MODBUS And ASCII Format Protocol
16 Non-Isolated digital input channels * Support 16 non-isolated digital input channels * Input channel support max. 50Hz counter * Programable Host Watchdog Timer For Host Failure Protection. * Support MODBUS And ASCII Format Protocol.
8 Isolated digital input and 8 Isolated digital output * Support 8 Isolated digital output * 650mA current Sink per DO channel * Support 8 isolated digital input channels * Input channel support max. 50Hz counter * Programmable Host Watchdog Timer For Host Failure Protection. * Support MODBUS RTU And ASCII Format
8-ch ISO DI and 3-ch AC-SSR Output with LED display * Support 8 isolated digital input channels * Input channel support max. 50Hz counter * Support 3 relay output channels (Form A) * Programmable Host Watchdog Timer For Host Failure Protection. * Support MODBUS And ASCII Format Protocol
5-ch ISO DI and 5-ch relay Output with LED display * Support 5 isolated digital input channels * Input channel support max. 50Hz counter * Support 5 Relay output channels (Form A) * Programmable Host Watchdog Timer For Host Failure Protection. * Support MODBUS And ASCII Format Protocol
EDAM-9051 12 DI, 2 DO and 2 Counter channels Digital I/O Module * Support Modbus/TCP,TCP/IP,UDP,ICMP,ARP * Ethernet 10/100 Based-T Communication * Support 2 Isolated digital output channels (NPN). * Provide Pulsed/delay Output Mode * Support 12 Isolated digital Input Channels * 2 counter (4.5 KHz) input channels * Support Dry Contact Inputs * Fully Photo-Isolation 3750Vrms * Status LED indicatorr
EDAM-9063A 7-channel Digital Input and 3 RELAY Output module * Support Modbus/TCP,TCP/IP,UDP,ICMP,ARP * Ethernet 10/100 Based-T Communication * Support 3 relay output channels (Form A) * Provide Pulsed/delay Output Mode * Support 7 Isolated digital Input Channels * Provide Counter/ Frequency Inputs Mode * Support Dry/ Wet Contact Inputs * Fully Photo-Isolation 3750Vrms * Status LED indicator
8 Isolated Digital output and 4 Isolated digital input * Support 8 Isolated digital output channels * Open Collector Output (NPN) * Support 4 isolated digital input channels * Input channel support max. 50Hz counter * Programmable Host Watchdog Timer For Host Failure Protection. * Support MODBUS RTU And ASCII Format
8-ch ISO DI and 3-ch DC-SSR Output with LED display * Support 8 isolated digital input channels * Input channel support max. 50Hz counter * Support 3 DC-SSR output channels * Programmable Host Watchdog Timer For Host Failure Protection. * Support MODBUS And ASCII Format Protocol
5-ch ISO DI and 5-ch AC-SSR Output with LED display * Support 4 isolated digital input channels * Input channel support max. 50Hz counter * Support 5 AC-SSR output channels * Programmable Host Watchdog Timer For Host Failure Protection. * Support MODBUS And ASCII Format Protocol
EDAM-8067AD 8 channels Isolated Relay Output (5A/250Vac, 5A/30Vdc) * 8-Channels relay Output * Normal Open Relay Output(Form A) * Relay contact rating 5A/250Vac, 5A/30Vdc. * Programmable Host Watchdog Timer For Host Failure Protection. * Support MODBUS RTU And ASCII Format
EDAM-9052AB Ethernet 8-DI ISO (Dry/Wet contact) and ISO 8-DO module * Support Modbus/TCP,TCP/IP,UDP,ICMP,ARP * Ethernet 10/100 Based-T Communication * Support 8 isolated digital output with Open Drain. * Provide 3A/per output channel. * Provide Pulsed/delay Output Mode * Support 8 Isolated digital Input Channels * Provide Counter/ Frequency Inputs Mode * Support Dry/ Wet Contact Inputs * Fully Photo-Isolation 3750Vrms
16-CH Input module W/LED * Support 16 isolated Input channels. * Input channel support max. 50Hz counter * Programmable Host Watchdog Timer for Host Failure Protection. * Support Modbus and ASCII Format Protocol.
