DeRun Energy Co could provide Drilling Waste Management System such as solid control equipments of shale shaker, shaker vibrators, shaker screens, decanter centrifuge, sand pump, centrifugal pump, vertical cutting dryer, mud cleaner, vacuum degasser, screw pump, mud agitator, screw conveyor, etc
1. ADVANTAGES OF DOWNHOLE MOTOR Increased rate of penetration. Better hole deviation control. Reduction in drill string failure rate. Reduction in wear and tear of the swivel, Kelly, and rotary drives. Reduction in fuel cost, since compared to rotary drilling, less energy is required to power a downhole motor. 2. CONSTITUTION Downhole motors differ in size and performance characteristics, but they share the same basic components as follows (Fig.1) : Crossover Sub Safety Catch Sub Power Section Coupling Assembly Bearing Assembly
The sucker rod, an essential part in the rod production system, is used to connect the pumping unit on the ground and the oil well pump down in the well.Products comply with Specifications of Sucker Rods (API Spec 11B) and other related standards, and have acquired the authorization to use Official API Monogram.The company produces K, C, D or HL sucker rods with various specifications complying APIâ??s requirements. Technical Performance & Characteristics 1,Advanced online fault detection, hardening, continuous overall tempering and ball blast techniques are incorporated so that mechanical strength and overall performance are enhanced. 2,Threads are processed on special numeral control lathes avoiding any rotation of the rod and then subject to roll forming so as to ensure high precision, reliable performance and extended service life.
Casing is used for fastening oil and gas well wall or borehole,with bigger diameter than tubing ,including surface casing,technical casings and oil layer casing . Usage: Petroleum Casting Tube, Oil Pipe, Steel tubing, Casing, Drill pipe Standard: ISO, API 5CT, API 5D, API 5L provide: size:4-1/2 5 5-1/2 6-5/8 7 7-5/8 8-5/8 9-5/8 10-3/4 11-3/4 13-3/4 13- 3/8 16 18-5/8 20 OD:114.3-508.0mm weight :9.5-133.0b/ft Thickness :5.21-16.13mm Type of end :J55/K55 M65 L80/C95 N80 C90/T95 P110 Q125
1.Description: The mechanical-hydraulic drilling jar is a jarring and stuck releasing tool. It integrates the up jar and down jar and can release the stuck accident occurring during drilling operation. The drilling jar is an ideal tool for directional well and deep well drilling. Operating principle 1.Operating principle of up jar Lifting drilling tool, slip assembly which bear the acting of dish reed elastic force and slip locking force compels latch mechanism of slip clasp slip mandrel. While slip mandrel up run with mandrel to overcome slip locking force and damping action between hydraulic valve assembly and spindle extension, jar Make drill stem accumulate energy, delay time. When mandrel up run to the state of release constraint, elastic potential energy accumulated in drill stem will convert to upward kinetic energy, generate up jar. If need sequence up jar, you need fed off drilling tool till relock latch mechanism, reduplication above process, Generate sequence up jar. 2.Operating principle of down jar The loosen load of down jar lock can be transfer as per in demand .There are a certain ratio between up locking force and down locking force , and the ratio is adjustable. If down jar, fed off drilling tool until pressure reach to down locking force, jar should generate down jar force. If need to repeat jar, lifting drilling tool to anew securing position repeat above process.
1.Description: The mechanical-hydraulic drilling jar is a jarring and stuck releasing tool. It integrates the up jar and down jar and can release the stuck accident occurring during drilling operation. The drilling jar is an ideal tool for directional well and deep well drilling. Operating principle 1.Operating principle of up jar Lifting drilling tool, slip assembly which bear the acting of dish reed elastic force and slip locking force compels latch mechanism of slip clasp slip mandrel. While slip mandrel up run with mandrel to overcome slip locking force and damping action between hydraulic valve assembly and spindle extension, jar Make drill stem accumulate energy, delay time. When mandrel up run to the state of release constraint, elastic potential energy accumulated in drill stem will convert to upward kinetic energy, generate up jar. If need sequence up jar, you need fed off drilling tool till relock latch mechanism, reduplication above process, Generate sequence up jar. 2.Operating principle of down jar The loosen load of down jar lock can be transfer as per in demand .There are a certain ratio between up locking force and down locking force , and the ratio is adjustable. If down jar, fed off drilling tool until pressure reach to down locking force, jar should generate down jar force. If need to repeat jar, lifting drilling tool to anew securing position repeat above process. Main feature: Drilling jar with national oilwell varco Hydromechanical drilling jar halliborton Operating manual double acting drilling jar Used in geothermal drilling and wells
1.Description: The mechanical-hydraulic drilling jar is a jarring and stuck releasing tool. It integrates the up jar and down jar and can release the stuck accident occurring during drilling operation. The drilling jar is an ideal tool for directional well and deep well drilling. Operating principle 1.Operating principle of up jar Lifting drilling tool, slip assembly which bear the acting of dish reed elastic force and slip locking force compels latch mechanism of slip clasp slip mandrel. While slip mandrel up run with mandrel to overcome slip locking force and damping action between hydraulic valve assembly and spindle extension, jar Make drill stem accumulate energy, delay time. When mandrel up run to the state of release constraint, elastic potential energy accumulated in drill stem will convert to upward kinetic energy, generate up jar. If need sequence up jar, you need fed off drilling tool till relock latch mechanism, reduplication above process, Generate sequence up jar. 2.Operating principle of down jar The loosen load of down jar lock can be transfer as per in demand .There are a certain ratio between up locking force and down locking force , and the ratio is adjustable. If down jar, fed off drilling tool until pressure reach to down locking force, jar should generate down jar force. If need to repeat jar, lifting drilling tool to anew securing position repeat above process.
1.Description: The mechanical-hydraulic drilling jar is a jarring and stuck releasing tool. It integrates the up jar and down jar and can release the stuck accident occurring during drilling operation. The drilling jar is an ideal tool for directional well and deep well drilling. Operating principle 1.Operating principle of up jar Lifting drilling tool, slip assembly which bear the acting of dish reed elastic force and slip locking force compels latch mechanism of slip clasp slip mandrel. While slip mandrel up run with mandrel to overcome slip locking force and damping action between hydraulic valve assembly and spindle extension, jar Make drill stem accumulate energy, delay time. When mandrel up run to the state of release constraint, elastic potential energy accumulated in drill stem will convert to upward kinetic energy, generate up jar. If need sequence up jar, you need fed off drilling tool till relock latch mechanism, reduplication above process, Generate sequence up jar. 2.Operating principle of down jar The loosen load of down jar lock can be transfer as per in demand .There are a certain ratio between up locking force and down locking force , and the ratio is adjustable. If down jar, fed off drilling tool until pressure reach to down locking force, jar should generate down jar force. If need to repeat jar, lifting drilling tool to anew securing position repeat above process.
Precision roto moulds The mould art has all tooling facilities and skilled team of mold makers for precision fabricated moulds. The quality surface finish and tolerance on a rotationally moulded part are mostly dependent upon the quality and precision mould. We fabricated and cast all kinds of rotational moulds of various kinds of rotational moulding products, which are highly demanding in the market. Sheet metal mould fabrication procedure: Data collection of the product Preparation of mould design on cad Cutting of sheet Bend of shape of mould parts Assembly of mould parts on working table Tig welding Grinding and polishing of the mould Inspection of mould and dents removal Mould frame and mould clamps welding Finishing and polishing of moulds Final inspection of the mould
Best quality api 7-1 standard and sprial drill collar Product description Drill collar is the basic component in the bha which provide weight on the bit for dirlling and keeps the drill string in tension.Drill collar is manufactured from aisi 4145h modified quenched and tempered steel and is heat treatment along its entire length for uniform toughness and durability. Srict netallurgical test are performed pre specifications to ensure that the heat treatment produces consisitent and maxium hardness through the depth of the bar. Feartures and benefits: 1. Hardness rannge of 285 to 341 bhn and a charpy impact value of 40ft/lbs are guaranteed for evenly distributed 16 points in any cross sections at room temperature 2.Connections ar phosphate coated afther machinning to protect the threads from corrosive elements and to prevent galling upon initial make -up Thread roots are cold rolled on api and h0-90 connections 3.Pressed steel thread protectors are supplied fo all drill collar that are equipped with standard connection
Best quality pneumatic soft seal butterfly valve used in oil and gas Product description Butterfly valve is closed a disc, around the axis of rotation to achive a valve open and close, in the tube on the main cuttring and throttling. Opening and closing is a disc-shiped buttefly plate, the body is around its own axis rotation turn, so as to achieve the aim of opening and closing or adjust. Buttefly valve fully open to the barrier is usually less than 90â°c, butterfly valve and the adjusment rod itself-locking ability, for the sake of the butterfly plate positioning, to add worm gear reducer on the valve stem, the use of worm gear reducer, can not only make the butterfly plate with self-locking ability. Make the butterfly plate to stop at any position, can also improve the operating performance of the valve. Model of products: D371f-16c D: valve code: d butterfly valve. 3: driver code: handle-drive, two screw-link transmission, 3 worm transmission, 6 pneumatic, 9 electric. 7: link forn code: 4 flange, 7pairs of folders. 1. Structure of the code: 0 the center line, a vertical plate, two pairs of eccentric, 3 triple eccentric. F:sealing material: x-nbr, xe-epdm, , xsi slicone rubber, xt fluorine rubber, xt special rubber, f ptfe 16: nominal pressure: pn0.6-16mpa. C: body material: ht200 cast iron, c carbon steel, q-iron.
Lowest price API 7-1 non magnetic spiral drill collar Product Description Drill Collar is the basic component in the BHA which provide weight on the bit for dirlling and keeps the drill string in tension.Drill collar is manufactured from AISI 4145H modified quenched and tempered steel and is heat treatment along its entire length for uniform toughness and durability. Srict netallurgical test are performed pre specifications to ensure that the heat treatment produces consisitent and maxium hardness through the depth of the bar. Feartures and benefits: 1. hardness rannge of 285 to 341 BHN and a charpy impact value of 40ft/lbs are guaranteed for evenly distributed 16 points in any cross sections at room temperature 2.Connections ar phosphate coated afther machinning to protect the threads from corrosive elements and to prevent galling upon initial make -up Thread roots are cold rolled on API and H0-90 connections 3.Pressed steel thread protectors are supplied fo all drill collar that are equipped with standard connections
Application instruction: Keito: Coating: a14/a43 63 bronze colored .Machine the semi finishing and finishing stainless steel; hardened steel;hrc45-64 chilled steel; titanium alloy; high nickel content alloy
Application instruction: KEITO: COATING: A14/A43 64 stainless steel; medium and low processing the material below HRC 45.
Application instruction: Keito: Coating: a14/a43 67 gravity milling; semi finish and finish turning; carbon steel; rough processing of stainless steel
Application instruction: Keito: Coating: a14/a43 63 bronze colored .Machine the semi finishing and finishing stainless steel; hardened steel;hrc45-64 chilled steel; titanium alloy; high nickel content alloy.
Application instruction: KEITO: COATING: A14/A43 68 high speed turning processing; cast processing; high speed milling processing; rough turning; gravity cutting;
Application instruction: KEITO: COATING: A14/A43 69 rough turning; gravity turning; deep cut milling
Application instruction: Keito: Coating: a14/a43 63 bronze colored .Machine the semi finishing and finishing stainless steel; hardened steel;hrc45-64 chilled steel; titanium alloy; high nickel content alloy.
Casing pup joint &tubing pup joint Drilling tool Api 5ct tubing pup joint
