BW-250 mud pump is a horizontal triplex single-acting piston pump.For this drilling pump.two cylinder diameters and four shifts of speed are available.Triplex mud pump with large cylinder diameter (80mm) is applicable for large-diameter drilling machine, while pump with small cylinder diameter (65mm) is suitable for small-diameter drilling machine.Both of the mud pumps enjoy four shifts of displacement and suite well for different hole depths and diameters.This drilling pump is also perfect for cement mortar grouting with the water cement ratio reaching 1:1. The drilling fluid used by this reciprocating piston pump shall not contain any chemical impurities that are corrosive to metals and rubber parts. When using mud for flushing, the recommended proportion of water and mud is between 1.03 and 1.12, viscosity of mud between 18 and 25S, silt content lower than 4%, diameter of sand particles not exceed 3mm, and PH value around 7 to 8. No tiny mud balls, weeds, leaves and other impurities are allowed in themud. With sophisticated structure and new materials in China and abroad, small volume and light weight, easy assembly and disassembly as well as long service life of high wear parts, this mud pump enjoys superior performance.
Stainless steel drilling bitProducts Description:Application domain:for implantologyMaterial:Ultra high rust-proof and high wear-resistant stainless steel, ceramicLZQ is an OEM factory for all kinds of dental implant drills, such as Ceramic Drill, Drill with Inner Irrigation, Wrench, Screwdriver, Bone Fetcher, etc.We can produce with super hard and super finish grinding and satisfy your requirement of any type of shank, web thickness, width of chip flute,land, drill tip,inner cooling hole, structure of cutting edge, angle of cutting edge, degree of sharpness of cutting edge, and the dimension tolerance can be up to ±0.003mm 3m.adopt 6 axis 5 motion CNC grinding center(AA) fine grinding to micro conical drill, with high concentricityand high sharpness.Minimal Bone Removing bone deletion of Apex can be minimized (taper drill). Almost no bone necrosis due to overheating followed by over-deletion on the apex. Bone trauma is minimized due to significantly low amounts of bone loss. Bone can be preserved by slow drilling.(300rpm)(Ultra-high wear-resistant stainless steel A)(hardened HRC64±2 Section)Rust-proof, ultra-high wear-resistant stainless steel of conventional standard, with ultra-high wear resistance (ultra-high hardness) performance and conventional standard rust prevention, corrosion resistance, with 2~3 times longer lifetime comparing with that of the general stainless steel, and could make the cutting edge cutting sharpness last for a super-long time.alloy drill bit, bone drill bi
Model BW850/5 water well mud suction pump Type Horizontal double cylinder reciprocating double action piston pump Cylinder diameter (mm) 260 Stroke (mm) 66 Pump speed (times/min) 140 130 95 Flow (l/min) 850 600 350 Pressure (Mpa) 5 6 8 Power (Kw) 90 Shape size (mm) 3018*1120*2050 Weight (kg) 3100
The BW320 Triplex Single Acting Reciprocating Piston Mud Pump is a horizontal single-acting reciprocating mud pump with three cylinders. It has two cylinder diameters, four changeable gear speeds and eight flows can be chosen. It can support for the hydraulic impact drilling for the hole depth within 1000 meters, the screw drilling or turbine drilling for the hole depth within 1500 meters and geological core drilling for the hole depth of 2500 meters. Model BW320 Type Horizontal, Single-acting, Reciprocating, No. of Cylinders 3 Stroke 110mm Cylinder Diameter 80mm 60mm
Pruducts Name: Indexable Drilling Insert, SPGT-PM Group of Product: ISO Drilling Tools , Indexable Drilling Inserts Usage Metal Drilling Material Tungsten Carbide Typ: SPGT-PM Brand Name HAFFMAN Place of Origin China Pruducts Name Indexable Drilling Insert, SPGT-PM Materials of Workpiece all kinds of materials Insert Shape 90 Clearance Angel 11 Inserts Dimension 050204,060204,07T308,090408,110408,140512 Using Face Single Face Chip Breaker PM Stock on Stock Package Plastic Box FOB Reference Price: US $1-4 / Pieces | 10 Piece/Pieces (Min. Order) Delivery Time: 1- 30 days, on stock Port: FOB Shanghai Supply Ability: 100, 000 Pcs pro month
Drilling Rig Drilling diameter(mm) 75,91,110,130,150,300 Drilling depth (m) 180,150,100,70,50,30 Drill pipe diameter (mm) 42,50 Drilling angle(�°) 90~75 Equipment size(L * B * H) 1750 * 780 * 1273 (mm) Rig weight (except engine) 595 Gyrator Spindle speed (four gear) (r/min) 71,182,310,790 Spindle maximum feed pressure(KN) 15 Spindle maximum lifting force(KN) 25 Spindle maximum output torque(KNâ?¢ m) 1.5 Winch assembly Winch maximum lifting force (single rope) 20 Reel speed (r/min) 20,39,85,170 Reel circumferential speed(m/s) 0.172,0.345,0.738,1.476 Reel diameter(mm) 140 Wire rope diameter(mm) 9.3 Wire rope density (m) 40 Brake diameter(mm) 278 Brake band width (mm) 50 Water pump Pump type Horizontal single cylinder double acting Maximum displacement (motor)(L/min) 95(77) Work pressure (Mpa) 1.2 Cylinder diameter (mm) 80 Piston stroke(mm) 100 The maximum allowable pressure (Mpa) 1.2 Oil pump Oil pump type YBC -20/125 Nominal pressure (Mpa) 12.5 Rated flow(ml/r) 20 Rated speed(r/min) 800-1500 Diesel engine or motor Diesel engine ZS 1115 Rated power (KW) 16.2 Rated speed (r/min) 2200 Rated pressure(Mpa) 11 Motor type Y160 - 4
Applications of XY-150 hydraulic core drilling rig ·geological survey ·geophysical exploration ·road and high-rise building foundation exploration ·water wells ·blasting holes and other drilling projects 2. Parameters of XY-150 hydraulic core drilling rig Drilling depth(m) 150 Maximum opening diametermm 219 The final hole diametermm 73 Rod diametermm 42/50 Spindle speed (r/min) 140/295/470/790/1010 Spindle strokemm 450 Hoisting capacity (kn) 14 Steel wire diametermm 9.3 Maximum pressure (mpa) 1.2 Working pressure (mpa) 0.7 displacementl/min 150 Hydraulic pump pressure (mpa) 1.2 Hydraulic pump rotation speed (r/min) 1800 Matched driving power (diesel engine and motor) S1105 diesel engine and 11kw motor
1.Brief introductions of KQZ-180D pneumatic-electric DTH drilling rig KQZ-180D pneumatic-electric DTH drilling rig is suitable for drilling and geothermal drilling. It has many advantages, such as large diameter, deep drilling, fast footage, flexible movement and wide application area. 2.Specifications of KQZ-180D pneumatic-electric DTH drilling rig KQZ-180D Borehole diameter mm 100-219 Borehole depth m 150 Drilling angle ° 45-90 One-time feed stroke mm 1500 Motor power kw 7.5 Rotating speed of drilling tools rpm 0-78 Air pressure mpa 0.8-2.1 Air consumption l/min 13-21 Weight kg 600
1.Brief introductions of ZDY-2300 full hydraulic tunnel drilling rig The ZDY2300 hydraulic tunnel drilling rig for coal mine is one of ZDY series drilling rig developed by our company. The drilling rig adopts hydraulic transmission mechanism. It has large drilling ability, fast speed, simple operation. And also it is stable and reliable and convenient to transport and install. It can solve the problems of jetting hole, hole collapse, drilling jam and so on in the process of drilling in soft outburst coal seam. 2.Applications of ZDY-2300 full hydraulic tunnel drilling rig ZDY-2300 full hydraulic tunnel drilling rig is mainly used for drilling holes of gas pumping (row),grouting hole, water injection hole, anti process and pressure relief hole, geological exploration hole and other engineering drilling holes 3.Specifications of ZDY2300 full hydraulic tunnel drilling rig Item Unit Model ZDY-2300 Drilling rig main engine Drilling depth m 300 Open hole diameter mm 94/115/133 End hold diameter mm 94 Drilling pipe diameter mm 63 Drilling angle -90-+90 Output rotating speed r/min 70/160 Output torque nm 2300/1000 Thrust kn 110 Pulling force kn 80 Rated advance speed m/min 0-1.5 Feeding stroke mm 850 Dimensions mm 2240*1000*1450 Weight kg 1400 no drill rod Pumping station Setting work pressure (for small pump) mpa 16 Setting work pressure (for large pump) mpa 16 Working medium 46 antiwear hydraulic oil Effective tank capability l 110 Dimensions mm 1685*800*840 Weight kg 616 Control station Rotating pressure (inversion) mpa 15 Rotating pressure (corotation) mpa 14 Propelling pressure mpa 13 Dimension mm 1140*615*1130 Weight kg 175 Electric motor model YBK2-225S-4 power kw 37 voltage v 380/660 current a 69.9/40.4 rotating speed r/min 1480 Total Weight kg 2200
1.Brief introductions of ZDY-650 full hydraulic tunnel drilling rig The ZDY-650 full hydraulic tunnel drilling rig is mainly used for drilling holes, grouting holes. The working area is more than 6.5 square meters, and the height is more than 2.3m. The width is more than 2.8m. It has two kinds of drills, which are split column rack and pedestal rack. It can choose different drilling rig according to the height and usage of underground roadway. 2.Specifications of ZDY-650 full hydraulic tunnel drilling rig Project Unit ZDY-650 Maximum drilling depth m 150 Open hole diameter mm 75/115 End hole diameter mm 65 Drilling pipe diameter mm 42 Drilling angle �° 0-�±90�° Output rotating speed r/min 95 Output torque n.m 650 Feeding force kn 48 Pullout force kn 35 Rated advance speed m/min 0-1.5 Feeding stroke mm 850 Hardness range (protodyakonov scale of hardness) / fâ?¤8 Noise db(a) â?¤92 Working efficiency % â?¥40 Main engine dimension(long * weight * high) mm 2200*600*500 Total weight (excluding drill rod) kg 1200 Pumping station pump discharge pressure mpa rotation 14/ feed 11 working medium / 46# Antiwear hydraulic oil tank capacity l 96.6 dimension (long *wide*high) mm 1480*700*650 Control station feeding pressure mpa 11 reverse rotation pressure mpa 13 forward rotation pressure mpa 12 dimension (long *wide *high) mm 500*400*450 Motor model / YBK2-160L-4 rated power kw 15 rated voltage v 380/660 660/1140 rated current a 30/17.5 17.5/10.1 rated rotating speed r/min 1460 Two layer steel wire braided hydraulic support rubber tube assembly RB2-6/10/13/16/19/22/25/32
1.Brief introductions of KQZ-200D pneumatic-electric DTH drilling rig KQZ-200D pneumatic-electric DTH drilling rig is suitable for drilling and geothermal drilling. It has many advantages, such as large diameter, deep drilling, fast footage, flexible movement and wide application area. 2.Specifications of KQZ-200D pneumatic-electric DTH drilling rig KQZ-200D pneumatic-electric DTH drilling rig Borehole diameter mm 100-254 Borehole depth m 200 Drilling angle 45-90 One-time feed stroke mm 1500 Motor power kw 11 Diesel engine power hp 8.5 Rotating speed of drilling tools rpm 52 Air pressure mpa 1.45-2.5 Air consumption l/min 15-27 Total weight kg 650
1.The applications of FY300 crawler pneumatic water well drilling rig civil engineering drilling geothermal drilling, drilling with large diameter and deep drilling footage Its fast, flexible and efficient 2.The specifications of FY300 crawler pneumatic water well drilling rig Model FY300 Gross weight t 8.8 Dimension mm 4350*1850*2750 Aperture mm 140-325 Drilling depth m 300 Feed stroke mm 6000 Travel speed km/h 2 Grade ability max. 30 Rising height from ground mm 230 Wind pressure mpa 1.7-3.3 Air consumption m³/min 23 Engine power kw 85 Rotary speed rpm 55-115 Rotation torque n.m 7200-8500
1.The brief introductions of KQZ-200D pneumatic water well drilling rig KQZ-200D pneumatic water well drilling rig is suitable for drilling and geothermal drilling. It has many advantages, such as large diameter, deep drilling, fast footage, flexible movement and wide application area. 2.The specifications of KQZ-200D pneumatic water well drilling rig KQZ-200D pneumatic water well drilling rig Borehole diameter mm 100-254 Borehole depth m 200 Drilling angle �° 45-90 One-time feed stroke mm 1500 Motor power kw 11 Diesel engine power hp 8.5 Rotating speed of drilling tools rpm 52 Air pressure mpa 1.45-2.5 Air consumption l/min 15-27
HP shank (ISO 104), diameter 2.35mm (3/32"), suitable to all low speed handpiece More than 50 types of nail carbide burs for choices, most popular shapes are included. They must satisfy all your applications of nail beauty and podiatry. Different kinds of cutter types range from super coarse cutters to coarse cutters, medium cutters, fine cutters and extra fine cutters. Special kits of nail treatment are OEM available by your special demands.
1.The applications of FY260 crawler pneumatic water well drilling rig ·civil engineering drilling ·geothermal drilling, ·drilling with large diameter ·deep drilling footage ·fast, flexible and efficient. 2.The specifications of FY260 crawler pneumatic water well drilling rig Model FY260 Gross weight t 6.2 External dimension mm 3900*1950*2550 Aperture mm 140-325 Drilling depth m 260 Feed stroke mm 3000 Travel speed km/h 2.5 Grade ability max. 30° Rising height from ground mm 250 Wind pressure mpa 1.7-3.0 Air consumption m³/min 17-35 Engine power kw 85 Rotary speed rpm 40-70 Rotation torque n.m 7000-9000
Product Description: ST-200 model crawler-mounted drilling rig is equipped with BW-250 mud pump. Its triplex mud pump. Have high pressure and large discharge, its adapt to the big diameter and depth holes drilling. The main machine equipped with shift device, fore-and-aft movement by itself, convenient for operate. Main winch and minor winch drive by hydraulic system, they are installed on the main drilling machine. Compact in frame. Its adapted to the wire line coring drilling. The machine is mainly used for water well, wire-line coring drilling, geothermic well, general investigation and exploration. Road and tall building ground drill exploration and other foundation working.
RMT 1210 SVR model comes with "silencer" and "Vibration Reduced" Handle. With its new back head design and new muffler, the RMT 1210 SVR combines excellent performance in its weight class with good ergonomics. Lowering the vibration levels offers immense benefits to the operator. They do not tire easily so it increases their productivity. Reduced vibration levels also control its negative effects on operators. It is an upgraded version of RMT 1210. Model # RMT 1210 SVR Weight with silencer 24.5 kg 55 lb Length 600 mm 24" Air pressure 6 bar 87 psi Air consumption 26.5 l/s 56 cfm Blows per minute 1400 Air inlet 19 mm 3/4" Shank size (standard) - 8900 0030 06 25 x 108 mm 1" x 4�¼â?? Shank size (option 1) - 8900 0030 08 28 x 160 mm 1�¹â??8â?³ x 6�¼â?? Shank size (option 2) - 8900 0030 10 32 x 160 mm 1�¼â?? x 6�¼â?? Retainer type Latch
KB45 Mud Pump Pulsation Dampener Assembly Installation position:Air chamber is installed at one end of the discharge pipe in the hydraulic end Function:play a role of stabilizing the pressure and pressure compensation. Working pressure: 80% of the mud pump. 1.Disassembling and assembling air bag must first relief. 2.F500/F800 mud pump using KB45 air chamber, F1000/1300/1600 mud pump using air chamber KB75. 3.Air chamber play an important role in drilling to reduce the fluctuations and stable pressure ,so in drilling production, maintaining the normal operation of the air bag is very important . The maintenance of the air bag (1).Air bag inflator pressure is 30% of designed pump pressure, the general pressure is 4~6MPa , the best pressure is 4.5MPa (2) .Mud pump at the normal working hours, the air bag cutoff valve is closed to protect gauges
Drilling Line Spooler is a special equipment for the working wireline retracting of crown block and traveling block of drilling rig(also available for retracting tool of similar principle).Because it is equipped with a lead line drum, it can complete the line string up work before drilling and retracting line when finished drilling. Work is more convenient and safe, easy to operate. Classification: Electric, Pneumatic, Hydraulic. Loading: 8Ton, 15Ton, 18Ton. Customizable.
Shale shaker is primary solid control equipment in the drilling fluid purification system.which is used to separate the large particle cuttings contained in the drilling fluid, and the treated smaller particle drilling fluid can be passed to the next stage of solid control equipment for further processing. Shale shaker is the prerequisite for ensuring the normal operation of the latter stages of solid control equipment. If the shale shaker can not work normally, the latter stages of solid control equipment will be overloaded with work,seriously affect the work effect, caused the performance of the drilling fluid to deteriorate, aggravate the wear of drilling pump cylinder liners, pistons, drill bits, water passage, etc and thereby increasing the pump repair time,it is easy to cause complicated underground conditions. Therefore, shale shaker are important for improving drilling fluid performance and reducing drilling costs.
