1.Brief introduction of QZ-2A three phase electric sampling drilling rig QZ-2A is a three phase electric sampling drilling rig , produced by Shandong Master Machinery Group Co.,Ltd. It is suitable for industrial and civil buildings, bridges, railways, roads, utilities and other sectors of the geological exploration. 2. Technical parameters of QZ-2A three phase electric sampling drilling rig QZ-2A three phase electric sampling drilling rig Borehole diameter (mm) 32-91 Drilling depthm soil9110-15m stone915-10m stone7510-15m stone6015-20m stone4620-25m Drilling pipe diameter (mm) 28 Rotate speedr/min 185-380 Torquen.m 80 Powerkw 3 Dimensionl*w*h 600*450*1900 Weightkg 95 3. Configuration list of QZ-2A three phase electric sampling drilling rig Item Parameter Unit Quantity Three phase electric sampling drilling rig QZ-2A platform 1 Drilling pipe 28*1500 pc 6 Drilling pipe 28*800 pc 8 Drilling joint 35 pc 14 Reducing nipple 45/35 pc 1 Core barrel 45*800 pc 1 Alloy bit 46 pc 1 Reducing nipple 58/35 pc 1 Core barrel 58*800 pc 1 Alloy bit 60 pc 1 Three-wing bit 0 pc 1 Safety clamp hold 1 Water seal Y30*50*10 pc 4 Oil seal 17*50*10 pc 2 Control wheel set 1
1. Purpose of HZQ-20 gasoline engine concrete core drilling rig HZQ-20 gasoline engine concrete core drilling rig adopts high-speed cutting technology and is matched with thin-walled diamond drills. It is widely used in drilling and coring in engineering construction, municipal engineering, equipment installation engineering and building quality inspection. On the concrete, asphalt pavement and limestone roads such as highways, airports, ports and dams, the cores are subjected to compression and flexural tests. The coring and open hole is used to drill anchor bolt hole for large-scale machine equipment, and bridge handrails and traffic safety protection. 2. Features of HZQ-20 gasoline engine concrete core drilling rig Double column structure and spiral feeding mode are adopted with good stability and simple operation and labor saving. The rig is equipped with wheel, which is easy to move. The use of high-speed cutting technology and thin-wall diamond drill supporting can drill and cut high strength reinforced concrete with high drilling efficiency, accurate hole location, hole wall smooth, good hole quality, complete core smooth, small vibration, no damage to the building. 3.Parameters of HZQ-20 gasoline engine concrete core drilling rig ·Drilling diameter: 200mm (if larger hole size is needed, please specify) ·Drilling depth: 700mm (greater depth can be drilled with connecting rod or extended mandrel) ·Engine: gasoline engine ·Power: 5.5 HP, 9.0 HP, 13 HP and 20 HP ·Output speed: 800-1500 RPM ·Weight: 180KG Shandong Master Machinery Group specializes in the supplying of concrete drilling and coring machine. The main models are HZQ-20 gasoline engine concrete core drilling rig, HZC-20 diesel engine concrete core drilling rig, HZQ-20T towed concrete core drilling rig.
1.Brief introductions of QZ-1A two phase electric sampling drilling rig QZ-1A is a two phase electric sampling drilling rig produced by Shandong Master Machinery Group Co.,Ltd. It is suitable for all kinds of geological exploration, like industrial and civil buildings, bridges, railways, roads and so on. QZ-1A two phase electric sampling drilling rig is only 80kg; height is less than 2 meters, and the drilling rig can been break down structure. Hence it is easy to move and operated. 2.Technical parameter s of QZ-1A two phase electric sampling drilling rig QZ-1A two phase electric sampling drilling rig Borehole diameter (mm) 32-46 Drilling depth (m) Soil layer: 20-25 Lithosphere: 15-20 Drilling pipe diameter (mm) 25 Rotate speedï¼?r/minï¼? 175 Torque (n.m) 80 Power (kw) 1.5 Dimensions (l*w*h) 600mm*450mm*1900mm Weight (kg) 80 3.Configuration list of QZ-1A two phase electric sampling drilling rig Item Parameters Unit Quantity Two phase electric sampling drilling rig QZ-1A set 1 Drill pipe(mm) 25*1500 pc 6 Drill pipe(mm) 25*800 pc 8 Joint(mm) 32 pc 14 Core barrel(mm) 32*800 pc 1 Alloy bit(mm) 32 pc 1 Reducing nipple(mm) 45/32 pc 1 Core barrel(mm) 45*800 pc 1 Alloy bit(mm) 46 pc 1 Three-wing bit(mm) 60 pc 1 Safety clamp pc 1 Water seal Y Type 30*45*8 pc 4 Control wheel set 1
1. Main Technical Parameters: (1). Model: DU. Size of Slip Bodies: 4 1/2". DP O.D. (in): 2 3/8"; 2 7/8"; 3 1/2"; 4"; 4 1/2". DP O.D. (mm): 60.3; 73.0; 88.9; 101.6; 114.3. (2). Model: DU. Size of Slip Bodies: 5 1/2". DP O.D. (in): 3 1/2"; 4"; 4 1/2"; 5"; 5 1/2". DP O.D. (mm): 88.9; 101.6; 114.3; 127; 139.7. (3). Model: DU. Size of Slip Bodies: 7". DP O.D. (in): 4 1/2"; 5"; 5 1/2"; 6 5/8"; 7". DP O.D. (mm): 114.3; 127; 139.7; 168.3; 177.8. (4). Model: DUL. Size of Slip Bodies: 4 1/2". DP O.D. (in): 2 3/8"; 2 7/8"; 3 1/2"; 4"; 4 1/2". DP O.D. (mm): 60.3; 73.0; 88.9; 101.6; 114.3. (5). Model: DUL. Size of Slip Bodies: 5 1/2". DP O.D. (in): 3 1/2"; 4"; 4 1/2"; 5"; 5 1/2". DP O.D. (mm): 88.9; 101.6; 114.3; 127; 139.7. (6). Model: DUL. Size of Slip Bodies: 7". DP O.D. (in): 4 1/2"; 5"; 5 1/2"; 6 5/8"; 7". DP O.D. (mm): 114.3; 127; 139.7; 168.3; 177.8. (7). Model: SDU. Size of Slip Bodies: 4 1/2". DP O.D. (in): -. DP O.D. (mm): -. (8). Model: SDU. Size of Slip Bodies: 5 1/2". DP O.D. (in): 3 1/2"; 4"; 4 1/2"; 5"; 5 1/2". DP O.D. (mm): 88.9; 101.6; 114.3; 127; 139.7. (9). Model: SDU. Size of Slip Bodies: 7". DP O.D. (in): 4 1/2"; 5"; 5 1/2"; 6 5/8"; 7". DP O.D. (mm): 114.3; 127; 139.7; 168.3; 177.8. 2. Product Description: Drill pipe slip is a kind of handling tools specially used to handle drill pipe during the oil well drilling operations for the exploration of petroleum and natural gas. It is an essential tool for coupling and uncoupling. There are three types of DU series Rotary Slips: DU, DUL and SDU. They are with large handling range and light weight. There into, SDU slips have larger contacting areas on the taper and higher resistance strength. They are designed and manufactured according to API Spec 7K Specification for drilling and well servicing equipment. 3. Features: (1). Suitable for shallow hole drilling, medium depth drilling and deep drilling. (2). 100% customer satisfaction for quality and reliability. (3). After machining all slips undergo 100% inspection. (4). Different types for clients choice for different depth well and different size drill pipe. 4. Material: Carbon Steel. 5. Processing Type: Casting. 6. Machine Type: Drilling Tool. 7. Use: Well Drilling.
1. Main Technical Parameters: (1). Model: DCS-S. Drill Collar O.D. (in): 3-4. Drill Collar O.D. (mm): 76.2-101.6. Weight (kg): 51. Weight (lb): 112. Use in Insert Bowl No.: API or No. 3. (2). Model: DCS-S. Drill Collar O.D. (in): 4-4 7/8. Drill Collar O.D. (mm): 101.6-123.8. Weight (kg): 47. Weight (lb): 103. Use in Insert Bowl No.: API or No. 3. (3). Model: DCS-R. Drill Collar O.D. (in): 4 1/2-6. Drill Collar O.D. (mm): 114.3-152.4. Weight (kg): 54. Weight (lb): 120. Use in Insert Bowl No.: API or No. 3. (4). Model: DCS-R. Drill Collar O.D. (in): 5 1/2-7. Drill Collar O.D. (mm): 139.7-177.8. Weight (kg): 51. Weight (lb): 112. Use in Insert Bowl No.: API or No. 3. (5). Model: DCS-L. Drill Collar O.D. (in): 6 3/4-8 1/4. Drill Collar O.D. (mm): 171.4-209.6. Weight (kg): 70. Weight (lb): 154. Use in Insert Bowl No.: API or No. 3. (6). Model: DCS-L. Drill Collar O.D. (in): 8-9 1/2. Drill Collar O.D. (mm): 203.2-241.3. Weight (kg): 78. Weight (lb): 173. Use in Insert Bowl No.: API or No. 3. (7). Model: DCS-L. Drill Collar O.D. (in): 8 1/2-10. Drill Collar O.D. (mm): 215.9-254. Weight (kg): 84. Weight (lb): 185. Use in Insert Bowl No.: No. 2. (8). Model: DCS-L. Drill Collar O.D. (in): 9 1/4-11 1/4. Drill Collar O.D. (mm): 235-285.7. Weight (kg): 90. Weight (lb): 198. Use in Insert Bowl No.: No. 2. (9). Model: DCS-L. Drill Collar O.D. (in): 11-12 3/4. Drill Collar O.D. (mm): 279.4-323.9. Weight (kg): 116. Weight (lb): 256. Use in Insert Bowl No.: No. 1. (10). Model: DCS-L. Drill Collar O.D. (in): 12-14. Drill Collar O.D. (mm): 304.8-355.6. Weight (kg): 107. Weight (lb): 237. Use in Insert Bowl No.: No. 1. 2. Product Description: Drill Collar Slips are specially developed to handle drill collars during well drilling. There are three types of DCS Drill Collar Slips: S, R, and L. They can accommodate drill collars from 3 in (76.2 mm) to 14 in (355.6 mm) O.D.. The handling sizes can be adjusted by changing the quantity of inserts or slip body. They are designed and manufactured according to API Spec 7K Specification for drilling and well servicing equipment. 3. Features: (1). Multi-segments design make it possible to handle different size drill collars by adjusting the quantity of inserts or slip body. (2). 100% customer satisfaction for quality and reliability. (3). After machining all slips undergo 100% inspection. (4). Different types for clients choice for different depth well and different size drill pipe.
1. Main Technical Parameters: (1). Model: Drill Collar Slips Type A. Drill Collar O.D. (in): 3-4 1/2. Drill Collar O.D. (mm): 76.2-114.3. Use in Insert Bowl No.: API or No. 3. (2). Model: Drill Collar Slips Type A. Drill Collar O.D. (in): 3 1/4-4 3/4. Drill Collar O.D. (mm): 82.55-120.65. Use in Insert Bowl No.: API or No. 3. (3). Model: Drill Collar Slips Type A. Drill Collar O.D. (in): 4 1/4-5 3/4. Drill Collar O.D. (mm): 107.95-146.05. Use in Insert Bowl No.: API or No. 3. (4). Model: Drill Collar Slips Type A. Drill Collar O.D. (in): 5 1/2-7. Drill Collar O.D. (mm): 139.7-177.8. Use in Insert Bowl No.: API or No. 3. (5). Model: Drill Collar Slips Type A. Drill Collar O.D. (in): 6 3/4-8 1/4. Drill Collar O.D. (mm): 171.5-209.55. Use in Insert Bowl No.: API or No. 3. (6). Model: Drill Collar Slips Type A. Drill Collar O.D. (in): 8 1/4-10. Drill Collar O.D. (mm): 209.55-254. Use in Insert Bowl No.: No. 2. (7). Model: Drill Collar Slips Type A. Drill Collar O.D. (in): 10-11 3/4. Drill Collar O.D. (mm): 254-298.45. Use in Insert Bowl No.: No. 2. 2. Product Description: Drill Collar Slips are specially developed to handle drill collars during well drilling. Drill Collar Slips Type A are multi-segments slips. They can accommodate the changes of outer diameter after abrasion of drill collar. They are with light weight, large handling scale and reliable quality. This kind of slips are designed and manufactured according to API Spec 7K Specification for drilling and well servicing equipment. 3. Features: (1). Multi-segments design make it possible to handle different size drill collars by adjusting the quantity of inserts or slip body. (2). 100% customer satisfaction for quality and reliability. (3). After machining all slips undergo 100% inspection. (4). Different types for clients choice for different depth well and different size drill pipe. 4. Material: Carbon Steel. 5. Processing Type: Forging. 6. Machine Type: Drilling Tool. 7. Use: Well Drilling. 8. FAQ: Why you need to choose Lake Petro? As a professional oil and gas service company, Lake Petro has many good experience in selling and serves for the oilfield industries for years. Quality is the culture of the company, we provide API and BV certified products for customer. Can you make us the best quality products as well as a good price? Yes, we can give you really high quality products with competitive price. We have a better understanding in Chinese market, with us your money will be safe. What is special compare with other companies? First, we provide the quality products, with BV and API certified; At the same time, we provide our customer with the best service after sale, any time any where.
1. Main Technical Parameters: (1). Model: WT 4 1/2-6. Drill Collar O.D. (in): 4 1/2-6. Drill Collar O.D. (mm): 114.3-152.4. Weight (kg): 49. Weight (lb): 108. Use in Insert Bowl No.: API or No. 3. Max Load: 40 short tons. (2). Model: WT 5 1/2-7. Drill Collar O.D. (in): 5 1/2-7. Drill Collar O.D. (mm): 139.7-177.8. Weight (kg): 46. Weight (lb): 101. Use in Insert Bowl No.: API or No. 3. Max Load: 40 short tons. (3). Model: WT 6 3/4-8 1/4. Drill Collar O.D. (in): 6 3/4-8 1/4. Drill Collar O.D. (mm): 171.4-209.6. Weight (kg): 42. Weight (lb): 92. Use in Insert Bowl No.: API or No. 3. Max Load: 40 short tons. (4). Model: WT 8-9 1/2. Drill Collar O.D. (in): 8-9 1/2. Drill Collar O.D. (mm): 203.2-241.3. Weight (kg): 39. Weight (lb): 86. Use in Insert Bowl No.: API or No. 3. Max Load: 40 short tons. 2. Product Description: Drill Collar Slips are specially developed to handle drill collars during well drilling. Drill Collar Slips Type WT can accommodate drill collars from 4 1/2 in (114.3 mm) to 9 1/2 in (241.3 mm) O.D.. They are designed and manufactured according to API Spec 7K Specification for drilling and well servicing equipment. 3. Features: (1). Multi-segments design make it possible to handle different size drill collars by adjusting the quantity of inserts or slip body. (2). 100% customer satisfaction for quality and reliability. (3). After machining all slips undergo 100% inspection. (4). Different types for clients choice for different depth well and different size drill pipe. 4. Material: Carbon Steel. 5. Processing Type: Forging. 6. Machine Type: Drilling Equipment. 7. Use: Well Drilling. 8. FAQ: Why you need to choose Lake Petro? As a professional oil and gas service company, Lake Petro has many good experience in selling and serves for the oilfield industries for years. Quality is the culture of the company, we provide API and BV certified products for customer. Can you make us the best quality products as well as a good price? Yes, we can give you really high quality products with competitive price. We have a better understanding in Chinese market, with us your money will be safe. What is special compare with other companies? First, we provide the quality products, with BV and API certified; At the same time, we provide our customer with the best service after sale, any time any where.
1. Main Technical Parameters: (1). Connection: 7 5/8 REG Pin. O.D. (mm): Ï?210. Length (mm): 290. (2). Connection: 6 5/8 REG Pin. O.D. (mm): Ï?190. Length (mm): 280. (3). Connection: NC 50 Pin. O.D. (mm): Ï?155. Length (mm): 270. (4). Connection: NC 46 Pin. O.D. (mm): Ï?150. Length (mm): 270. (5). Connection: NC 38 Pin. O.D. (mm): Ï?115. Length (mm): 260. (6). Connection: NC 31 Pin. O.D. (mm): Ï?100. Length (mm): 210. (7). Connection: 2 3/8 REG Pin. O.D. (mm): Ï?80. Length (mm): 190. (8). Connection: NC 26 Pin. O.D. (mm ): Ï?89. Length (mm): 200. (9). Connection: 3 1/2 REG Pin. O.D. (mm): Ï?100. Length (mm): 220. (10). Connection: 4 1/2 REG Pin. O.D. (mm): Ï?145. Length (mm): 260. (11). Connection: 2 7/8 EUE Pin. O.D. (mm): Ï?80. Length (mm): 220. (12). Connection: 7 5/8 REG Box. O.D. (mm): Ï?230. Length (mm): 290. (13). Connection: 6 5/8 REG Box. O.D. (mm): Ï?200. Length (mm): 280. (14). Connection: NC 50 Box. O.D. (mm): Ï?160. Length (mm): 260. (15). Connection: NC 46 Box. O.D. (mm): Ï?160. Length (mm): 260. (16). Connection: NC 38 Box. O.D. (mm): Ï?120. Length (mm): 270. (17). Connection: NC 31 Box. O.D. (mm): Ï?120. Length (mm): 270. (18). Connection: 2 3/8 REG Box. O.D. (mm): Ï?110. Length (mm): 200. (19). Connection: NC 26 Box. O.D. (mm): Ï?110. Length (mm): 200. (20). Connection: 3 1/2 REG Box. O.D. (mm): Ï?130. Length (mm): 270. (21). Connection: 4 1/2 REG Box. O.D. (mm): Ï?160. Length (mm): 260. (22). Connection: 2 7/8 EUE Box. O.D. (mm): Ï?80. Length (mm): 220. 2. Product Description: Lifting cap is one special tool for lifting of drilling tools in petroleum, natural gas, drilling engineering and geographical exploration, also called as lifting bail. We can provide the lifting cap or lifting bail in integral type or circular type. 3. Features: (1). API certified product with national best quality. (2). Forging type products used for lifting pipe collars, with regular thread connection. (3). Customized products available. (4). Warranty six months after sale. 4. Certification: API. 5. Condition: New. 6. Color: Required. 7. Model: Lifting cap. 8. Place of Origin: China (Mainland). 9. Price FOB in USD: 300~800/Piece(s). 10. Material: Carbon Steel. 11. Processing Type: Forging. 12. Machine Type: Drilling Tool. 13. Use: Well Drilling. 14. Processing Time: 30days. 15. Supply Ability: 10000 pieces/per month. 16. Payment Terms: T/T; L/C; Western Union. 17. Packing & Delivery: (1). Packing Details: Standard Export Package. (2). Port: China Main Port.
1. Main Technical Parameters: (1). Use for product: W-SDS Rotary Slips. Pipe size (in): 2 3/8"~4 1/2". (2). Use for product: W-SDML Rotary Slips. Pipe size (in): 2 3/8"~5 1/2". (3). Use for product: W-SDXL Rotary Slips. Pipe size (in): 3 1/2"~5 1/2". (4). Use for product: 3 1/2~5 Rotary Slips. Pipe size (in): 3 1/2"~5". (5). Use for product: 5~7 Rotary Slips. Pipe size (in): 5"~7". (6). Use for product: W3 1/2"-75 (125) Rotary Slips. Pipe size (in): 2 3/8", 2 7/8", 3 1/2". (7). Use for product: 5-75 (125 200) Rotary Slips. Pipe size (in): 4", 4 1/2", 5". (8). Use for product: DCS-S Drill Collar Slips. Pipe size (in): 3"~4 7/8". (9). Use for product: DCS-R Drill Collar Slips. Pipe size (in): 4 1/2"~7". (10). Use for product: DCS-L Drill Collar Slips. Pipe size (in): 6 3/4"~14". (11). Use for product: WT Drill Collar Slips. Pipe size (in): 4 1/2"~11 3/4". (12). Use for product: 8" Drill Collar Slips. Pipe size (in): 8". (13). Use for product: 9" Drill Collar Slips. Pipe size (in): 9". (14). Use for product: Casing Slips. Pipe size (in): 6 5/8"~30". (15). Use for product: WA-C Safety Clamps. Pipe size (in): 3 1/2"~15 5/8". (16). Use for product: WA-T Safety Clamps. Pipe size (in): 1 1/8"~4 1/2". (17). Use for product: QQ P60-89/585 Pneumatic Spider. Pipe size (in): 2 3/8"~3 1/2". (18). Use for product: QQ P60-89/675 Pneumatic Spider. Pipe size (in): 2 3/8"~3 1/2". (19). Use for product: QQ P60-127/900 Pneumatic Spider. Pipe size (in): 2 3/8"~5". (20). Use for product: Well Repair Manual Tongs. Pipe size (in): 2 3/8"~10 3/4". (21). Use for product: B Manual Tongs. Pipe size (in): 2 3/8"~12 3/4". (22). Use for product: DB Manual Tongs. Pipe size (in): 3 1/2"~17". (23). Use for product: 13 3/8 Casing Manual Tongs. Pipe size (in): 13 3/8". (24). Use for product: Q13 3/8-30 Casing Manual Tongs. Pipe size (in): 13 3/8"~30". (25). Use for product: Tubing and Workover Tongs. Pipe size (in): All size available. (26). Use for product: Drill Power Tongs. Pipe size (in): All size available. 2. Features: (1). The dies made from high-quality alloy steel in our company. (2). The dies are chemically heat-treated for surface hardness. (3). The dies and slip inserts are wear-raciting, corrosion-resistance. (4). Customized products are available. (5). Qualified API certified manufacture.
1. Main Technical Parameters: (1). Connection: 7 5/8" REG Pin. O.D. (mm): 210. Length (mm): 290. (2). Connection: 6 5/8" REG Pin. O.D. (mm): 190. Length (mm): 280. (3). Connection: NC 50 Pin. O.D. (mm): 155. Length (mm): 270. (4). Connection: NC 46 Pin. O.D. (mm): 150. Length (mm): 270. (5). Connection: NC 38 Pin. O.D. (mm): 115. Length (mm): 260. (6). Connection: NC 31 Pin. O.D. (mm): 100. Length (mm): 210. (7). Connection: 2 3/8" REG Pin. O.D. (mm): 80. Length (mm): 190. (8). Connection: NC 26 Pin. O.D. (mm): 89. Length (mm): 200. (9). Connection: 3 1/2" REG Pin. O.D. (mm): 100. Length (mm): 220. (10). Connection: 4 1/2" REG Pin. O.D. (mm): 145. Length (mm): 260. (11). Connection: 2 7/8" EUE Pin. O.D. (mm): 80. Length (mm): 220. (12). Connection: 7 5/8" REG Box. O.D. (mm): 230. Length (mm): 290. (13). Connection: 6 5/8" REG Box. O.D. (mm): 200. Length (mm): 280. (14). Connection: NC 50 Box. O.D. (mm): 160. Length (mm): 260. (15). Connection: NC 46 Box. O.D. (mm): 160. Length (mm): 260. (16). Connection: NC 38 Box. O.D. (mm): 120. Length (mm): 270. (17). Connection: NC 31 Box. O.D. (mm): 120. Length (mm): 270. (18). Connection: 2 3/8" REG Box. O.D. (mm): 110. Length (mm): 200. (19). Connection: NC 26 Box. O.D. (mm): 110. Length (mm): 200. (20). Connection: 3 1/2" REG Box. O.D. (mm): 130. Length (mm): 270. (21). Connection: 4 1/2" REG Box. O.D. (mm): 160. Length (mm): 260. (22). Connection: 2 7/8" EUE Box. O.D. (mm): 80. Length (mm): 220. 2. Product Description: Lifting cap is one special tool for lifting of drilling tools in petroleum, natural gas, drilling engineering and geographical exploration, also called as lifting bail. We can provide the lifting cap or lifting bail in integral type or circular type. 3. Features: (1). API certified product with national best quality. (2). Forging type products used for lifting pipe collars, with regular thread connection. (3). Customized products available. (4). Warranty six months after sale. 4. Certification: API. 5. Condition: New. 6. Color: Required. 7. Model: Lifting cap. 8. Place of Origin: China (Mainland). 9. Material: Carbon Steel. 10. Processing Type: Forging. 11. Machine Type: Drilling Tool. 12. Use: Well Drilling. 13. Processing Time: 30 days. 14. Supply Ability: 10000 pieces/per month. 15. Payment Terms: T/T; L/C; Western Union. 16. Packing & Delivery: (1). Packing Details: Standard Export Package. (2). Port: China Main Port.
1. Main Technical Parameters: (1). No. of Latch Lug Jaw: 1#. Size Range: 2 3/8"~3 1/2" (60.3~88.9 mm). Rated Torque (kN*m): 27. (2). No. of Latch Lug Jaw: 2#. Size Range: 2 7/8"~4 1/4" (73~108 mm). Rated Torque (kN*m): 27. (3). No. of Latch Lug Jaw: 3#. Size Range: 4"~5 3/4" (101.6~146.1 mm). Rated Torque (kN*m): 27. (4). No. of Latch Lug Jaw: 4#. Size Range: 5 3/4"~7" (146.1~177.8 mm). Rated Torque (kN*m): 20. (5). No. of Latch Lug Jaw: 5#. Size Range: 7 1/4"~8 5/8" (184.2~219.1 mm). Rated Torque (kN*m): 20. (6). No. of Latch Lug Jaw: 6#. Size Range: 9 5/8"~10 3/4" (244.5~273.1 mm). Rated Torque (kN*m): 14. 2. Product Description: Manual tongs are necessary tools applied to make up and break out pipes. Changing lug jaws and latch steps can adjust different handling sizes of the tongs. They are designed and manufactured according to API Spec 7K Specification for drilling and well servicing equipment. Q2 3/8"~10 3/4"--27 Type WWC Manual Tong Type WWC Manual Tong is an essential tool in oil operation to fasten or remove the screws of drill pipe and casing joint or coupling. The handling size of manual tong can be adjusted by changing latch lug jaws and latch steps. The available range of manual tong is from 2 3/8~10 3/4 inch. 3. Features: (1). API 7K certified quality assured. (2). Easy to operation to holding different size by changing the lug jaw. (3). Spare parts available after sales, all parts are traceable. (4). Size range from 2 3/8"~10 3/4". (5). Rated torque range from 14kN·m to 27kN·m. 4. Certification: API 7K. 5. Condition: New. 6. Color: Required. 7. Place of Origin: Shandong, China (Mainland). 8. Minimum Order: 1 Set. 9. Material: Carbon Steel. 10 Processing Type: Forging. 11. Machine Type: Drillnig Tool. 12. Use: Well Drilling. 13. Processing Time: 20 days. 14. Supply Ability: 400 sets / per month. 15. Payment Terms: T / T; L / C; Western Union. 16. Packing and Delivery: (1). Packing Details: Standard Export Package. (2). Port: China Main Port.
TQ Series Hydraulic Casing Tong Product Description TQ series of casing power tongs are widely used for making up and breaking out pipes or casinga in diameters of 4~13 3/8 inch. the tong heads are designed "open"type and can freely clamp and escape from the casing.TQ casing power tongs are safe, raliable and easy to handle with mobility.this series of tongs can be connected to computer controlling units and can serve as ideal well mechnical tool for surface operations in oil fields. national invention patent of the tongs has been got. the tongs are designed and manufactured according to API 7K specification for drilling equipment. TQ series of hydraulic casing tongs are widely used for making-up and breaking-out of casings or pipes. The series of casing tongs are wholly hydraulic driven. The tongs are configured with a large-torque motor. And per form mechanical gearchange. Structure is simple and operation is safe. The casing tongs can be supplied with torque device to perform computer monitoring and managing on pressure, torque and rounds. The casing tong are designed and manufactured according to SY/T5074 standard and API spec 7Kspecification for drilling and well servicing equipment. Products Drawing TQ Series Hydraulic Casing Tong Main Parameters Casing Power tongs Technical specification: Model TQ178/16 TQ340/35 TQ356/55 Size Range mm 101.6-178 114.3-340 114.3-356 inch 4-7 4 1/2 - 13 3/8 4 1/2 - 14 Max Pressure Mpa 18 16.6 psi 2610 2400 Working flow L/min 110-160 110-140 gpm 29.3-42.7 29.3-37.3 Air Pressure Mpa 0.5-0.9 psi 72-130 Max. Torque kN.m 16 35 55 ft.lbf 11800 25800 40560 Speed rpm 9-79 3.5-86 4-70 Size mm 1450*760*740 1580*900*880 1770*960*850 in 57*30*29.1 62.2*35.4*34.6 69.7*37.8*33.5 Weight Kg 580 780 1150 lb 1280 1720 2530 TQ series hydraulic casing power tongs technical specification: Model TQ178/16Y TQ340/35Y TQ356/55Y TQ508/70Y TQ610/60Y TQ340/85Y Size rang mm 101.6-178 114.3-340 114.3-365 244.5*508 244.5-610 114.3*340 inch 4-7 4 1/2 - 13 3/8 4 1/2 - 14 9 5/8 -20 9 5/8-24 4 1/2-13 5/8 Max. Pressure Mpa 18 20 18 psi 2610 2900 2610 Working Flow L/min 110-160 110-170 120-180 110-170 gpm 29.3-42.7 29.3-45.4 32-48 29.3-45.4 Max.Torque kN.m 16 35 55 70 60 85 ft.lbf 11820 25800 40560 51600 44250 62680 Speed rpm 9-79 8-90 4.8-61 4-43.6 5-45 3.2-45 Size mm 1500*760*800 15800*900*860 1770*960*780 2080*1280*760 2330*1310*840 1995*1150*680 inch 59*30*31.4 62.2*35.4*33.8 69.7*37.8*30.7 82*50.4*30 91.7*51.6*33 78.5*45.3*26.8 Weight Kg 560 760 1100 1550 2100 1700 lb 1230 1670 2420 3410 4620 3740
Features: 19" standard dimension suitable for all type cabinet Convenient for installation, remove and additio Convenient with sliding rail MPO/MTP trunk lines connecting port is fixed on the back of cassette Transmission for Single MPO/MTP connecter above 40G or 100G High Density:1pc MPO /MTP cassette can reach 24cores High Capacity:1pc MPO/MTP ODF(4U) with 24pcs cassette;Maximum:576cores High Capacity:1pc MPO/MTP ODF(2U) with 12pcs cassette;Maximum:288cores High Capacity:1pc MPO/MTP ODF(1U) with 6pcs cassette;Maximum:144cores Save manpower:No need tidy on site as the ODF assembly
Name: Mud agitator Application: mixer fluid to escape the sediment Using place: on the mud tank Motor: Explosion-proof, from 5.5KW to 22KW Reduction gear: cycloid pin type Shaft: 89mm diameter Shaft length: usually short 30mm from mud tank bottom Impeller: prepeller type Impeller layers: two layers
9-5/8" Air-Operated Thread Protector Product Description Air-operated thread protectors offer safe, reliable casing and tubing pin-end protection. The working principle of air-operated protectors is based on pressurization by rig air (116 to 130 psi, or 800 to 896 kPa), which ensures easy installation and reliable protection for all API standard and premium threads. Three types of air-operated thread protectors are available: â?¢ The HD protector is designed for mild and cold climates. â?¢ The HDH protector is designed for use in tropical areas such as the Middle and Far East, Africa, South America, and parts of Australia. â?¢ The HD-T/HDH-T protector is designed for tender-assisted rigs and pickup/laydown machines. The T-type protector has an aluminum reinforcement embedded in the buffer. Features, Advantages, and Benefits: These durable protectors provide a 360° grip with greater, evenly divided holding power. Durability is enhanced because the outside of the protectors does not change; only the inside inflates to provide a better grip on the pin. Absence of moving parts, metal clamping bars, or other mechanisms provides a long and virtually maintenance-free life cycle. The bottom of each protector contains a rugged buffer. Air operated thread protectors provide firm attachment to all thread types for greater operational flexibility. Rugged construction makes this protectors resistant to high temperatures and rough handling for a long life cycle. Pressurization by air facilitates installation and release for operational efficiency. Technical Parameters Model HD Protector HDH Protector HD-T/HDH-T Protector Yellow top, black bottom Orange top, black bottom Orange top, green bottom Applications Mild and cold climates Tropical climates Tender-assisted rigs and pickup /laydown machines Hardness body/buffer (Shore A) 78/95 88/95 Tensile strength 33/26 N/mm2 Abrasion 40/100 mm3 Temperature range (°F, °C) -31 to +100 -35 to +38 +55 to +1 49 +13 to +65
API 7K QW175 QW 205 QW 275 QW 375 Air Pneumatic Slip for rotary table Product Description High Quality Drill Pipe Air Slips, QW 275 Type Pneumatic Slips QW Type Pneumatic Slip is an ideal well-head mechanized tool with double functions, it can automatically handle the drill pipe when the drilling rig is running in hole or does pipe wiping when the drilling rig is pulling out of hole. It can accommodate different kinds of drilling rig rotary table. And it features convenient installation, easy operation, complete functions, high automation, low labor intensity, and can improve the drilling speed. Technical Specifications: Model QW-175 QW-205(520) QW-275 QW-375 Suited for which rotary tables ZP175 ZP205(ZP520) ZP275 ZP375 Working pressure MPa 0.60.9 psi 87 -130 Effective clamping length mm 350 420 420 420 in 133/4 161/2 161/2 161/2 Rated load kN 2250 2500 2500 2500 Slip extenstion height mm < 300 in
API 7K Mud Pump Parts Gasket O-Ring Packing Product Description Lake Petro offers a wide range of gaskets and packing materials for usage in drilling pumps. Gaskets and packings made of polyurethane, rubber and combination of fabric and rubber. Lake Petro has very rich experience in supplying spare parts of mud pump to the worldwide Oil Drilling industry.We stock and sell a wide selection of mud pump fluid end expendables and spares parts. Mud pump parts for F series mud pump, For P series mud pump, For PZ series mud pump, For 3NB series mud pump. These parts include liners, pistons, valves & seats,piston rods, rod clamps, extension rods, all fluid end seals and gaskets, fluid cylinder modules and accessories, as well as power end components, such as crankshaft assemblies, gear sets, connecting rods, crosshead, and bearings.
Rongsheng F1600 Mud Pump Crosshead Product Description The crosshead supplied by Lake Petro is manufactured from high quality, cast steel and the guides are from a quality manganese bronze normally used in bearings. This combination of materials provides a low friction interface and generates very little heat, which indications no friction, which equates to no wear. Lake Petro has very rich experience in supplying spare parts of mud pump to the worldwide Oil Drilling industry.We stock and sell a wide selection of mud pump fluid end expendables and spares parts. Mud pump parts for F series mud pump, For P series mud pump, For PZ series mud pump, For 3NB series mud pump. These parts include liners, pistons, valves & seats,piston rods, rod clamps, extension rods, all fluid end seals and gaskets, fluid cylinder modules and accessories, as well as power end components, such as crankshaft assemblies, gear sets, connecting rods, crosshead, and bearings.
The following example is for you reference: 1.Description: Manual tongs are necessary tools applied to make up and break out pipes.Changing lug jaws and latch steps can adjust different handling sizes of the tongs.They are designed and manufactured according to API Spec 7K Specification for drilling and well servicing equipment. Q3 1/2"~13 3/8"-75 Type SB Manual Tong Type SB Manual Tong is an essential tool in oil operation to fasten or remove the screws of drill pipe and casing joint or coupling .The handling size of manual tong can be adjusted by changing latch lug jaws and latch steps.The available range of manual tong is from 3 1/2~13 3/8 inch. 2.Key Words: Manual Tong, Drilling Manual Tong, SB Type Manual Tong. 3.Features: (1).API 7K certified quality assured. (2).Easy to operation to holding different size by changing the lug jaw. (3).Spare parts available after sales,all parts are traceable. (4).Size range from 3 1/2~13 3/8. (5).Rated Torque range from 40kN·m to 75kN·m. 4.After-sales Service Provided: No overseas service provided. 5.Warranty: one year. 6.Certificaiton: API 7K. 7.Condition: New. 8.Color: Required. 9.Model: Type SB. 10.Rated Torque(kN*m): 40~75. 11.Size Range: 3 1/2"~13 3/8". 12.Place of Origion: China(Mainland). 13.Minimun Order: 1Set(s). 14.Material: Carbon Steel. 15.Processing Type: Forging. 16.Machine Type: Drilling Equipment. 17.Use: Well Drilling. 18.Processing Time: 30days. 19.Supply Ability: 50sets/per month. 20.Payment Terms: T/T; L/C; Western Union. 21.Packing&Delivery: (1).Packing Details:Standard Export Package. (2).Port:China Main Port.
The following example is for you reference: 1.Description: Manual tongs are necessary tools applied to make up and break out pipes.Changing lug jaws and latch steps can adjust different handling sizes of the tongs.They are designed and manufactured according to API Spec 7K Specification for drilling and well servicing equipment. Q3 1/2"~17"-90 Type DB Manual Tong Type DB Manual Tong is an essential tool in oil operation to fasten or remove the screws of drill pipe and casing joint or coupling .The handling size of manual tong can be adjusted by changing latch lug jaws and latch steps.The available range of manual tong is from 3 1/2~17 inch. 2.Key Words: Manual Tong, Drilling Manual Tong, DB Type Manual Tong. 3.Features: (1).API 7K certified quality assured. (2).Easy to operation to holding different size by changing the lug jaw. (3).Spare parts available after sales,all parts are traceable. (4).Size range from 3 1/2~17. (5).Rated Torque range from 55kN·m to 90kN·m. 4.After-sales Service Provided: No overseas service provided. 5.Warranty: one year. 6.Certificaiton: API 7K. 7.Condition: New. 8.Color: Required. 9.Model: Type DB. 10.Rated Torque(kN*m): 50~90. 11.Size(in): 3 1/2"~17". 12.Place of Origion: China(Mainland). 13.Minimun Order: 1Set(s). 14.Material: Carbon Steel. 15.Processing Type: Forging. 16.Machine Type: Drilling Equipment. 17.Use: Well Drilling. 18.Processing Time: 30days. 19.Supply Ability: 300sets/per month. 20.Payment Terms: T/T; L/C; Western Union. 21.Packing&Delivery: (1).Packing Details:Standard Export Package. (2).Port:China Main Port.
