DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
BARILAC barrier coatings are the most suited sustainable solution to replace polycoated laminated board, waxcoated, PVDC coated etc all non sustainable alternatives. Barilac barrier coat is recommended for paper cup, trays, foodtrays, pizza boxes, ice cream cartons etc. The special product features are. - Low COBB - Good oil and grease resistance - Good Moisture Vapour Transmission rate - Good heat sealing performance - Good water resistance - Low odour - FDA compliance
RUBEX-OEL wood coating is an environmentally friendly Carbolineum replacement product in rosewood tone, low odor and quick drying for outdoor use. Size 5 litres 10 litres 25 litres RUBEX-OEL wood coating is an environmentally friendly carbolineum substitute product in rosewood tone, low odor and quick drying for outdoor use. Penetrates deep into the wood and provides a water-repellent effect, effectively protects old and new wood against weathering, rot and fungal attack. Color: brown. Not suitable for benches, tables, chairs, etc. Weight n/a Size 5L, 10L, 25L
Size 5 litres 10 litres 25 litres 200 litres Winstrip KAL 800 cold paint stripper "PH 12-14 strongly alkaline" KAL 800 is a highly alkaline cold paint stripper made from organic solvent phases. Suitable for cold application up to approx. 30C. (When heated, the product is used up more quickly) It is suitable for parts made of iron, steel, aluminum, copper, chrome steel, etc. Quickly and efficiently removes powder coatings, PU paints. Only partially suitable for water-based paints. etc. Size 5L, 10L, 25L, 200L
Winstrip WSL 1300 hot paint stripper liquid PH 1-4 strongly acidic WSL 1300 is a mulifunctional, ready-to-use hot paint stripper up to 60C. Size 5 litres 10 litres 25 litres 200 litres Winstrip WSL 1300 liquid hot paint stripper "PH 1-4 strongly acidic" WSL 1300 is a multifunctional, ready-to-use hot paint stripper up to 60C. Based on special organic solvents such as acids and corrosion inhibitors. Only suitable to a limited extent for powder coatings. Ideal for epoxy paints, PU paints, NC paints, etc. Ideal for non-ferrous metals. Call us and we will be happy to advise you Weight 5kg Size 5L, 10L, 25L, 200L
Specification: MF: ZrSiO4 Specific gravity: 4.68-4.71 Bulk density: 170-180 lb./ft3; 2700 kg/m3; Hardness: 7.8 Moh Angle of repose: 30 degree; Melting point: 4000�°F, 2550�°c Refractive index: 1.93 to 2.01 Thermal stability: no change to 3090�°F, 1700�°c Loss on ignition: 0.02%-0.12% Color: Colorless transparent crystal Refractive index